14-AT-006
Service Bulletin Details
Public Details for: 14-AT-006
Summary to be provided on a future date.
Models from 2013
2013 HYUNDAI GENESIS COUPE |
Models from 2012
2012 HYUNDAI EQUUS |
2012 HYUNDAI GENESIS |
GROUP Hyun DR 11 nEW THlnKlnG. nEW POSSIBILITIES. Technical Service Bulletin SUBJECT: AUTOMATIC TRANSAXLE NUMBER 14-AT-006 t-----------1r-------------; DATE APRIL 2014 MODEL GENESIS SEDAN (BH/DH) EQUUS SEDAN (VI) GENESIS COUPE (BK) AUTOMATIC TRANSMISSION OIL PRESSURE DATA TRANSFER This TSB supersedes TSB 12-A T-010 to add 2015 Genesis Sedan (DH) Description: This bulletin provides two procedures to transfer data to the TCM for 8-speed transmissions. The purpose of the data transfer is to enable quicker adaptive learning . 1. After replacing an 8-speed transmission: Download the oil pressure data of the new transmission from the GSW server and then input the data into the TCM using the GOS. 2. After replacing a TCM : Back up the oil pressure data from the old TCM into the GOS and then transfer the data into the new TCM. If the TCM has been replaced and the oil pressure data has not been entered (input) to the new TCM , the shift position indicator lamps on the instrument cluster (BH/DH and VI) or shift lever (BK) will blink with the ignition on and the engine off. Applicable Vehicles: 2012- Genesis Sedan 3.8L/4.6L/5.0L, 2012- Equus 4.6L/5.0L and 2013Genesis Coupe 2.0L/3.8L with 8-speed automatic transmission Warranty Information: Normal warranty applies. Labor operation for automatic transmission or TCM replacement includes the time for data transfer. Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service Advisors, Technicians, Body Shop Manager, Fleet Repair SUBJECT: AUTOMATIC TRANSAXLE OIL PRESSURE DATA TRANSFER GOS SYSTEM AND TCM UPDATE PRECAUTIONS: • • • • Connect the power supply connector (D) to the GOS. Connect the USB cable (C) between the GOS and the VCI (B). Connect the 16-pin DLC connector (E) from the VCI into the DLC located under the driver's side dash. • • • Make sure the vehicle's battery is fully charged. If not, run the engine to charge the battery or attach a battery charger. Perform the input procedure with the ignition switch in the ON position and the engine off. Place the shift lever in Park. Turn off all lights (Do not leave the headlight switch in auto mode) and all accessories (including heater/air conditioner/fan, audio, heated seats, rear defroster, etc) to ensure the battery will not be discharged during the update . • Perform the update with the ignition key in the ON position. • Do not disconnect any cables connected to the vehicle or the GOS during the update. • Do not start the engine or turn the ignition switch OFF during the update. If you encounter GOS related problems, call the GIT Helpline at 888-437-0308. TSB #: 14-AT-006 Page 2 of 9 SUBJECT: I. AUTOMATIC TRANSAXLE OIL PRESSURE DATA TRANSFER Procedure after replacing an automatic transmission Oil pressure data input procedure using Auto Mode (With Internet connection) 1. Enter the VIN or select the vehicle model and model year and click A/T as the system . Click OK 2. From the GOS home screen, select Option Treatment. ft: VC-1 lJ~1n On Gi>) Ci- V MI l)rt ll' User' s Guide int!'rnt t I ~ CgJ lYI Notice 0 l Configuration I Search ~ '1 ··~---"'·------·-··-----~---------------·-----···---~---··········-~---···----··----------------------' GENESIS(BH)/2012/G 3.8 GDI Preparatio- ; ; - jl D Vehicle lnfo 0 -1: ~gn~~--- -~ SNJ ~~~~~-~~tl D Baste lnspecho-;;- -i Repair ~-;;ta~g -I l D ECU Upgrade 1 , a OTC Analysis a Data Analysis : l' •By Symptom a Flight Record 1 •By Model .Jr •By OTC . Transmission/Automattc Transaxle a Replacement ! D Component Info ! ~ 'c , ' D Inspection / Test I D Circuit Diagram I , D CARS 080-11 •Campaign 3. Select the oil pressure characteristics input (Transmission exchange). f n ia GDI ~ ·························································································-··························J .....,,. ( ., Re•ett;ng Auto TIA Values Case Analysis TSB #: 14-AT -006 OTC Current Data Ac luation Test ~ OVOM i r-- IOsclllosoope Sim ulation Test Page 3 of 9 SUBJECT: 4. AUTOMATIC TRANSAXLE OIL PRESSURE DATA TRANSFER Confirm the vehicle conditions required for the oil pressure characteristics input and then select OK. (Oil-pressure Characteristics 8 ackUp & Input (TCU Exchange)} This function Is to back-up from old TCU (be exchanged) in GDS and to Input data to new TCU 1. IG On 2. Shift Leve r : P 3. Vehic le Speed : OKmlh 4. Engine stop ... .. Actuation Currentoata Test Right Record J DVO~ 5. Input the last six digits of the new transmission serial number and select OK. (Oi~p r essure Characteristics Input (fransmmision Excha ng e)} Input Serial No and press OK button [ldlfll "Input methodll Input complete Serial No. Or. ant; 6 numbers among Serial No. [GOS] Case Analysts loo34nl