A01167120410972

Technical Service Bulletin
01 MIL on (DTC P0011 and/or P0021 - camshaft position)
01 16 71 2041097/2 July 27, 2016. Supersedes Technical Service Bulletin Group 01 number 15-29 dated July 1,
2015 for reasons listed below.
Model(s)
Year
VIN Range
Vehicle-Specific Equipment
S6, S7, RS 7,
A8, S8
2013 - 2014
All
4.0 TFSI
Condition
REVISION HISTORY
Revision
Date
Purpose
2
-
Revised Warranty (Added GFF time)
1
7/1/2015
Initial publication
• MIL on.
• Customer may report that the engine runs irregularly.
• One of the following DTCs is stored in the engine control module (ECM), J623:
• DTC P001100 (A camshaft position (bank 1) timing over-advanced or system performance)
• DTC P002100 (A camshaft position (bank 2) timing over-advanced or system performance)
Technical Background
• On the camshaft adjustment valve, the filter element can loosen
(Figure 1).
• There is no consequential damage from loosened particles in the oil
circuit. They are gathered by the oil filter.
Figure 1. Two top filters are okay, bottom
filter is missing.
© 2016 Audi of America, Inc.
Page 1 of 3
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Production Solution
Optimized control valve production.
Service
1. The camshaft adjustment valve is fitted in four different
positions. Check the affected camshaft adjustment control
valve (see DTC entry). The following list shows which
component is affected, based on event entry:
• N205 – cylinder bank 1, inlet side
• N318 – cylinder bank 1, exhaust side
• N208 – cylinder bank 2, inlet side
• N319 – cylinder bank 2, exhaust side
2. Remove connector (Figure 2) from control valve with DTC.
3. Remove bolt (Figure 2) from control valve with DTC, then
remove valve.
4. Install O-ring on new control valve. Replace hex collard bolt
and tighten new bolt to 5 Nm.
© 2016 Audi of America, Inc.
Figure 2. Connector (1) and bolt (2) to be
removed from affected control valve.
Page 2 of 3
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Warranty
Claim Type:
• 110 up to 48/50
• G10 for CPO covered vehicles - verify owner
• If vehicle is outside any warranty, this Technical Service Bulletin is informational only.
Service Number:
1585
Damage Code:
0010
Labor Operations:
Control valve remove + reinstall
1585 1921
50 TU
1585 1922
50 TU
GFF – Checking and clearing fault codes.
0150 0000
20 TU
Road test prior to service procedure
No allowance 0 TU
Road test after service procedure
0121 0004
(For inlet side, bank 1 or bank 2)
Control valve remove + reinstall
(For exhaust side, bank 1 or bank 2)
Diagnostic Time:
10 TU
Technical diagnosis at dealer’s discretion
(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:
As per TSB #2041097/2
Required Parts and Tools
Part Number
Part Description
Quantity
06E109257T
Control valve
1
WHT002789
O-ring
1
N 91211101
Hex socket head collard bolt
1
Additional Information
All parts and service references provided in this TSB (2041097) are subject to change and/or removal. Always
check with your Parts Department and service manuals for the latest information.
© 2016 Audi of America, Inc.
Page 3 of 3
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.