L-SB-0039-16
Service Bulletin Details
Public Details for: L-SB-0039-16
Tsb: some 2014 2016 model year ct 200h vehicles may exhibit a mil on condition with diagnostic trouble code (dtc) P2610 (ecm/pcm engine off timer performance) present. The engine control module (ecm) logic has been modified to reduce t
Models from 2016
2016 LEXUS CT 200H |
2016 LEXUS CT HYBRID |
Models from 2015
2015 LEXUS CT 200H |
2015 LEXUS CT HYBRID |
Models from 2014
2014 LEXUS CT 200H |
2014 LEXUS CT HYBRID |
L-SB-0039-16 July 14, 2016 MIL "ON" DTC P2610 Service Category Section Market USA Engine Control Applicability YEAR(S) MODEL(S) 2014 - 2016 CT200H ADDITIONAL INFORMATION Introduction Some 2014 – 2016 model year CT 200h vehicles may exhibit a MIL “ON” condition with Diagnostic Trouble Code (DTC) P2610 (ECM/PCM Engine Off Timer Performance) present. The Engine Control Module (ECM) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure below to address this condition. Warranty Information OP CODE DESCRIPTION TIME EG1622 Reprogram ECM (PCM) 0.4 MODEL YEAR OFP 2014 89660-76080 2015 – 2016 89660-76170 T1 T2 8A 99 APPLICABLE WARRANTY This repair is covered under the Lexus Federal Emission Warranty. This warranty is in effect for 96 months or 80,000 miles, whichever occurs first, from the vehicle’s in-service date. Warranty application is limited to occurrence of the specified condition described in this bulletin. © 2016 Lexus, a division of Toyota Motor Sales, USA Page 1 of 5 L-SB-0039-16 July 14, 2016 Page 2 of 5 MIL "ON" DTC P2610 Parts Information PART NUMBER MODEL YEAR PREVIOUS NEW 2014 89660-76080 89660-76081 2015 – 2016 89660-76170 89660-76171 – 00451-00001-LBL PART NAME QTY Computer, Engine Control (ECM) – Authorized Modification Labels 1 NOTE The ECM (PCM) should NOT be replaced as part of the Repair Procedure. Authorized Modification Labels may be ordered in packages of 25 from the Materials Distribution Center (MDC) through Dealer Daily – Dealer Support Materials Orders. Required Tools & Equipment SPECIAL SERVICE TOOLS (SST) PART NUMBER QTY GR8 Battery Diagnostic Station* 00002-MCGR8 1 NOTE Additional SSTs may be ordered by calling 1-800-933-8335. REQUIRED EQUIPMENT SUPPLIER PART NUMBER Techstream 2.0* Techstream Lite QTY TS2UNIT ADE Techstream Lite (Green Cable) TSLITEPDLR01 TSLP2DLR01 * Essential SST. NOTE Only ONE of the Techstream units listed above is required. Software version 11.10.034 or later is required. Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at 1-800-368-6787. The Diagnostic Tester is NOT recommended for flash reprogramming. Please use Techstream or an approved J2534 interface to perform flash reprogramming updates. Visit techinfo.toyota.com for more information regarding J2534 reprogramming. © 2016 Lexus, a division of Toyota Motor Sales, USA 1 L-SB-0039-16 July 14, 2016 Page 3 of 5 MIL "ON" DTC P2610 Calibration Information CALIBRATION ID MODEL YEAR PREVIOUS NEW 2014 37608000 37608100 2015 – 2016 37616000 37616100 Repair Procedure 1. Using Techstream, check for the following stored DTC. DTC P2610 – ECM/PCM Engine Off Timer Performance Is the DTC present? YES – Go to step 2. NO – This bulletin does NOT apply. Continue diagnosis per the Repair Manual. © 2016 Lexus, a division of Toyota Motor Sales, USA L-SB-0039-16 July 14, 2016 Page 4 of 5 MIL "ON" DTC P2610 Repair Procedure (Continued) 2. Check for the Authorized Modifications Label affixed to the vehicle in the location shown below. Confirm if the ECM (PCM) calibration has been updated. Is the calibration ID listed NOT the latest ECM (PCM) calibration? YES – Go to step 3. NO – This bulletin does NOT apply. Disregard this Service Bulletin and continue diagnosis per the Repair Manual. Figure 1. Location of Authorized Modification Label for 2014 – 2016 CT 200h 1 Replacement ECM (PCM) Part Number (i.e., 89660-76081 or 89660-76171) 4 Date Completed 2 New Calibration ID (i.e., 37608100 or 37616100) 5 This SB Number 3 Dealer Code © 2016 Lexus, a division of Toyota Motor Sales, USA L-SB-0039-16 July 14, 2016 Page 5 of 5 MIL "ON" DTC P2610 Repair Procedure (Continued) 3. Flash reprogram the ECM (PCM). NOTE The GR8 Battery Diagnostic Station MUST be used in Power Supply Mode to maintain battery voltage at 13.5 volts while flash reprogramming vehicle. For details on how to use the GR8 Battery Diagnostic Station, refer to the GR8 Instruction Manual located on the Technical Information System (TIS), Diagnostics – Tools & Equipment – Battery Diagnostics. Follow the procedures outlined in Service Bulletin No. L-SB-0021-14, “Techstream ECU Flash Reprogramming Procedure,” and flash the ECM (PCM) with the NEW calibration file update. 4. Install the Authorized Modifications Label. A. Using a permanent marker, enter the following information on the label: ECM part number [Refer to the Parts Information section for the NEW PART NUMBER] Calibration ID(s) [Refer to the Calibration Information section for the NEW CALIBRATION ID] Dealer Code Repair Date Change Authority [This bulletin number] B. Affix the Authorized Modifications Label to the vehicle at the location shown in Figure 1. The Authorized Modifications Label is available through the MDC, P/N 00451-00001-LBL. 5. Test drive the vehicle to confirm proper vehicle operation. © 2016 Lexus, a division of Toyota Motor Sales, USA