S-SB-0004-12
Service Bulletin Details
Public Details for: S-SB-0004-12
Summary to be provided on a future date.
- 2013 -
Models from 2013
2013 SCION FR-S |
Technical Service Bulletin S-SB-0004-12 Rev1 (3 !:iC:::ICJrl April 13, 2012 2013 Scion FR-S Pre-Delivery Service (PDS} Service Category Section General Scion Supports ~ Market Pre-Delivery Service USA ASE Certification~ Applicability YEAR(S) MODEL(S) 2013 FR-S ADDITIONAL INFORMATION REVISION NOTICE June 24, 2013 Rev1 : • The Before Inspection, Functional Operation, Walkaround Inspection, Under Hood, and Road Test sections have been updated. Any previous printed versions of this bulletin should be discarded. Introduction Pre-Delivery Service (PDS) is a critical step in satisfying your dealership's new car customers. Customer feedback indicates the following areas deserve special attention when performing PDS: • Careful inspection for paint chips/scratches and body dents/dings. • Proper operation of electrical accessories (including interior light, clock, and radio reset). • Interior cleanliness. • Proper function of mechanical systems. Customer retention and proper maintenance of vehicles has been a major focus for Toyota and Scion. To help remind customers that regular oil changes are essential to the proper maintenance of their vehicle, dealers are required to begin installing a first oil change reminder sticker prior to delivery. By doing this, customers will be reminded to return to your dealership for their first oil change. Your current oil change reminder sticker may be used. (See PDS Check Sheet item 9 of "Final Inspection & Cleaning".) A new PDS Check Sheet has been developed for the 2013 model year Scion FR-S. Some check points have been added , expanded or clarified . Bulletins are available for items in bold type. © 2013 Toyota Motor Sales, USA Page 1 of 6 !::i~ICDl'I Rev1 S-SB-0004-12 April 13, 2012 Page 2 of 6 I 2013 Scioln FR-S Pre-Delivery Service (PDS) Warranty Poliby If the need for additional repairs or adjustment is noted during the Pre-Delivery Service, the required service should be performed under warranty. Reimbursement will be managed under the warranty poII.icy. T/ile Warranty Policy and Procedures Manual requires that you maintain the completed PDS cfleck sheet in the customer's file. If you cannot produce a completed form for each retai led vehicle upon TMS and/or Region/Distributor audit, the PDS payment amount will be subject to debit. A~ additional Repair Order completed in conjunction with normal PDS must have time punch/flags for service. If multiple repairs are performed, separate time flags must be punched for each repair. Re;mbursem~nt lnformat;on OP CODE DESCRIPTION TIME OFP T1 T2 001013 Pre-Delivery Service (PDS) 1.0 N/A N/A N/A Required Tools & Equipment REQUIRED EQUIPMENT I I I I * Essential SST. SUPPLIER Techstream 2.0* TIS Techstream PART NUMBER QTY TS2UNIT ADE Techstream Lite TSPKG1 TSLITEDLR01 f'IOTE • Only ONE of the Techstream units listed above is required. • Software version 8.10.021 or later is required. • I Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at 1-800-368-6787. Before lnspedtion . Install DCC Fuse - see check sheet 2. Connect Delivery Mode Wire Harness Connectors (Automatic Transmission ONLY) see check sheet © 2013 Toyota Motor Sales, USA 1 S-SB-0004-12 Rev1 April 13, 2012 Page 3 of 6 2013 Scion FR-S Pre-Delivery Service (PDS) Func,tional Operation Apply parking brake and cycle ignition "IG-ON," place gear selector in reverse, turn on lights and rear defogger. Unlock all doors, release fuel door, release trunk hatch. 1. Check dome, courtesy, map, and sun visor lights* 2. Check warning/indicator lights, gauges, and horn 3. Check windshield wipers and washers 4. Check headlights, instrument lights, turn signals, dimmer switch, emergency flashers, and brake lights 5. Check inside/outside rear view mirror operation/adjustment 6. Check power outlet* and cigarette lighter 7. Check audio/navigation* systems, set SSP* to FR-S, and set clock 8. Install shift-lock override button cover 9. Check sliding roof 10. Check that the electroluminescent dash illuminates when the door is opened* (Scion Series 1O vehicles only) 11. Check that the shift knob illuminates* (Scion Series 10 vehicles only) Walkaround Inspection Starting at the driver's door, check window and door lock operation and the operation of all power windows and door locks from master switch. Assure tightness of interior garnishes and check seat belts. Inspect hatch contents and lights at rear of vehicle. Inspect passenger door window regulator and lock operation and garnishes. Check seat and seat belt operation. Continue on around to the front of the vehicle checking lights. 