22-NA-088
Service Bulletin Details
Public Details for: 22-NA-088
This technical bulletin provides repair information to correct a customer concern of seeing a roof panel joint front finish molding gap near front of windshield.
- 2022 -
Models from 2022
2022 BRIGHTDROP EV600 |
Service Bulletin Bulletin No.: 22-NA-088 Date: April, 2022 TECHNICAL Subject: Roof Panel Joint Front Finish Molding Gap Near Front of Windshield Brand: Model: BrightDrop EV600 Involved Region or Country Model Year: from to 2022 2022 VIN: from Engine: Transmission: All All to North America Additional Options (RPOs) Condition 6051386 Some customers may comment that one, or both, of the roof panel joint front finish moldings sit higher than desired where the forward area of the upper roof cap meets the windshield. Cause The cause of the condition may be that the roof finish molding forward edge can contact adhesives used in the build process, thus not allowing it to sit flush. Correction Upon verifying the condition, follow the repair steps in the Service Procedure below. Copyright 2022 General Motors LLC. All Rights Reserved. Page 2 April, 2022 Bulletin No.: 22-NA-088 Service Procedure 6051451 1. Starting on either affected side, use a suitable work platform to access the roof panel joint front finish molding. 6051392 2. Tape off the corner of the windshield and the area where the finish molding meets the body, to protect the surfaces (3). 3. Gently place a non-marring wedge (2) in the top corner of the front roof panel to lift up the finish molding, taking special care to not disengage the plastic retainers connecting the molding to the body. Bulletin No.: 22-NA-088 April, 2022 4. Using a fine-tooth blade (1), trim off the bottom edge of the finish molding flush with the panel. Discard the bottom edge that was cut off. 5. Using a scotch bright pad, scuff the bottom side of the finish molding. 6. Cut 2 pieces of 3M™ Acrylic Foam Tape 4225, White - 2” in length. Page 3 10. Using needle nose plies, insert the tape in the position shown above. 11. Wet out the tape by pressing firmly on the corner of the finish molding to seat the panel to the tape. 6051399 6051394 7. Adhere both pieces of tape to one another, as shown. 8. Where the tape will adhere, clean the area that was scuffed, as well as the matching underside of the body with an alcohol wipe. 9. Using a heat gun, warm the tape, the finish molding and the body. 12. The finish molding should sit flush, as shown above. 13. If affected, repeat steps # 1–11 on the opposite side. Parts Information 3M® products are available through your local 3M® distributor. Information about 3M® product retailers in your area may be obtained at 1-866-364-3577 or at http://3mcollision.com/ Causal Part N/A 6051396 Description 3M™ Acrylic Foam Tape, White Part Number Material Allowance 4225 75 cents (U.S.), $1.15 (Canada) Page 4 April, 2022 Bulletin No.: 22-NA-088 Warranty Information For vehicles repaired under the Bumper-to-Bumper coverage (Canada Base Warranty coverage), use the following labor operation. Reference the Applicable Warranties section of Investigate Vehicle History (IVH) for coverage information. Labor Operation Description Labor Time 1086518* Roof Panel Joint Front Finish Molding Gap Near Front of Windshield Repair 0.4 hr Add Repeat Repair on Opposite Side 0.3 hr *This is a unique Labor Operation for Bulletin use only. Version 1 Modified Released April 25, 2022 GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information. WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION