A16-049

Service Bulletin
16-049
June 14, 2016
04147 Version 1
Plug-in Charging System Problem with DTC P0D9A
AFFECTED VEHICLES
Year
Model
2014
Accord Plug-In
Trim
ALL
VIN Range
ALL
SYMPTOM
The MID indicates Plug-in Charging System Problem after the vehicle finishes charging at an electric vehicle supply
equipment (EVSE) charging station.
BACKGROUND
The vehicle monitors the temperature of the two power pins on the charging inlet of the vehicle. If the temperature of the
pins is excessive or there is an unusual temperature difference between the pins, the vehicle will set DTC P0D9A
(charge inlet temperature sensor 1 range/performance problem) and output the Plug-in Charging System Problem
message on the MID.
The latest software has raised the temperature specification for charge inlet heating due to poor contacts on the EVSE.
If the temperature of the inlet rises to an unacceptable level, the new software will allow the vehicle to finish charging at
a reduced current, which will increase the charging time. The vehicle will still protect itself against excessive heat that
might damage the connector and, in extreme cases, will shut down the charging event and set a DTC. If the vehicle
already has the latest software update and still sets the DTC, the charge inlet cable assembly may need to be replaced.
PROBABLE CAUSE
Poor contacts on the EVSE.
CORRECTIVE ACTION
Based on the diagnosis, update the software or replace the charge inlet cable assembly.
PARTS INFORMATION
Part Name
Part Number
Quantity
Charge Inlet Cable
1F410-5K0-A01
1
WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation
Number
Description
Flat Rate
Time
Defect
Code
Symptom
Code
Template
ID
Failed Part
Number
223517
Update the software (only).
0.2 hr
03214
03217
16-049A
1K100-5K0-A13
1181P6
Replace the charge inlet cable
assembly (only).
0.7 hr
03214
03217
16-049B
1K100-5K0-A13
Skill Level: Repair Technician
CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools,
equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you
should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information
applies, contact an authorized Honda automobile dealer.
© 2016 American Honda Motor Co., Inc. – All Rights Reserved
Page 1 of 2
SOFTWARE INFORMATION
NOTE: Unnecessary or incorrect repairs resulting from a failure to update the HDS or MVCI are not covered under
warranty.
MVCI Control Module (CM) Update:
Application Version: 3.01.50 or later
Database update: 13-Apr-2016 or later
HDS Software Version:
3.019.012 or later
Before beginning the update, make sure that both the HDS and the MVCI are updated as listed above.
Do only the update listed in this service bulletin.
Check that the MVCI indicates the applicable program ID listed below (or a later program ID) as the Available Update
when the update begins.
If the MVCI displays This vehicle does not need an update at this time during the update, the software for this
service bulletin is already installed.
For more information about updating the HDS, the MVCI, and vehicle systems, refer to S/B 01-023, Updating Control
Units/Modules.
Model
Accord Plug-In
Program ID (or later)
K0A140
Program P/N (or later)
1K101-5K0-A140
DIAGNOSIS & REPAIR PROCEDURE
1. Charge the vehicle with a level 2 EVSE (220 volts).
•
If the error is reproduced, go to step 3.
•
If the error is not reproduced, go to step 2.
2. Check the vehicle software version.
•
If the software is the latest version, go to step 3.
•
If the software is not the latest version, do the software update. Refer to S/B 01-026, Updating Control
Units/Modules. The repair is complete.
3. Replace the charge inlet cable assembly.
END
Page 2 of 2