N222362410-01

Service Update
N222362410 Main Body Wire Harness Contact Damage
Release Date:
Revision Description:
Attention:
May 2022
Revision: 01
The Service Procedure and Labor Table have been updated. Please discard all previous
copies of bulletin N222362410.
This service update includes vehicles in dealer inventory and customer vehicles that return to the
dealership for any reason. This bulletin will expire at the end of the involved vehicle’s New Vehicle Limited
Warranty period.
Make
BrightDrop
Model Year
From
To
2022
2022
Model
EV600
RPO
Description
Involved vehicles are marked “open” on the Investigate Vehicle History screen in GM Global Warranty Management
system. This site should always be checked to confirm vehicle involvement prior to beginning any required inspections
and/or repairs.
Condition
Correction
Certain 2022 model year BrightDrop EV600 vehicles have a main body wire harness (MBWH) that may
come in contact with the lower intermediate steering shaft joint (bellows).
Dealers will install butyl patches, abrasion sleeves, and zip ties.
Parts
Quantity
1
Part Name
Part No.
Parts will be
directly
shipped to
affected
dealers.
Repair Kit
Parts Pre-Ship Information – For USA & Canada Only
An initial supply of repair kits will be pre-shipped to involved dealers of record. This pre-shipment is scheduled to begin
the week of April 29, 2022. Pre-shipped parts will be charged to dealer’s open parts account. Additional parts, if required,
should be obtained from GMCCA.
Warranty Information
Labor
Operation
9106295
Description
Repair (includes inspection)
Add: Wire to Wire Repair
Add: Each Additional Wire
Labor
Time
0.8
0.5
0.2
Trans.
Type
Net
Item
ZFAT
N/A
Service Procedure
1.
Lift the vehicle. Refer to Lifting and Jacking the Vehicle in SI.
2.
Remove the front compartment air deflector. Refer to Front Compartment Air Deflector Replacement in SI.
3.
Remove the left front tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in SI.
Copyright 2022 General Motors. All Rights Reserved.
Page 1 of 5
Service Update
N222362410 Main Body Wire Harness Contact Damage
6043726
4.
Locate the wire harness running along the driver’s side frame rail beneath and behind the I-shaft as shown.
5.
Inspect the wire harness for any damage.
•
If no damage is found, proceed to the next step.
•
If any damage is found, repair the wire harness. Refer to Wire to Wire Repair in SI.
6051378
6.
Rotate the zip tie strap ends so the tie strap ends point either up or down as shown. They should not point toward
the I-shaft boot.
Page 2 of 5
Service Update
N222362410 Main Body Wire Harness Contact Damage
6051425
7.
Install four butyl patches in locations shown.
6051420
Page 3 of 5
Service Update
N222362410 Main Body Wire Harness Contact Damage
6051422
8.
Install the zip tie (1) through the bottom hole in the frame and feed it through the adjacent inner side rail hole as
shown. Wrap the zip tie around the main body wire harness and tighten by hand, then use pliers to snug the zip tie
down all the way.
9.
Install the zip tie (2) through the holes that go directly through the center of the frame rail as shown. Wrap the zip tie
around the main body wire harness and tighten by hand, then use pliers to snug the zip tie down all the way.
10. Clip the excess off both zip ties so they are flush with the heads.
11. Inspect the steering shaft boot for signs of damage.
•
If no damage is found, proceed to the next step.
•
If damage is found, open a new warranty line and replace the intermediate steering shaft under warranty. Refer
to Intermediate Steering Shaft Replacement in SI.
12. Confirm the gap between the closest part of the I-shaft boot and the main body wire harness is .5 inch (12.5 mm) at
a minimum.
6055825
13. Locate the AC line (1) between the main body wire harness and the steering gear.
Page 4 of 5
Service Update
N222362410 Main Body Wire Harness Contact Damage
6055834
14. Install the anti-abrasion sleeve (1) around the AC line as shown.
15. Secure the anti-abrasion sleeve (1) with the zip tie (2).
16. Clip the excess off the zip tie so it is flush with the head.
17. Rotate the zip tie strap end so the tie strap end points either up or down as shown. It should not point toward any
surrounding components.
18. Install the left front tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in SI.
19. Install the front compartment air deflector. Refer to Front Compartment Air Deflector Replacement in SI.
20. Lower the vehicle. Refer to Lifting and Jacking the Vehicle in SI.
Dealer Responsibility
Whenever a vehicle subject to this service update enters your vehicle inventory or is in your facility for service in the
future, and the vehicle is still covered under the New Vehicle Limited Warranty, you must take the steps necessary to be
sure the service update correction has been made before selling or releasing the vehicle.
All new, used, GM Certified Used, courtesy transportation vehicles, dealer shuttle vehicles, etc. in dealers' possession
and subject to this bulletin must be held and inspected/repaired per the service procedure of this bulletin before customers
take possession of these vehicles. Involved vehicles must be held and not delivered to customers, dealer-traded,
released to auction, used for demonstration, or any other purpose.
All GM Certified Used vehicles currently in the dealers’ inventory within the Certified Pre-Owned Inventory System
(CPOIS) will be de-certified and must be held and remedied per the service procedure in this bulletin. Upon submitting
an accepted/paid warranty transaction in the Global Warranty Management (GWM) system, the vehicle can be re-certified
for sale within the CPOIS system, or once again be used in the CTP program.
Dealer Reports
The Inventory tab of the Open Vehicle Report will contain Service Update Bulletin VINs that apply to this field action.
This information is intended to assist dealers with the PROMPT COMPLETION of these vehicles. The Customer InService tab will not contain Service Update Bulletin VIN data because the intent of a Service Update Bulletin is to not
inconvenience a customer with a special trip for service. Service Update Bulletins are to be completed when the
customer is in for a regularly scheduled visit.
GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of
conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained
technicians have the tools, equipment, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT
assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your dealer for information on whether your
vehicle may benefit from the information.
We Support
Voluntary Technician
Certification
Page 5 of 5
GLOBAL SAFETY FIELD INVESTIGATIONS
DCS6158
URGENT - DISTRIBUTE IMMEDIATELY
Date:
May 11, 2022
Subject: REVISION: N222362410-01 - Service Update
Main Body Wire Harness Contacts Intermediate Steering Shaft Joint
Revised Service Procedure and Labor Table
Models: 2022 BrightDrop EV600
To:
All General Motors Dealers
The Service Procedure and Labor Table have been updated. Please discard
all previous copies of bulletin N222362410.
END OF MESSAGE
GLOBAL SAFETY FIELD INVESTIGATIONS