SB-2031085/1

Technical Service Bulletin
01 Cam adjuster, implausible signal - V6 FSI AVS
15 12 25 2031085/1 October 10, 2012.
Model(s)
Year
VIN Range
Vehicle-Specific Equipment
A6
2010 – 2012
A4
2009
Audi Q5
2009 – 2012
CALB Engine
A5
2009
CALA Engine
CALA Engine
All
Condition
MIL on. One or several of the following DTCs for the cam actuators are stored in ECM memory:
P11A2 cam actuator "A" cylinder 1: implausible signal
P11A4 cam actuator "B" cylinder 1: implausible signal
P11A6 cam actuator "A" cylinder 2 implausible signal
P11A8 cam actuator "B" cylinder 2: implausible signal
P11AA cam actuator "A" cylinder 3: implausible signal
P11AC cam actuator "B" cylinder 3: implausible signal
P11AE cam actuator "A" cylinder 4: implausible signal
P11B0 cam actuator "B" cylinder 4: implausible signal
P11B2 cam actuator "A" cylinder 5: implausible signal
P11B4 cam actuator "B" cylinder 5: implausible signal
P11B6 cam actuator "A" cylinder 6: implausible signal
P11B8 cam actuator "B" cylinder 6: implausible signal
Technical Background
After the activation of the cam actuator to change to the other cam profile, the pin of the
actuator is pushed back in by the cam. This is confirmed by a voltage impulse, which is
registered by the engine control unit and confirms the operation. If this does not happen, or not
at the right time, a DTC "implausible signal" is saved in ECM memory.
Check the distance of the pin tip of the cam actuator for valve lift system to the camshaft when
it is not operated with a gauge. The measurement of the tip to the basic camshaft circle outside
of the groove must be taken, see Figures 1-3 below.
© 2012 Audi of America, Inc.
Page 1 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
If this measurement is 0.9mm, the
actuator 06E103697J must be installed.
Note:
The actuator 06E103697J must only be
used, if the measurement is 0.9mm or
bigger.
Figure 1. Adjustment unit for valve lift system.
Figure 2. Measurement of distance from tip of
adjustment unit to camshaft with gauge.
© 2012 Audi of America, Inc.
Page 2 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Figure 3. Distance from adjustment unit tip to
camshaft – max. 0.9mm.
Production Solution
Not applicable.
Service
Optimized cam shaft frame from 07/2011
© 2012 Audi of America, Inc.
Page 3 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Warranty
Claim Type:
Use applicable claim type. If vehicle is outside any warranty, this Technical Service Bulletin
is informational only.
Service Number:
1551
Damage Code:
0001
Labor Operations:
Remove and install left cylinder head cover
15 82 19 06
70 TU
Remove and install right cylinder head cover
15 82 19 07
90 TU
Measure adjustment unit
15 51 19 99
10 TU
Remove and install adjustment unit
15 51 19 06
20 TU
Checking and clearing fault codes
0150 0000
20 TU
Road test prior to service procedure
No allowance
0 TU
Road test after service procedure
0121 0004
10 TU
Diagnostic Time:
Technical diagnosis at dealer’s discretion
(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:
As per TSB #2031085/1
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.
Required Parts and Tools
Part Number
Part Description
Quantity
06E103697J
Actuator
1
06E103483P
Seal
1
-OR06E103484N
© 2012 Audi of America, Inc.
Page 4 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Additional Information
All parts and service references provided in this TSB are subject to change and/or removal. Always check with
your Parts Department and service manuals for the latest information.
© 2012 Audi of America, Inc.
Page 5 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.