B15-040

Service Bulletin
June 29, 2016
15-040
02230 Version 5
Firm 2nd to 3rd Gear Upshifts Under Certain Driving Conditions
Supersedes 15-040, dated October 16, 2015; See REVISION SUMMARY
AFFECTED VEHICLES
Year
2015
2015
Model
TLX
TLX
Trim
V6 2WD
V6 SH-AWD®
VIN Range
19UUB2...FA000001 to 19UUB2…FA007728
19UUB3…FA000001 to 19UUB3…FA021489
REVISON SUMMARY
•
•
•
•
•
Under AFFECTED VEHICLES, the VIN range was updated.
Under CORRECTIVE ACTION, a note was added.
The SYMPTOM was changed to BACKGROUND and revised.
A section was added to replace the transmission.
WARRANTY CLAIM INFORMATION was updated for transmission replacement.
BACKGROUND
Under very specific driving conditions the customer may notice the 2-3 upshift is more pronounced (firmer) than the
other shifts. The transmission is working properly and this does not indicate a problem. This is not a durability concern.
CORRECTIVE ACTION
To get optimal performance out of the transmission, update the TCM software, clear any DTCs, and do the PCM idle
learn procedure.
After the update has been done, if the client returns after driving the vehicle 500 miles and is still concerned about the
2-3 shift, go to REPAIR PROCEDURE; REPLACE TRANSMISSION.
NOTE:
•
•
•
•
The transmission is constantly learning.
After the update, it is important for the transmission to learn and to adapt to the client’s driving habits. This process
can only be done by allowing the client to drive the vehicle for 500 miles.
Any repair done before the client has driven 500 miles after installing the software update is subject to
debit.
To verify the correct software has been installed and the PCM idle learn is complete before ordering a transmission,
send Tech Line a transmission snapshot when you feel the hard. Failure to provide a snapshot at the time of the
order review will cause the order to be denied and it will have to be resubmitted after the snapshot is sent.
CLIENT INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment,
and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not
assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies,
contact an authorized Acura automobile dealer.
© 2016 American Honda Motor Co., Inc. – All Rights Reserved
Page 1 of 5
WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation
Number
2235A2
A
Operation
Number
Description
Flat Rate
Time
Update the TCM software
and clear any DTCs.
0.2 hr
Do the PCM idle learn
procedure.
0.1 hr
Description
Flat Rate
Time
Defect
Code
03214
Defect
Code
Symptom
Code
03217
Symptom
Code
Template ID
15-040N
Template ID
Failed Part
Number
06280-5L9-A52
Failed Part
Number
218102
Base or Tech (2WD) –
Replace the transmission
and torque converter.
5.8 hrs
03214
03217
15-040W
06227-5J4-000
218102
Advance (2WD) – Replace
the transmission and torque
converter.
5.8 hrs
03214
03217
15-040X
06227-5J4-000
Symptom
Code
Template ID
03214
03217
15-040Y
06227-5J4-000
03214
03217
15-040Z
06227-5J4-000
Operation
Number
218102
A
218102
A
Skill Level:
Description
Flat Rate
Time
Base or Tech (SH-AWD) –
Replace the transmission
and torque converter.
5.8hrs
For SH-AWD - add
0.4 hr
Advance (SH-AWD) –
Replace the transmission
and torque converter.
5.8 hrs
For SH-AWD – add
0.4 hr
Defect
Code
Failed Part
Number
Repair Technician
Page 2 of 5
REPAIR PROCEDURE – UPDATE TCM
SOFTWARE INFORMATION
NOTE: Unnecessary or incorrect repairs resulting from a failure to update the HDS is not covered under
warranty.
i-HDS Software Version:
1.001.004 or later
J2534 Software Information:
Rewrite Version 1.0.1.12 or later
Database update 08-JUN-2016 or later
Before beginning the repair, make sure that both the i-HDS and J2534 software are updated as listed above.
Do only the update listed in this service bulletin.
You cannot apply the updates with the MVCI as a standalone tool. To update the vehicle you must use the MVCI
or the DST-I interface in conjunction with the J2534 Rewrite Special PC application on the i-HDS.
For more information about updating the i-HDS and vehicle systems, refer to Service Bulletin 01-026,
Updating Control Units/Modules.
Year/Model
2015 TLX
2015 TLX
2015 TLX
2015 TLX
Trim
2WD Base/Tech
2WD Advance
SH-AWD Base/Tech
SH-AWD Advance
Program ID (or later)
J43150
J43160
L93150
L93170
Program P/N (or later)
28101-5J4-3150
28101-5J4-3160
28101-5L9-3150
28101-5L9-3160
1. Update the TCM software with the MVCI. Refer to S/B 01-026, Updating Control Units/Modules.
NOTE:
•
•
On vehicles equipped with auto idle stop, the MVCI may indicate error code 56 during the update. If you see
the error code, open the hood, disable auto idle stop using the switch in the center console area, and retry the
update again leaving the hood open.
