P-B-88.40/92A

Mercedes-Benz
star bulletin
The best or nothing.
Date:
April 2014
Supersedes
P-B-88.40/92a
P-B-88.40/92
Group:
88
Order No.:
Revision a: Included models: 204. 319
SUBJECT:
Models 204.0/3/9
Permanently Illuminated Star Installation Instructions
Note: These US specific instructions are for the star to be illuminated when the ignition is switched on.
l'li1
~A.
Remove Front SAM
1.
Place a piece of tape on the water deflector
to prevent damage (Figure 1).
2.
Remove cover from front SAM
3.
Remove the four screws in the front SAM.
Figure 1
This bulletin has been created and maintained in accordance with MBUSA-SLP S423QH001, Document and Data Control, and
MBUSA-SLP S424HH001, Control of Quality Records.
© 2014 Mercedes-Benz USA, LLC.
Mercedes-Benz Canada, Inc.
Dealer Workshop Services
All rights reserved. Reproduction or translation in whole
or in part is not permitted without authorization from the
publisher. Printed in U.S.A.
www.MBUSAcom
1-800-FOR-MERCedes
www.startekinfo.com
ote:
When removing screws:
•
Use suitable tool (Figure 2): 50
mm T20 Torx bit locally
sourced e.g., Milwaukee® T20
(Figure 2).
•
Also shown (Figure 2) is
Facom® tools 1\4" ratcheting
wrench for the back two
screws.
Figure 2
4.
Pull the front of the SAM
straight up while shifting it
slightly to the left and remove
from housing (Figure 3).
Figure 3
2
P-B-88.40/92a
B. Install Illuminated Star
1.
Remove connector 11 C from front SAM.
2.
Remove the wire in cavity 13 from 11C.
(Figure 4).
(Figure 4).
WNote:
Wire color is: Pink I yellow.
Figure4
3.
Plug in the wire (A, Firgure 5) from 11 C, pin
13 into the cavity of the 2 pin connector
(arrow, Figure 5) that came with "Y" adapter
harness (A207 820 02 04).
WNote:
Ensure the wire from the vehicle is in the
sam.e cavity as yellow /red wire of the "Y"
harness for the fuse.
Figure 5
4.
Plug the red wire (arrow, Figure 6)
from the "Y" adapter harness into
cavity 13 on connector 11 C.
5.
Plug the 11 C connecter back into
the front SAM.
6.
Connect Illuminated star wiring
harness (A207 820 00 00)
connector pin into 2 pin connector
(A, Figure 6).
7.
Connect harness (A, Figure 6) into
"Y" adapter harness harness (B).
Figure 6
P-B-88.40/92a
3
8.
9.
Insert square rubber stopper
(arrow, Figure 7) into the side wall
of the SAM box.
Install SAM.
Figure 7
Figure 8
10.. Fit the wire harness for the wiper motor on top of the rubber stopper for the illuminated star harness.
11. Position the fuse (arrow Figure 8) as shown for future access.
12. Install cover.
4
P-B-88.40/92a
.,
.
'
13. Remove the Star (Figure 9).
WNote:
Tilt the star out at the bottom (Figure 9). It does
not turn on model 204.
Figure 9
Figure 10
14. Remove radiator support plastic cover.
15.
16.
17.
18.
19.
Install illuminated star harness and secure into place with cable tie (arrow, Figure 10).
Install radiator support cover.
Connect and install Illuminated star.
Check and verify all connections.
Verify operation.
P-B-88.40/92a
5
Parts Information
Qty.
Part Name
Part Number
1
Illuminated star wiring harness
A207 820 00 00
1
"Y" wiring harness
A207 820 02 04
1
Illuminated star
A207 817 04 16
6
P-B-88.40/92a