TSB-0060-14

()ObO- / 'f
7 . st.::> -
@TOYOTA TACOMA
2015 PRE-DELIVERY SERVICE CHECK SHEET
~I .a!
;~
BEFORE INSPECTION
0
01 Install Short Pi n (see page 2) ................. ............. .... .
02 Install antenna ... .............................. .. ... ........ ......
UNDER VEHICLE (ON HOIST)
:l o:
D
01 Remove disc brake anti-rust covers/anti-corrosion
w heel film* ......................................................... .............
02 Inspect tires for defects/damage and adjust air pressure
(i ncluding spare tire) ........ ..... ...........................................
03 Initialize Tire Pressure Warning System (TPWS ) (see
page 2) ............................................ ................................
04 Install wheel covers/caps/spare tire wheel covers• ........
05 Inspect for fuel, oil, coolant, and other fluid leaks .... .......
06 Inspect under the vehicle for damage, rust, etc...............
07 Visually check bolts and nuts on chassis and powertrain
for looseness .......................... ·······································
D
FUNCTIONAL OPERATION
Apply parking brake and cycle ignition "IG-ON': place gear selector m reverse
tum on lights and rear defogger. Unlock doors release fuel door
01
02
03
04
05
06
07
08
09
Check dome , courtesy , map, and su n visor lights* ........
Check warning/i ndicator lights, gauges. and horn ..........
Check windshield wipers and washers ....... .......... ....... . .
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights .............................
Check inside/outside rear view mirror operation/
adjustment* ........ .. ...........................................................
Check c igarette lighter* and power outlets ......................
Check audio/navigation*/backup ca mera* systems and
set clock· ............... ............... .........................................
Install shift- lock override button cover*............... ..... ...... ..
Check passenger airbag system cutoff switch and light' ..
DD
DD
DD
wireless remote control/theft deterrent system* .......... .. ..
05
06
07
08
(unlocked) position* ... ...... ... .. ...... .................... .......... .......
Check seats and seat belt operation ...............................
Check side marker, tail , backup, ca rgo*, and license
plate lights ......... ... ............... ...... .......... ....... .... ...... ...... ....
Check jack and tool installation ···· ···· ········· ··· ·· · ··· ····· ···· ···
Check headlight aim .... ... ...... ......................... .................
Check eng ine oi l and ATM* flu id levels ......... ....... ...... ... ...
Check brake, clutch*, and power steering fluid levels ......
Check eng ine coolant level ............................... ......... ... ...
Check windshield washer fluid leve l ....... .... ... ................ ..
05 Check battery state-of-cha rge using Digital Battery
System Analyzer (SOC Reading:
% ) .....
06 Inspect for fuel, oil, coolant, and other flu id leaks .......... ..
.
DD
D
D
DD
DD
DD
ROAD TEST
DD
DD
DO
Enter Odomete r Rea dings
Reading Before Test:
D
DD
01
02
03
04
05
06
07
08
09
10
11
DD
DD
DD
Reading After Test
Check cold engine operation ... .............. ..........................
Check engine operation during warm-up ................. ..... ...
Check e ngine at normal operating temperature ..............
Check clutch*/transm ission operation ... ..... ... ............... .. ..
Check brake and parki ng brake operation ............... ........
Check steering operation and off-center/vehicle
pull/fl utter .... ... ...... .. ... ................ ......... ... .................. ..... ....
Inspect for abnormal noise and vibration ... ............... ..... ..
Inspect for squeaks and rattles .... ... ........ ....... ...... .... ........
Check front and rear* heater and NC operation ... ......... ..
Check cruise control operation• ......................................
Set/calibrate compass* (see page 2) ..............................
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
FINAL INSPECTION AND CLEANING
DO
DD
01 Remove interior protective covers, unnecessary labels ,
tags, etc. (Remove just before delivery to customer) .......
02 Verify floor mat application and install us ing
retaining clips* ...............................................................
03 Visually inspect all interior parts for installation,
damage, fit, dirt, etc. .. ....... .. ............. ... .. ...... ..... .............. ..
04 Remove Rapgard™ and clear protective bumper film • .. ..
05 Wash and clea n vehicle .... .. ... ....... .. ........... .. .... .... .... ........
06 Inspect paint finish for scratches , chips, rust, dents,
damage, etc... .... ..................... ... ................ .. .... ........ ........
07 Inspect exterior body parts for proper installation ,
damage, rust, etc.. ...... ..... .... ......... .. ... ....... .. .. .................. .
08 Place oil c hange sticker on inside of windshie ld, top
left corne r ......................... ............ .............. .....................
09 Place Owner's Guide and fi rst aid kit portfolio*
in glove box . . . . . . . . . . .. . . . . . . . . . . . . . . . ... . ..... . . . . . . . . . . . . . . . . . . . .. .. . . . . . .
