18-068-16
Service Bulletin Details
Public Details for: 18-068-16
Models from 2016
2016 JEEP CHEROKEE |
Models from 2015
2015 JEEP CHEROKEE |
NUMBER: GROUP: DATE: 18-068-16 Vehicle Performance June 16, 2016 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC. SUBJECT: MIL Illumination: DTCs P112C and/or P112D OVERVIEW: This bulletin involves replacing the Post Catalyst Position O2 Sensor. MODELS: 2015 - 2016 (KL) Jeep Cherokee NOTE: This bulletin applies to vehicles within the following markets/countries: EMEA. NOTE: This bulletin applies to vehicles built on or before April 25, 2016 (MDH 0425XX) equipped with 2.0L I4 Turbo Diesel Engine (Sales Code EBT) or equipped with 2.2L I4 Turbo Diesel Engine (Sales Code EBU) with Euro Stage 6 Emissions (Sales Code NB6). SYMPTOM/CONDITION: A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) stored or active: • • P112C - O2 Sensor 2/1 Pumping Undercurrent. P112D - O2 Sensor 2/1 Pumping Overcurrent. DIAGNOSIS: Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in TechCONNECT, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the ones listed above are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. If the customer describes the symptom/condition listed above or if the technician finds the DTCs, perform the Repair Procedure. NOTE: This bulletin does not apply to the upstream (pre-catalyst) sensor. The replacement parts should never be installed in the upstream location. 18-068-16 -2- PARTS REQUIRED: Qty. Part No. Description 1 68321552AA Diesel O2 Sensor (2.2L and 2.0L AWD) 1 68322234AA Diesel O2 Sensor (2.0L FWD) REPAIR PROCEDURE: 1. Raise the vehicle. Refer to the detailed service procedures available in DealerCONNECT> TechCONNECT under: Service Info> 04 - Vehicle Quick Reference> Hoisting> Standard Procedure. 2. Remove the post catalytic oxygen sensor if the symptom/conditions or the above DTCs are present. Refer to the detailed service procedures available in DealerCONNECT> TechCONNECT under: Service Info> 14 - Fuel System> Fuel Injection, Diesel> Sensor, Oxygen> Removal/Installation> 2.2L/2.0L Diesel 1/2. NOTE: The oxygen sensor should only be replaced with the updated design. 3. Examine oxygen sensor and identify if it is the old design (Fig. 1) or if it is the new updated design(Fig. 2). Fig. 1 Old O2 Sensor 1 - Old sensor (without holes) -3- 18-068-16 Fig. 2 New O2 Sensor 1 - New sensor (with holes) 4. Is the oxygen sensor that was removed the old design? a. YES>>> Install the new updated design oxygen sensor. b. NO>>> This Bulletin does not apply. Normal diagnosis should be performed. 5. Clear any DTCs that may have been set in any modules. 6. Lower the vehicle. Refer to the detailed service procedures available in DealerCONNECT> TechCONNECT under: Service Info> 04 - Vehicle Quick Reference> Hoisting> Standard Procedure. POLICY: Reimbursable within the provisions of the warranty. TIME ALLOWANCE: Labor Operation No: 25-01-70-9G Description Sensor, Oxygen 1/2 downstream, Replace (2 - Skilled) FAILURE CODE: ZZ Service Action Skill Category 1 - Engine Repair And Performance Amount 0.3 Hrs.