JTB-00353-NAS-1

Page 1 of 2
TECHNICAL BULLETIN
JTB00353NAS1
27 JUN 2014
SB-10056265-5382
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools,
and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some
vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-ityourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized
Jaguar service facility to determine whether this bulletin applies to a specific vehicle.
SECTION: 417-01
Adaptive Front Lighting System Warning Icon Displayed
AFFECTED VEHICLE RANGE:
XK Range (X150)
Model Year:
2008-2012
VIN:
B20075-B44934
MARKETS:
NAS
CONDITION SUMMARY:
Situation: The Adaptive Front Lighting System (AFS) warning icon may be displayed (permanently or
intermittently) in the Instrument Cluster.
Cause: This may be caused by the headlamps being in failsafe mode and cannot be reset due to Diagnostic
Trouble Codes (DTC) B1D64-01, B1D65-01, B1D68-01, and/or B1D69-01 stored in the AFS Headlamp Leveling
Control Module (HLCM).
Action: Should a customer express this concern, follow the Service Instruction outlined below.
PARTS:
C2P23697
Headlamp Leveling Control Module
Quantity: 1
TOOLS:
NOTE: This is an 'Active Bulletin' that will display a functional programming shortcut if accessed
within a diagnostic session using SDD.
SDD with latest DVD and Calibration File; first available on DVD137.00 v.162
Jaguar Land Rover-approved Midtronics battery power supply
WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair
time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part
number with a quantity of zero.
DESCRIPTION
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
Headlamp Leveling Control Module - Renew
86.42.17
0.5
42
C2P23697
Headlamp Leveling Control Module - Configure
new module
86.99.38
0.2
42
C2P23697
http://topix.jaguar.jlrint.com/topix/service/document/486031
7/7/2014
Page 2 of 2
NOTE: Normal Warranty policies and procedures apply.
SERVICE INSTRUCTION:
CAUTION: A Jaguar Land Rover-approved Midtronics battery power supply must be connected to the
vehicle battery during SDD diagnosis / module programming.
CAUTION: Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these
steps may cause damage to control modules in the vehicle.
NOTE: SDD must be loaded with DVD137.00 v.162 or later.
1. Install a new Headlamp Leveling Control Module (see TOPIX Workshop Manual, section 417-01).
2. Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.
3. Turn ignition 'ON' (engine not running).
4. Connect the Symptom Driven Diagnostics (SDD) system to the vehicle and begin a new session.
5. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle and initiating the data
collect sequence.
6. Select 'Service Functions' from the Session Type screen.
7. Select 'continue'.
8. Select the 'Recommendations' tab, and then select 'Run' to perform the 'Configure new module – Headlamp
control module' option.
9. Follow all on-screen instructions to complete this task.
10. Exit the current session.
11. Disconnect the SDD and the battery power supply from the vehicle.
http://topix.jaguar.jlrint.com/topix/service/document/486031
7/7/2014