10 Perform Techstream Health Check .... ...... .... ... ....... ...... ..
11 Install front* and rea r license plates (see page 2) .......... .
DD
DD
DD
UNDER HOOD
01
02
03
04
D
A complete road test helps assure customer s atisfaction Drive veh icle over a
variety of road surfaces and driving conditions Check for unusual noise and
dnving performance.
Start at left front door. Check window and door lock operation (from master power
switch. if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks
02 Check window operation .. .... .. ....... .......... .. ... . . .. ... ... .... .. ..
03 Check that engine starts with all keys . ...... .. ... ...... ...... ....
04 Check that ch ild safety door locks are in normal
~I .a!
;~
:lo:
0
DD
WALKAROUND INSPECTION
01 Check door and door lock operation, incl uding each
August 2014
DD
DD
DD
DD
DD
DD
Inspect or install when equipped/required .
D
DD
DD
D
D
DD
DD
D
D
DD
D
COMMENTS :
Completion and retention of this form is required to comply with Toyota's Warranty Policy.
TECHNICIAN'S SIGNATURE
SERVICE MANAGER'S SIGNATURE
NAME (PLEASE PRIND
NAME (PLEASE PRINT)
Date
I
Dealer Name
I
Dealer Code
We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.
I
Vehicle Identification Number (Sticker)
SHORT PIN INSTALLATION
To minimize battery discharge the Short Pin has been removed and is stored in the engine compartment relay block.
Install the Short Pin and confirm all related DTCs (81650 and 81794) are cleared.
If any DTCs besides OTC 81650 and 81794 remain, repair the applica ble system according to the Repair Manual.
NOTE
Removing the Short Pin cuts off the power sources
relating to the dome, radio No. 1, ECU-8, and CRT fuses.
L-\
The Short Pin does NOT function as a fu se, so only install it
in the position shown.
If the vehicle is stored in the dealersh ip for a long period of
time after PDS, discon nect the negative(-) battery terminal
to prevent battery discharge. Refer to Service Bulletin No.
PG001-06, "Battery Maintenance for In-Stock Vehicles &
Pre-Delivery," for battery maintenance information.
~
~
rt
D~Do
0 OOOD(iDOO=,
ODO
Q_llOOD,
§§§DODD
~ DDaaaooooooaaoo=
0Y
3 Install Short Pin Here
1 Unders ide of Rel ay Block Cover
2 Short Pin Storage Location
TIRE PRESSURE WARNING SYSTEM (TPWS) INITIALIZATION
Refer to the Repair Manual for the Initialization procedure. Please note the spare tire does not have a TPWS sensor.
Remove the ID number labels that are attac hed to each wheel and discard .
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature, perform a
Health Check using Techstream and select the "Compensation Tire Pressure" checkbox. Compensation pressures will be
displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold.
COMPASS CALIBRATION
Refer to the Repair Manual for the Calibration procedure for vehicles equipped with a compass in the rea r view mirror.
NOTE
• Do NOT perform calibration of the compass in a place where the Earth 's magnetic field is subject to interference
(underground parking, under a steel tower, between buildings, roof parking, near a railroad crossing, near a la rge
vehicle, etc.).
• During calibration, do NOT operate electric systems (moon roof, power windows, etc.) as they may interfere with
the calibration.
FRONT* AND REAR LICENSE PLATE INSTALLATION
The followi ng procedure is recommended for front and rear license plate installation on Tacoma vehicles.
Front Installation Proced ure
Rear Installation Proced ure
1. Align the holes on the license plate with the dimples on
the bumper.
2. Install 2 self-tapping screws through the license plate
and into the front bumper at the dimples.
Length: 16.0 - 24.0 mm (0.63 - 0.94 in .)
Diameter: 6.0 mm (0.24 in.)
1. Align the holes on the license plate with the holes on
the bumper.
2. Install 2 self-tapping screws through the license plate
and into the holes in the rear bumper.
Length: 16.0 mm - 18.0 mm (0 .63 in. - 0.71 in.)
Diameter: 6.0 mm (0.24 in .)
NOTICE
• Do NOT pre-drill holes into th e bumper.
• Do NOT overtighten the self-tapping screws.
/
-
.--;?
~!Fk
--:CJ~
...
I
,.--
;-
'
... ... ... ... ...
1.~~1\\'
11,1 '.'~."~
'. h\·J.\u·~
·111 1 ·
.........
,. ........
~,,,
-<
®
'--
®
V~·
·-......
,
er.. ~
,~- 1 - --...-...,.,/
f::j~c-:
J-____
-..,.,
1
1 Dimples
2 Length
3 Diameter
-~
-:::.
4 Installation Holes
;
-- ;. . ,. . .
~· -
/