JTB-00303-NAS-1

Page 1 of 2
TECHNICAL BULLETIN
JTB00303NAS1
03 JUL 2013
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools,
and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some
vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-ityourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized
Jaguar service facility to determine whether this bulletin applies to a specific vehicle.
SECTION: 413-01
Rhythmic 'Blip' Noise From Front Door Speakers
AFFECTED VEHICLE RANGE:
XJ Range (X351)
Model Year:
2010-2012
VIN:
V00047-V39298
MARKETS:
NAS
CONDITION SUMMARY:
Situation: A rhythmic 'blip' noise may be heard from the front door mid-range speakers. The noise may occur
after the vehicle has been shut down for a number of minutes and is then woken up upon entry to the vehicle.
Cause: Under certain conditions the Instrument Cluster (IC) may momentarily reset. The reset induces a ring
break, which is identified as a rhythmic speaker 'blip' noise when the vehicle is woken up.
Action: Should a customer express this concern, follow the Service Instruction outlined below.
PARTS:
C2D25223
Instrument cluster
Quantity: 1
TOOLS:
NOTE: This document is an 'Active Bulletin' that will display a functional programming shortcut if
accessed within a diagnostic session using SDD.
IDS with latest IDS-DVD and Calibration File; first available on DVD134.01 v.133
Jaguar Land Rover-approved Midtronics battery power supply
WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair
time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part
number with a quantity of zero.
DESCRIPTION
SRO
TIME (HOURS)
CONDITION CODE
CAUSAL PART
Fit New Instrument Cluster
88.30.20
0.20
42
C2D23729
Configure New Instrument Cluster
86.99.25
0.30
42
C2D23729
NOTE: Normal Warranty policies and procedures apply.
http://topix.jaguar.jlrint.com/topix/service/document/422662
7/5/2013
Page 2 of 2
SERVICE INSTRUCTION:
NOTE: The following Instrument Cluster (IC) replacement procedure must be initiated with the old IC
fitted to the vehicle. Validate the accurate, current mileage has been recorded on the repair order. Make
sure a new IC is present before completing this procedure.
1.
CAUTION: A Jaguar Land Rover-approved Midtronics battery power supply must be connected
to the vehicle battery during IDS / SDD diagnosis / module programming.
NOTE: IDS must be loaded with DVD134.01 v.133 or later.
Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.
2.
NOTE: Follow all SDD screen instructions; install the new Instrument Cluster (IC) only when
advised to by SDD. Refer to TOPIx Workshop Manual section 413-01 for IC replacement
instructions.
NOTE: Mileage will automatically be recorded and transferred from the old Instrument Cluster
(IC) to the new IC during the SDD replacement procedure.
Connect SDD to the vehicle and begin a new diagnostic session, by reading the VIN for the current vehicle and
initiating the data collect sequence.
3. Follow the SDD prompts.
NOTE: At the end of the Instrument Cluster (IC) SDD replacement procedure, make sure the mileage
is correct in the new IC.
4. Select 'Service functions' from the Session Type screen.
5. Select 'continue'.
6. Select the 'Recommendations' tab, and then select 'Run' to perform the 'Configure new module – Instrument
cluster control module' option.
7. Follow all on-screen instructions to complete this task.
8. Exit the current session.
9. Disconnect the IDS and the battery power supply from the vehicle.
http://topix.jaguar.jlrint.com/topix/service/document/422662
7/5/2013