After completing the software update, check the Idle Learning signal in the PGM-FI Data List. If it reads NOT
COMPLETE, check the Target Idle Torque Correction Learning value. If it reads 65 N·m (47.9 lb-ft), you
need to update the PCM. Refer to S/B15-038, Hesitation, Surge, High Idle, or Auto Idle Stop Does Not Work,
for software update information. If the value reads 12 N·m (8.8 lb-ft), complete the idle learn according to the
service information.
2. Clear any stored DTCs with the HDS.
3. Do the PCM idle learn procedure:
•
•
•
•
•
•
Make sure all electrical items (A/C, audio unit, rear window defogger, lights, etc.) are turned off.
Start the engine and let it reach operating temperature (the cooling fans cycle twice).
Let the engine idle for 10 minutes with the throttle fully closed.
Turn the ignition to OFF.
Jump the SCS line with the HDS.
Wait 60 seconds, then exit the SCS mode.
Page 3 of 5
REPAIR PROCEDURE – REPLACE TRANSMISSION
SOFTWARE INFORMATION
NOTE: Unnecessary or incorrect repairs resulting from a failure to update the HDS is not covered under
warranty.
i-HDS Software Version:
1.001.004 or later
J2534 Software Information:
Rewrite Version 1.0.1.12 or later
Database update 08-JUN-2016 or later
Before beginning the repair, make sure that both the i-HDS and J2534 software are updated as listed above.
Do only the update listed in this service bulletin.
You cannot apply the updates with the MVCI as a standalone tool. To update the vehicle you must use the MVCI
or the DST-I interface in conjunction with the J2534 Rewrite PC application on the i-HDS.
For more information about updating the i-HDS and vehicle systems, refer to Service Bulletin 01-026,
Updating Control Units/Modules.
Program ID’s for replacement transmission.
Model
Program ID or above
Program ID or Above
2WD BASE, TECH
4A590
28101-5J4-A590
2WD ADVANCE
4A690
28101-5J4-A690
SH-AWD BASE, TECH
9A690
28101-5L9-A690
SH-AWD ADVANCE
9A700
28101-5L9-A700
Required Parts for 2WD and SH-AWD:
Transmission
Application
2WD Base, Technology
Part Number
2WD Advance
SH-AWD Base, Technology
SH-AWD Advance
06200-5J4-A68RM
06200-5L9-A59RM
06200-5L9-A69RM
06200-5J4-A58RM
Required Parts for 2WD and SH-AWD:
Part Name
Flange Bolt (12 mm x 120 mm)
Flange Bolt (12 mm x 70 mm)
Flange Bolt (10 mm x 30 mm)
Flange Bolt (10 mm x 30 mm)
Flange Bolt (10 mm x 34 mm)
Flange Bolt (10 mm x 35 mm)
Flange Bolt (10 mm x 45 mm)
Flange Bolt (10 mm x 45 mm)
Flange Bolt (12 mm x 33 mm)
Flange Bolt (12 mm x 45 mm)
Flange Bolt (12 mm x 45 mm)
Flange Bolt (14 mm x 135 mm)
Bolt-Washer (8 mm x 16 mm)
Exhaust Pipe Gasket (ISHINO)
Part Number
90051-5J4-000
90051-R97-000
90161-T2F-A01
90163-SDB-A00
90162-T2A-A00
90163-SDA-A01
90163-TZ3-A00
90163-SZ3-000
90186-SDA-A00
90165-SDA-A00
90164-T2G-A01
90176-SDA-A00
90101-SWA-A00
18212-SA7-003
Quantity
1
1
3
3
4
1
1
3
2
2
1
4
2
2
Page 4 of 5
Pre-Chamber Gasket
Flange Nut (12 mm)
Castle Nut (14 mm)
Self-Lock Nut (10 mm)
Spindle Nut
Split Pin (3.0 mm x 22 mm)
Set Ring (32 mm x 2.2 mm)
Snap Ring (32 mm x 2.2 mm)
18393-SDB-A00
90371-SEF-000
90363-S3V-A01
90212-SA5-003
90305-S3V-A11
94201-30220
44319-STX-A60
44319-STX-A01
1
4
2
9
2
2
1
1
For SH-AWD, also add the following:
Part Name
12-Point Bolt (8 mm x 21 mm)
Bolt-Washer (10 mm x 30 mm)
Shaft Ring Seal Kit (SH-AWD)
Part Number
90113-S10-000
90382-SZA-003
06235-5L9-000
Quantity
8
2
1
Part Number
OL999-9011A
Quantity
1.9L (64 fl oz.)
Required Material
Part Name
Acura Long Life Antifreeze/Coolant Type 2
Repair Procedure
1. Replace the transmission; refer to service information.
2. Update the TCM. See SOFTWARE INFORMATION on page 4.
3. Clear all DTCs.
4. Do the PCM idle learn procedure.
NOTE: Before beginning the repair, make sure that the HDS is up to date.
END.
Page 5 of 5