REHS-8430
Service Bulletin Details
Public Details for: REHS-8430
Caterpillar: on certain trucks, information is provided regarding the programming and the synchronization of keyless entry problems. Models ct660. No model years listed. *pe
Models from 2014
2014 CATERPILLAR CT660 |
Models from 2013
2013 CATERPILLAR CT660 |
Models from 2012
2012 CATERPILLAR CT660 |
Advanced Full Text Search - REHS8430 - Synchronization and Programming Keyless En... Page 1 of 3 SB-10052484-1138 Shutdown SIS Previous Screen Product: NO EQUIPMENT SELECTED Model: NO EQUIPMENT SELECTED Configuration: NO EQUIPMENT SELECTED Special Instruction Synchronization and Programming Keyless Entry{7000} Media Number -REHS8430-00 Publication Date -29/05/2013 Date Updated -29/05/2013 i05349704 Synchronization and Programming Keyless Entry{7000} SMCS - 7000 On Highway Truck: CT660 (S/N: TRK1-UP; TKL1-UP; TJS1-UP; TGT1-UP; TSW1-UP; TSY1-UP; TGD1UP; TJD1-UP) Introduction This information will assist in detecting problems with programming keyless entry. If a problem is found, correct the condition and verify that the problem is resolved. Transmitter Synchronization The transmitter may need to be re-synchronized to the truck receiver when the battery is replaced or when the transmitter has not been used for an extended time. If the transmitter fails to operate under one of these situations, the transmitter needs synchronized by doing the following: 1. Hold the transmitter near the truck 2. Press and hold both the LOCK and UNLOCK buttons simultaneously for approximately 7 seconds. 3. When the transmitter is synchronized, the door locks will cycle once. Note: If the transmitter fails to synchronize, reprogramming of the transmitters may be necessary. Refer to Programming Additional Transmitters. Programming Additional Transmitters Note: The vehicle system module has four memory slots or locations which allow up to four remote transmitters. All four locations do not have to have a transmitter programmed. For proper operation https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 6/5/2013 Advanced Full Text Search - REHS8430 - Synchronization and Programming Keyless En... Page 2 of 3 all transmitters must be programmed at the same time. If a new transmitter is being added to an existing vehicle module, all the original transmitters must also be reprogrammed in the same programming session or the transmitters will not work. Note: The following steps must be performed in exact sequence. 1. Set the vehicle parking brake. 2. Turn the truck ignition switch to the OFF position. 3. Locate the programming connectors #1 and #2 at the top right of the fuse block. Illustration 1 https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 6/5/2013 Advanced Full Text Search - REHS8430 - Synchronization and Programming Keyless En... Page 3 of 3 Illustration 2 g03388517 4. Fuse block will have to be removed to retrieve the wires the first time. 5. Connect programming connector #1 with programming connector #2. 6. When first connected, the door locks will cycle. Keep the programming connectors connected throughout the programming process. 7. Press and hold "LOCK" and "UNLOCK" at the same time on the new transmitter(s}. After 1215 seconds, the locks will cycle and the horn will beep one time. If additional transmitters are to be programmed, repeat Step 7 on each transmitter to be programmed. 8. Disconnect programming connectors. 9. Test the remote transmitter(s} for proper operation. Copyright 1993 - 2013 Caterpillar Inc. Wed Jun 5 12:01:54 CDT 2013 All Rights Reserved. Private Network For SIS Licensees. https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 6/5/2013