K105NAS1

SB-10043869-6804
TECHNICAL BULLETIN
K105NAS1
29 MAR 2012
THIS SERVICE ACTION IS VALID FOR A LIMITED TIME ONLY
AND WILL EXPIRE ON 31 MARCH 2014
SECTION: 417
Service Action: Right-Hand Rear Lamp LED Failure
AFFECTED VEHICLE RANGE:
XF (X250)
VIN: R00001 - R61290
Model Year: 2009 - 2010
CONDITION SUMMARY:
Situation: On a limited number of 2009 – 2010 model year Jaguar XF vehicles within the VIN range above,
the light emitting diode (LED) within the right-hand (RH) rear lamp assembly may fail due to corrosion of the
silver lead frame.
Action: Retailers are required to 'HOLD' all affected vehicles within their control and refrain from releasing
the vehicles for onward distribution and sale pending completion of the rework actions detailed in this
bulletin. Affected vehicles in the hands of owners should be repaired at the next available opportunity. At
the time of customer appointment, ensure that all outstanding service campaigns for each individual vehicle
are identified and allocate sufficient time and resources to complete all campaigns. Refer to the Repair
Procedure outlined below.
PARTS:
PART NO.
DESCRIPTION
QTY
% OF VEHICLES REQUIRING PART*
C2Z16256
Lamp cluster – RH
1
**
C2Z22775
Vent tube kit
6*
**
* Minimum order fulfillment is a package of six (6) vent tubes; vent tubes are only supplied in packs
of six (6). Three (3) vent tubes are required only if the RH lamp is not replaced; new lamps do not
require vent tubes.
** The majority of vehicles will only require vent tubes be installed and not a lamp replaced; the
expected lamp replacement rate is inline with current retailer replacement rate.
TOOLS:
Refer to Workshop Manual for any required special tools
WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times / prices are subject to
change; those quoted here must be taken as guidance only. Always refer to DDW to obtain the
latest repair time. Check DDW to ensure that the vehicle is affected by this Service Action prior to
undertaking any rework action. At the time of confirming a booking for vehicle repair, ensure that all
outstanding Service Actions are identified to ensure the correct parts are available and adequate
workshop time is allocated for repairs to be completed at one visit.
Warranty claims must be submitted quoting Program Code 'K105' together with the relevant Option Code
from the table. The SRO and part information listed have been included for information only.
The Option Code(s) that allows for the drive in / drive out allowance can only be claimed if the vehicle is
brought back into the workshop for this action alone to be undertaken.
This Service Action is valid for a limited time only. Warranty claims with a repair date prior to the
31 March 2014 closure date must be submitted for payment within 30 calendar days of completion of the
repair.
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and
equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some vehicles, or
provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are
not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Jaguar service facility to determine
whether this bulletin applies to a specific vehicle.
© Jaguar Land Rover North America, LLC
555 MacArthur Boulevard
Mahwah, NJ 07430
PROGRAM
CODE
OPTION
CODE
DESCRIPTION
SRO
TIME
(HOURS)
K105
B
Inspect RH rear lamp; if OK, fit vent tubes
05.10.30
0.30
C2Z22775
K105
C
Inspect RH rear lamp; if OK fit vent tubes
Drive in / drive out
05.10.30
10.10.10
0.30
0.10
C2Z22775
-
-
K105
D
Inspect RH rear lamp; if not OK, renew RH
lamp
05.10.30
0.30
C2Z16256
1
0.30
C2Z16256
1
E
Inspect RH rear lamp; if not OK, renew RH
lamp
Drive in / drive out
05.10.30
K105
10.10.10
0.10
-
-
retailers will be reimbursed for six (6) vent tubes
Normal warranty policies and procedures apply
REPAIR PROCEDURE
INSPECT RIGHT-HAND REAR LAMP ASSEMBLY OPERATION
1. Turn the exterior lights 'ON'.
•
If the right-hand (RH) rear lamp assembly LEDs are
functioning correctly, perform steps 2-4 below only.
•
If the RH rear lamp assembly LEDs are not functioning
correctly, perform step 5 below only.
2. Refer to Workshop Manual, section 417-01: Exterior Lighting,
and remove the RH rear lamp assembly.
3. Replace the vent tubes:
•
Release and remove the three (3) vent tubes from the
lamp assembly.
•
Install three (3) new vent tubes to the lamp assembly.
4. Refer to Workshop Manual, section 417-01: Exterior Lighting,
and install the RH rear lamp assembly.
NOTE: New lamps do not require vent tube installation.
5. Refer to Workshop Manual, section 417-01: Exterior Lighting,
and replace the RH rear lamp assembly.
PART NUMBER
QTY.