JTB00255NAS2

Page 1 of 5
TECHNICAL BULLETIN
JTB00255NAS2
10 OCT 2013
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools,
and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some
vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-ityourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized
Jaguar service facility to determine whether this bulletin applies to a specific vehicle.
This reissue replaces all previous versions. Please destroy all previous versions. Only refer to the
electronic version of this Technical Bulletin in TOPIx.
Changes are highlighted in gray
SECTION: 501-00
Rear Window Lower Finisher Loose
AFFECTED VEHICLE RANGE:
XJ Range (X351)
Model Year:
2010-2013
VIN:
V00047-V53430
MARKETS:
NAS
CONDITION SUMMARY:
Situation: The rear window lower finisher may be loose from the rear window glass.
Cause: This may be caused by the adhesive tape securing the finisher to the glass not creating a sufficient bond.
Action: Should a customer express this concern, follow the Service Instruction outlined below.
PARTS:
3M Scotch-Weld (translucent) DP8005
Quantity: Locally
sourced
TOOLS:
NOTE: 3M Applicator gun (62-9170-9930-1), mixing nozzle (62-9171-9953-1), and plunger (629170-9910-3) – locally sourced from 3M
3M Applicator gun
62-9170-9930-1
Mixing nozzle
62-9171-9953-1
Plunger
62-9170-9910-3
WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair
time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part
number with a quantity of zero.
http://topix.jaguar.jlrint.com/topix/service/document/440887
10/14/2013
Page 2 of 5
DESCRIPTION
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL PART
Secure rear window glass
lower seal
10.10.99
0.20
07
C2D13405 (vehicles with privacy
glass)
Secure rear window glass
lower seal
10.10.99
0.20
07
C2D13406 (vehicles without
privacy glass)
NOTE: Normal Warranty policies and procedures apply.
SERVICE INSTRUCTION:
1. Open the luggage compartment lid.
2.
NOTE: Make sure that the luggage
compartment latch is put in to the closed
position to reduce the battery voltage drain.
Using a suitable tool, position the luggage
compartment latch to the closed / latched position.
3.
NOTE: To aid installation, note the
installed position of the rear window glass
seal.
Carefully remove the rear window glass finisher.
4. Using a suitable tool, remove the three (3) sections
of adhesive tape from the rear window glass.
5. Using a suitable cleaning fluid, clean the lower
edges of the rear window glass.
http://topix.jaguar.jlrint.com/topix/service/document/440887
10/14/2013
Page 3 of 5
6. Using a suitable cleaning fluid, clean the outer
faces and the channel of the rear window glass
finisher.
7. Using a suitable blade, remove and discard the
section of the rear window glass finisher shown.
8.
NOTE: Make sure that the correct parts
are used; failure to follow this instruction
may result in an incorrect adhesive mixture.
Assemble the applicator gun as shown.








Mixing nozzle (part number 62-9171-9953-1)
Adhesive (part number DP8005)
Applicator gun (part number 62-9171-9953-1)
Plunger (part number 62-9170-9910-3)
http://topix.jaguar.jlrint.com/topix/service/document/440887
10/14/2013
Page 4 of 5
9.
NOTE: Use special tools 3M Applicator
gun (62-9170-9930-1), mixing nozzle (629171-9953-1), and plunger (62-9170-99103) and adhesive DP8005.
NOTE: Make sure that the sealant is not
applied to the outer edges of the finisher.
Using the applicator gun, apply a 2mm bead of the
sealant in to the lower corner of the rear window
glass finisher.

 Apply a continuous bead of sealant along the
length of the rear window glass finisher
channel, apart from the sections of the channel
that are within 10mm of the ends.
10.
NOTE: Install the rear window glass
finisher to the previously installed position.
Carefully install the rear window glass finisher.

 Starting at one end, make sure the rear
window glass finisher is correctly aligned to the
rear window glass.
11.
NOTE: Make sure that the tape applies a
suitable pressure on the rear window glass
finisher until adhesion has been completed.
NOTE: Make sure that the tape does not
touch the top edge of the rear window glass
finisher; failure to follow this instruction may
result in the tape bonding with the sealant.
Using a suitable tape, secure the finisher in to the
correct position.

 Firmly press the tape on to the lower edge of
http://topix.jaguar.jlrint.com/topix/service/document/440887
10/14/2013
Page 5 of 5
the rear window glass finisher and hold in
place.

 Whilst applying tension to the tape, secure the
upper section of the tape to the rear window
glass.

 Make sure that the tape does not remain in
contact with rear window glass at the top of
the rear window glass finisher.
12. Repeat the above step at suitable intervals across
the width of the finisher
13. Wait 90 minutes.
14. Remove the tape.
15. Clean the surrounding area.

 Make sure that all tape residue and excess sealant is removed.
16. Release the luggage compartment latch.
17. Close the luggage compartment lid.
http://topix.jaguar.jlrint.com/topix/service/document/440887
10/14/2013