1. Check door and door lock operation including each wireless remote control/theft deterrent system* 2. Check power window operation 3. Check that engine starts with all keys 4. Check seats and seat belt operation 5. Check rear defogger 6. Check side marker, tail, backup, and license plate lights 7. Check rear cargo area trim appearance © 2013 Toyota Motor Sales, USA S-SB-0004-12 Rev1 April 13, 2012 Page 4 of 6 2013 Sci n FR-5 Pre-Delivery Service (PDS) Walkaround I spection (Continued) . Adjust compact spare tire pressure and check jack and tool installation NOTE Compact spare tire - 60 psi (414 kPa) . . Check headlight aim Refer to the Repair Manual for procedures. 1 . Check that front and rear exterior Scion badges illuminate after unlocking vehicle* (Scion Series 10 vehicles only) Under Hood . Check engine oil and ATM* fluid levels . Check brake and clutch* fluid levels Visually inspect using see-through reservoirs. . Check engine coolant level . Check windshield washer fluid level . Check battery state-of-charge using Digital Battery System Analyzer Refer to Service Bulletin No. PG001-06, "Battery Maintenance for In-Stock Vehicles & Pre-Delivery." NOTE Battery SOC should be a minimum of 75%. Please enter the SOC Reading on the space provided on the check sheet and attach the printout to the check sheet. . Inspect for fuel, oil, coolant, and other fluid leaks Under Vehicl (On Hoist) . Remove disc brake anti-rust covers/anti-corrosion wheel film* - PD017-04 Visually inspect rotors for rust. NOTE For best rotor rust prevention, retain wheel film on vehicle until just prior to customer delivery. . Activate the Tire Pressure Warning System (TPWS) sensors - see check sheet . Inspect tires for defects/damage © 2013 Toyota Motor Sales, USA l -- S-SB-0004-12 Rev1 April 13, 2012 Page 5 of 6 2013 Scion FR-S Pre-Delivery Service (PDS) Under Vehicle (On Hoist) (Continued) 4. Install rubber body plugs Install the rubber plugs (stored in glove box) into rear torque box holes. 5. Inspect for fuel , oil, coolant, and other fluid leaks 6. Visually check bolts and nuts on chassis and powertrain for looseness 7. Inspect under the vehicle for damage, rust, etc. Road Test A complete road test helps assure customer satisfaction. Drive vehicle over a variety of road surfaces and driving conditions. Check for unusual noise and driving performance. 1. Check cold engine operation Check starting and fast idle operation performance. 2. Check engine operation during warm-up Check that engine operates smoothly during warm-up. Check for unusual noise, engine vibration, rough idle, etc. 3. Check engine at normal operating temperature Check engine performance over a broad range of driving conditions, including idle quality, acceleration, cruise, and deceleration. 4. Check clutch or automatic transmission operation Check clutch operation, including engagement, disengagement, chattering, and unusual noise. Check manual transmission operation, including shift lever/linkage and unusual noise. Check automatic transmission operation, including operation in each range, neutral start switch, and shift lock system. 5. Check brake and parking brake operation Check brake function , including unusual noise, parking brake performance, and all related brake system indicator lights. 6. Check steering operation and off-center/vehicle pull/flutter Check steering function. Check steering off-center/vehicle pull/flutter. 7. Inspect for abnormal noise and vibration 8. Inspect for squeaks and rattles © 2013 Toyota Motor Sales, USA S-SB-0004-12 Rev1 April 13, 2012 Page 6 of 6 2013 Sci n FR-5 Pre-Delivery Service (PDS) Road Test (C ntinued) . Check heater and A/C operation 1 . Check speedometer operation 1 . Check cruise control operation Final Inspect on & Cleaning . Remove interior protective covers, unnecessary labels, tags, etc. (Remove protective covers just before delivery to the customer) Remove plastic covers from door panels, seats, head restraints, and sun visors, as required. Remove labels, tags, and stickers (except those containing owner information). NOTE Consumer information labels, such as airbag information warning and bumper information labels, MUST be left on the vehicle until delivery to a retail customer. . Verify floor mat application and install using retaining clips* - S-SB-0008-1 I . Visually inspect all interior parts for installation, damage, fit, dirt, etc . . Remove Rapgard™ and clear protective bumper film* Ensure ALL glue residue is removed . . Wash and clean vehicle . Inspect paint finish for scratches, chips, rust, dents, damage, etc . . Inspect exterior body parts for proper installation, damage, rust, etc. . Place Owner's Guide and first aid kit portfolio* in glove box . Place oil change sticker on inside of windshield, top left corner Complete the mileage or date recommendation and apply the oil change reminder sticker to the inside of the windshield, top left corner. You may use your current oil change reminder sticker. 1 . Perform Techstream Health Check Perform Health Check to ensure that diagnostic trouble codes are not present. Health check results can be printed for the customer at delivery, or for the dealer file, using the Diagnostic Report function. 1 . Install front license plate and mounting bracket - see check sheet * I spec! or install when equipped or required © 2013 Toyota Motor Sales, USA