LTB00603NAS1

Service Bulletin Details

Public Details for: LTB00603NAS1

Summary to be provided on a future date.


- 9999 -

Page 1 of 2
TECHNICAL BULLETIN
LTB00603NAS1
25 OCT 2013
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools,
and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some
vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-ityourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Land
Rover service facility to determine whether this bulletin applies to a specific vehicle.
SECTION: 413-00
Early Service Indicator Reset Not Available
AFFECTED VEHICLE RANGE:
LR2 (LF)
Model Year:
VIN:
2013 Onwards
DH321215 Onwards
MARKETS:
NAS
CONDITION SUMMARY:
Situation:
The Service Interval Indicator may not be able to be reset unless the 'SERVICE REQ'D XXXX MLS (XXXX km) / XX
DAYS' or 'SERVICE REQUIRED' message is already displayed in the Instrument Cluster (IC) message center.
Cause: Instrument Cluster (IC) software requires the SERVICE REQUIRED message to be displayed in the IC
before the Service Interval Indicator manual reset procedure can be completed.
NOTE: Refer to the LR2 Maintenance Check Sheet on TOPIx for scheduled service intervals. The
Service Interval Indicator must not be reset unless all of the items covered under the appropriate
service (1-year, 2-year, etc.) are performed. The Instrument Cluster (IC) software update is only
required once.
Action: Should a customer request a full scheduled service prior to the display of either 'SERVICE REQUIRED'
message, follow the Service Instruction outlined below to update Instrument Cluster (IC) software and then
proceed with the Service Interval Indicator manual reset procedure (see SSM58917 for procedure details).
PARTS:
No Parts Required
TOOLS:
NOTE: This document is an 'Active Bulletin' that will display a functional programming shortcut if
accessed within a diagnostic session using SDD.
SDD with latest DVD and Calibration File; first available on DVD134.10 v.142
Jaguar Land Rover-approved Midtronics battery power supply
WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to change;
http://topix.landrover.jlrint.com/topix/service/document/442378
10/28/2013
Page 2 of 2
those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair
time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part
number with a quantity of zero.
DESCRIPTION
SRO
TIME (HOURS)
CONDITION CODE
CAUSAL PART
Update Instrument Cluster software
88.90.03
0.20
42
LR039632
NOTE: Normal Warranty policies and procedures apply.
SERVICE INSTRUCTION:
1.
CAUTION: A Jaguar Land Rover-approved Midtronics battery power supply must be connected
to the vehicle battery during SDD diagnosis / module programming.
NOTE: SDD must be loaded with DVD134.10 v.142 or later.
Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.
2. Turn ignition 'ON' (engine not running).
3. Connect the Symptom Driven Diagnostics (SDD) system to the vehicle and begin a new session.
4. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle and initiating the data
collect sequence.
5. Select 'Diagnosis' from the Session Type screen.
6. Select the 'Selected Symptoms' tab, and then select the following:
 Electrical - Instruments - Information and message center - Message display area - Powertrain
7. Select 'continue'.
8. Select the 'Recommendations' tab.
9. From the Recommendations tab, select 'Run' to perform the 'Configure existing module – Instrument cluster
control module' option.
10. Follow all on-screen instructions to complete this task.
11. Exit the current session.
12. Disconnect the SDD and the battery power supply from the vehicle.
13. Perform the Service Interval Indicator manual reset (see SSM58917 for procedure details).
http://topix.landrover.jlrint.com/topix/service/document/442378
10/28/2013


© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.