JTB00463NAS1

Page 1 of 8
TECHNICAL BULLETIN
JTB00463NAS1
28 JAN 2016
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge,
tools, and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on
some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by
'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an
authorized Jaguar service facility to determine whether this bulletin applies to a specific vehicle.
SECTION: 206-03
Front Brake Pad Wear Warning Lead Fouls On The Road Wheel
AFFECTED VEHICLE RANGE:
XF (X260)
Model Year:
2016
VIN:
Y00461-Y07677
Assembly Plant: Castle Bromwich
MARKETS:
NAS
CONDITION SUMMARY:
Situation: The Amber brake warning lamp in the instrument cluster may prematurely illuminate.
Cause: This may be caused by the front brake pad wear sensor lead contacting the front left road wheel.
Action: Should a customer express this concern, follow the Service Instruction below.
PARTS:
T2H22239
Cable Tie
Quantity: 1
T2H8399
Pad Wear Warning Lead
Quantity: 1
WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to
change; those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the
latest repair time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal
part number with a quantity of zero.
DESCRIPTION
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
Pad wear sensor - Front - Check and
modify
70.91.58
0.10
07
T2H8399
Pad wear sensor - Front - Renew and
modify
70.91.59
0.30
07
T2H8399
NOTE: Normal Warranty procedures apply.
COMPONENT LOCATION
1Component location.
http://topix.jaguar.jlrext.com/topix/service/document/616214
2/1/2016
Page 2 of 8
SERVICE INSTRUCTION:
WARNING: make sure to support the vehicle with axle stands.
1Remove the front left wheel (see TOPIx Workshop Manual, section 204-04: Wheels and Tires).
2Inspect the front brake pad wear sensor lead for any damage.
• If the brake pad wear sensor lead has signs of damage, continue to step 3.
• If the brake pad wear sensor lead has no damage, continue to step 13.
3Remove the front left fender splash shield (see TOPIx Workshop Manual, section 501-02: Front End Body
Panels).
4Disconnect the brake pad wear sensor connector.
http://topix.jaguar.jlrext.com/topix/service/document/616214
2/1/2016
Page 3 of 8
5Unclip the two grommets from the mounting
brackets.
6Unclip the two grommets from the mounting
brackets.
7With care remove the brake pad wear sensor lead
from the brake pads.
http://topix.jaguar.jlrext.com/topix/service/document/616214
2/1/2016
Page 4 of 8
8Install new front brake pad wear sensor lead to
the brake pads.
9Push the two grommets into their mounting
brackets.
http://topix.jaguar.jlrext.com/topix/service/document/616214
2/1/2016
Page 5 of 8
10Push the two grommets into their mounting
brackets.
11Connect the brake pad wear sensor connector.
http://topix.jaguar.jlrext.com/topix/service/document/616214
2/1/2016
Page 6 of 8
12Install the front left fender splash shield (see TOPIx Workshop Manual, section 501-02: Front End Body
Panels).
13Pass a cable tie through the existing hole in the
brake caliper.
14Make sure that the brake pad wear warning wire
is a straight line from the grommet to the 'V'
feature.
http://topix.jaguar.jlrext.com/topix/service/document/616214
2/1/2016
Page 7 of 8
15Make sure that the cable tie is seated on the top
face and tighten the cable tie.
16Remove the excess cable tie.
http://topix.jaguar.jlrext.com/topix/service/document/616214
2/1/2016
Page 8 of 8
17Install the front left road wheel (see TOPIx Workshop Manual, section 204-04: Wheels and Tires).
http://topix.jaguar.jlrext.com/topix/service/document/616214
2/1/2016