K204 UPS7113

Page 1 of 3
TECHNICAL BULLETIN
K204 UPS7113-1bNAS1
10 DEC 2013
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools,
and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some
vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-ityourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized
Jaguar service facility to determine whether this bulletin applies to a specific vehicle.
SECTION: 415-00
Update Prior to Sale: Map Routing
AFFECTED VEHICLE RANGE:
XF (X250)
Model Year:
VIN:
2014
U09031-U14856
XJ Range (X351)
Model Year:
VIN:
2014
V58603-V63129
F-TYPE (X152)
Model Year:
VIN:
2014
K00074-K09736
MARKETS:
NAS
CONDITION SUMMARY:
Situation: An issue has been identified with the navigation map routing on 2014 model year F-TYPE, XF, and XJ
vehicles within the listed VIN ranges where the routing algorithm tends to not utilize freeways enough, taking
customers onto highways and local roads rather than keeping them on the freeway for longer.
Action: Retailers are required to HOLD all affected vehicles within the listed VIN range that are in their control
and refrain from releasing the vehicles for new or used vehicle sale pending completion of the rework action
detailed in this Technical Bulletin. Unsold vehicles must have this performed prior to vehicle handover to the
customer.
PARTS:
No parts required
SPECIAL TOOLS:
NOTE: This document is an 'Active Bulletin' that will display a functional programming shortcut if
accessed within a diagnostic session using SDD.
SDD with latest SDD-DVD and Calibration File; first available on DVD135.08 v.152
Jaguar Land Rover-approved Midtronics Battery Power Supply
http://topix.jaguar.jlrint.com/topix/service/procedure/448813/ODYSSEY_FSA/G170746...
12/11/2013
Page 2 of 3
Refer to Workshop Manual / Service Instruction for any required tools
WARRANTY:
NOTE: Check DDW to ensure that the vehicle is affected by this program prior to undertaking any
rework action. Repair procedures are under constant review, and therefore times / prices are subject to
change; those quoted here must be taken as guidance only. Refer to the Repair Times Searcher (RTS) on
TOPIx to obtain the latest repair time. At the time of confirming a booking for vehicle repair, ensure that
all outstanding Service Actions are identified to ensure the correct parts are available and adequate
workshop time is allocated for repairs to be completed at one visit.
Warranty claims must be submitted quoting Program Code 'K204' together with the relevant Option Code from the
table. The SRO and part information listed have been included for information only. The Option Code(s) that allows
for the drive in / drive out allowance can only be claimed if the vehicle is brought into the workshop for this action
alone to be undertaken.
This program is valid for a limited time only. Warranty claims with a repair date prior to the 28 February 2014
closure date must be submitted for payment within 30 calendar days of completion of the repair.
PROGRAM
CODE
OPTION
CODE
DESCRIPTION
SRO
TIME
(HOURS)
PARTS
QTY. /
VALUE
K204
B
Update Audio front control module
software
86.99.72 0.7
-
-
K204
C
Update Audio front control module
software
Drive in/drive out
86.99.72 0.7
10.10.10 0.1
-
-
NOTE: Normal Warranty policies and procedures apply
SERVICE INSTRUCTION:
1.
CAUTION: Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform
these steps may cause damage to control modules in the vehicle.
CAUTION: A Jaguar Land Rover-approved Midtronics battery power supply must be connected
to the vehicle battery during SDD diagnosis / module programming.
NOTE: SDD must be loaded with DVD135.08 v.152 or later.
Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.
2. Turn ignition 'ON' (engine not running).
3. Connect the Symptom Driven Diagnostics (SDD) system to the vehicle and begin a new session.
4. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle and initiating the data
collect sequence.
http://topix.jaguar.jlrint.com/topix/service/procedure/448813/ODYSSEY_FSA/G170746...
12/11/2013
Page 3 of 3
5. Select 'Diagnosis' from the Session Type screen.
6. Select the 'Selected Symptoms' tab, and then select the following:

 Electrical - Information and entertainment system - Navigation system - Route guidance
7. Select the 'Extras' tab.
8. From the Recommendations tab, select Run to perform the 'Configure existing module – Audio front control
module' option.
9. Follow all on-screen instructions to complete this task.
10. Exit the current session.
11. Disconnect the SDD and the battery power supply from the vehicle.
http://topix.jaguar.jlrint.com/topix/service/procedure/448813/ODYSSEY_FSA/G170746...
12/11/2013