OTC CurrentData Actuation Test Fllght Record OVOM j I Osc11toscop< l Sim1~ation Test ~ Docl.l!lent - WordPad TSB #: 14-AT-006 Page 4 of 9 SUBJECT: AUTOMATIC TRANSAXLE OIL PRESSURE DATA TRANSFER 6 . The serial number will display. Click on the serial number and then select OK. Preparation {Ori-pressure Characteristics Input (Transmmislon Exchange)] 1 serial number are detected. please select the corresponding Serial No and press OK bullon. [>dill] Sirial Number #:M!:IM1kiti [GOS) OTC Current Data Actuation Tes t J • 7. The oil pressure data characteristics will display. Select OK to input the data. {Ol ~p ressure Characteristics Input (Tran smmlslon Exthange)] This dala Is the Ol~pressure Characteristics of newTransmlssion that was detected by Serial No tfyou want to Input this Charactertstics to TCU, press OK button IXABMB 1003477 (!) - .j 5497 j 6989 .• u - [GOS] ~· • tL !' IRT05 567C 3445 - 17498 ~ I A658 [TCU) Cl!seAnalysls OTC Currentoata Actuation Test Flight Record lI OVOM 8. At the next screen, select OK to finish. NOTE: If the GOS cannot display the oil pressure data, go to Page 6, Manual Mode. TSB #: 14-AT-006 Page 5 of 9 SUBJECT: AUTOMATIC TRANSAXLE OIL PRESSURE DATA TRANSFER Oil pressure data input procedure using Manual Mode (No Internet connection) 1. If internet is not connected , the pop-up screen shown below will be displayed. Click OK. Preparation ® (Oil-pressure Characteri stics Input (Transmmlslon Exchange)! (Serve r] \ _ ........................................... ~ I@ 011- oressure llil Oil-pressure Corresponding Serlal No Is not detected. ~ [.............~~~.~:::~~~~ ............~ '. .t~ (GOS] ~-------- u w.< [TCU) 2. Input the serial number and 56 digit oil pressure data from the new A/T sticker. Select OK. (Oil- pressureCharacteristicslnput(Tr·ansmmislonExchange)J Please enter Serial No and the Oil-pressure Characteristics of8arcodestlckerattatchedon new transmlsslonlntheorder inthespacebeloy,·. (Allfll I .•• [GOS) u w...·· [TCUJ 3. At the next screen , select OK to finish . 4. Erase any OTC in the Engine, ESC, EPB and SCC menus. 5. Clear any DTCs in the Bluelink system according to instructions in TSB 12-BE-005-2. 6. From the home screen , select Option Treatment and Resetting Auto TA Values and select Reset. 7. Attach a GOS and select A/T Menu , Current Data and TPS (Throttle Position Sensor). Relearn the TCM: • Move the shift lever from N->R->N->D five times, pausing for 3 seconds in each gear. • Accelerate the vehicle at a steady 15-30% TPS through gears 1-2-3-4-5-6-7-8. Repeat 5 times. TSB #: 14-AT-006 Page 6 of 9 SUBJECT: AUTOMATIC TRANSAXLE OIL PRESSURE DATA TRANSFER II. Oil pressure data input after replacing or exchanging a TCM Oil pressure data input procedure using GOS 1. Enter the vehicle information by entering the vehicle's VIN or selecting the vehicle model and model year. Select A/T as the system and then click OK. 2. From the home screen, select Option Treatment. Select Oil pressure characteristics back-up & input (TCU exchange) . • . . . . ... . . ... . ... ! 1i> ... Oil-pressure Characteristics Input (Transmm ision Exchange) ' Oil-pressure Characteristics BackUp & Input (TCU Exchange) 1 . "J --~-~--~-~-=-~~~ -~----------~-~-~-=~-~~ -~--=----=-~~~ -.---- case.A.,.lysls 3. OTC CLWTentOate Actuaffon Test Confirm the vehicle conditions required for the oil pressure characteristics input before replacing the TCM and then click "OK". (Oii-pressure Ch aracteristics BackUp & Input (TCU Exchange)( This runction Is to back-up from old TCU (be exchanged) In ODS and lo Input data to newTCU1.10 On 2. Shlft l ever : P 3. Vehicle Speed : o Kmlh 4. Engine Stop [ GOS ) ·~.. ~.lf u Current Data AcluaUon Test I 0Wlodows MediaPloyer TSB #: 14-AT-006 I J0 0 Page 7 of 9 SUBJECT: AUTOMATIC TRANSAXLE OIL PRESSURE DATA TRANSFER 4. Click the BACKUP button to back up the oil pressure data of the old TCM in the GOS. u [Ol"pressure CharacterlsUcs BackUp & Input (TCU Exchange)] ~ you wantto back up data from old TCU, pre ss •BA.CKUP"button. Or If you wan! to Input them to new TCU, pres s · INPLTr'button. [OLD TCU] r----------------(Pro cedures! 1 1. BACKUP (Back up data from old TCU to GOS) I 2. Exchange old TCU with new one I 1 I II [ GOS] ••-1o ....ll I 1 3. INPUT Onput U1e backed up data to newTCU ..ith GOS) -----------------~ u r- Case An.nlysis OTC DVOM CtJTentOata , 0 scIlloscope .,.._.. Smmfation Test r-" Internet Update Q .._ Jr 5. The screen will display the oil pressure characteristics of the old TCM . Select OK to back up to the GOS. (Oil-pressure Chara cteristics BackUp & Input (TCU Exchange)) This data Is the Oi"pressure Characte ~ sttcs or Old TCU. ~you wanl lo back up In GOS, Please press OK button P R->N->D five times, pausing for 3 seconds in each gear. Accelerate the vehicle at a steady 15-30% TPS through gears 1-2-3-4-5-6-7-8. Repeat 5 times. TSB #: 14-AT-006 Page 9 of 9