K213NAS1

Page 1 of 3
TECHNICAL BULLETIN
K213NAS1
30 APR 2014
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools,
and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some
vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-ityourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized
Jaguar service facility to determine whether this bulletin applies to a specific vehicle.
SECTION: 413-00
Service Action: Brake Pad Wear Warning Indicator Light
AFFECTED VEHICLE RANGE:
XF (X250)
Model Year:
VIN:
2013
S51674-S60957
Engine:
V6 S/C 3.0L Petrol
MARKETS:
NAS
CONDITION SUMMARY:
Situation: An issue has been identified on a select number of 2013 model year Jaguar XF (X250) vehicles, fitted
with the 3.0L SC engine and within the listed VIN range only , where the Brake Pad Wear Warning Indicator may
be inoperative due to non-activation within the Car Configuration File.
Action: Retailers are required to HOLD all affected vehicles within the listed VIN range that are in their control
and refrain from releasing the vehicles for new or used vehicle sale pending completion of the rework action
detailed in this Technical Bulletin. Unsold vehicles should have this performed as part of the Pre-Delivery
Inspection (PDI) process but must have it completed prior to vehicle handover to the customer. Affected vehicles
already in the hands of customers should be updated at the next available opportunity.
PARTS:
No parts required
SPECIAL TOOLS:
NOTE: This document is an 'Active Bulletin' that will display a functional programming shortcut if
accessed within a diagnostic session using SDD.
SDD with latest SDD-DVD and Calibration File; first available on DVD137.05 v.169
Jaguar Land Rover-approved Midtronics Battery Power Supply
WARRANTY:
NOTE: Check DDW to ensure that the vehicle is affected by this program prior to undertaking any
rework action. Repair procedures are under constant review, and therefore times / prices are subject to
change; those quoted here must be taken as guidance only. Refer to TOPIx to obtain the latest repair
time. At the time of confirming a booking for vehicle repair, ensure that all outstanding Service Actions
http://topix.jaguar.jlrint.com/topix/service/procedure/474682/ODYSSEY_FSA/G1716942/e... 5/1/2014
Page 2 of 3
are identified to ensure the correct parts are available and adequate workshop time is allocated for
repairs to be completed at one visit.
Warranty claims must be submitted quoting Program Code 'K213' together with the relevant Option Code from the
table. The SRO and part information listed have been included for information only. The Option Code(s) that allows
for the drive in / drive out allowance may only be claimed if the vehicle is brought into the workshop for this action
alone to be undertaken.
This program is valid for a limited time only. Warranty claims with a repair date prior to the 30 April 2016 closure
date must be submitted for payment within 30 calendar days of completion of the repair.
PROGRAM
CODE
OPTION
CODE
DESCRIPTION
SRO
TIME
(HOURS)
PARTS / SUNDRY
CODE
QTY. /
VALUE
K213
B
Update Car
Configuration File
86.99.94 0.2
-
-
K213
C
Update Car
Configuration File
Drive in/drive out
86.99.94 0.2
10.10.10 0.1
-
-
NOTE: Normal Warranty policies and procedures apply
SERVICE INSTRUCTION:
1.
CAUTION: Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform
these steps may cause damage to control modules in the vehicle.
CAUTION: A Jaguar Land Rover-approved Midtronics battery power supply must be connected
to the vehicle battery during SDD diagnosis / module programming.
NOTE: SDD must be loaded with DVD137.05 v.169 or later.
Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.
2. Turn ignition 'ON' (engine not running).
3. Connect the Symptom Driven Diagnostics (SDD) system to the vehicle and begin a new session.
4. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle and initiating the data
collect sequence.
5. Select 'Service Functions' from the Session Type screen.
6. From the Recommendations tab, select Run to perform the 'Car configuration management - Session active
car configuration' option.
7. From the Session Active Car Configuration selection screen, select the As-Built file as the current Session
Active CCF Source.
http://topix.jaguar.jlrint.com/topix/service/procedure/474682/ODYSSEY_FSA/G1716942/e... 5/1/2014
Page 3 of 3
8. Select the 'green tick' continue button to update vehicle Car Configuration File.
9. Follow all on-screen instructions to complete this task.
10. Exit the current session.
11. Disconnect the SDD and the battery power supply from the vehicle.
http://topix.jaguar.jlrint.com/topix/service/procedure/474682/ODYSSEY_FSA/G1716942/e... 5/1/2014