TSB-17-23-001
Service Bulletin Details
Public Details for: TSB-17-23-001
This is a technical service bulletin, sent to dealers, providing instructions for reprogramming the tcm with updated software, in cases where dtc P0317 may be incorrectly stored in the tcm due to improper programming of the tcm.
- 2017 -
Models from 2017
2017 MITSUBISHI OUTLANDER |
Page 1 of 9 MITSUBISHI MOTORS Technical Service Bulletin SUBJECT: INCORRECT DTC P0317 STORED ON TCM (6B31) CIRCULATE TO: l[JGENERALMANAGER [ X] SERVICE ADVISOR I[X l SERVICE MANAGER No: TSB-17-23-001 DATE: February, 2017 MODEL: 2017 Outlander I[X l PARTS MANAGER I[X l TECHNICIAN I[X l WARRANTY PROCESSOR I[ l SALES MANAGER PURPOSE Due to improper programming of the Transaxle Control Module (TCM), OTC P0317 may be stored incorrectly in the TCM. This may happen when CAN data communication fails between the Electric Parking Brake (EPB) ECU and the TCM, such as when the EPB connector is disconnected. The correct OTC that should be recorded in this case is U0317, CAN time-out error (EPB). This TSB instructs dealers to reprogram the TCM with updated software to correct the issue. AFFECTED VEHICLES Certain 2017 Outlander vehicles equipped with 6B31 engines, built before the following dates and VINs: • U.S & Puerto Rico.: JA4JZ4AX7HZ005940 (September 9, 2016) • Canada: JA4JZ4AXOHZ601732 (September 12, 2016) REQUIRED OPERATIONS 1. Confirm your MUT -Ill is updated with the latest reprogramming database. 2. Reprogram the TCM with the new software. Refer to the TCM Reprogramming Chart for new software information. IMPORTANT: If an affected vehicle has a Malfunction Indicator Lamp (MIL) illuminated before reprogramming. and DTCs are listed in the TCM memory, diagnose and repair those DTCs per the service manual before reprogramming. DO NOT reprogram the TCM until the reason(s) for other DTCs being set is corrected. EQUIPMENT The following equipment is needed to reprogram the TCM. • VCI (Vehicle Communication Interface) or VCI Lite - MB991824 or MB992744. • MEDIC Laptop/Tablet with A/C power adapter - 520924, or FZG1 MK2. • MUT-III main harness 'A' (blue connector at the DLC end) - MB991910 or MB992745. • • USB 2.0 cable - MB991827 or MB992747. MEDIC 3.5/4 update at 445 or higher. • For Standalone MUT -Ill units, MUT3-SE Reprogramming Database N170101 or higher. Copyright 2017, Mitsubishi Motors North America, Inc. Continued The information contained in this bulletin is subject to change. For the latest version of this document, go to the Mitsubishi Dealer Link, (4495) MEDIC, or the Mitsubishi Service Information website (www.mitsubishitechinfo.com). Page 2 of 9 TSB-17-23-001 TCM REPROGRAMMING CHART Model 2017 Outlander (6B31) (GF0W, W6AJA) ECU Part Number Data No. 8631B552 86318801 Software Part Number Previous New 8631B552 OA 8631B552 OB REPAIR PROCEDURE SOFTWARE/MEDIC VERSION VERIFICATION 1. Verify that the TCM has not already been updated to the latest S/W number in the table above. If the TCM is at the latest level, reprogramming is not necessary. NOTE: Reprogramming the TCM with the latest database (e.g., N170101) includes all past and current reprogramming for TSBs of affected vehicles. It is not necessary to reprogram the TCM for each previous TSB. For MEDIC 3.5/4 users only: (MUT -Ill STV users go to step 5) - - .. ~--·····~ 2. ~ -•:. • w~,:_- :.•:.: ••_,...:. • Verify the MEDIC 3.5/4 is at version 3.5 and at update 445_or higher. •- If your MEDIC 3.5/4 update is at least 445, continue with the Reprogramming Procedure. If your MEDIC 3.5/4 update is below 445, update your MEDIC as follows. 3. [-~--. ---........--. --~.·---..--<1n ..... .. Tloo _ _ __, __ Ullall.911 .... :::..!',.=·--__,.,._,,_ i......,ua:; Select the MEDIC 3.5/4 Admin tab and click on "Updates." Page 3 of 9 TSB-17-23-001 4. IF the MEDIC update screen advises updates are available, click the "Begin" button. After all updates are complete, GO TO THE REPROGRAMMING PROCEDURE. 5. STANDALONE MUT-11I SCAN TOOL VIEWER (STV) ONLY: (MEDIC 3.5 USERS GO TO THE REPROGRAMMING PROCEDURE). Verify that your MUT3-SE has the most current version of the reprogramming database: From the MUT3-SE Main Page: -'-1 • Click "STV" • Click the "ECU Reprogramming" button • Click "SOB Data List" • Confirm that the database number displayed in the upper right above the chart is N170101 or higher • If the database number displayed on your MUT3-SE is N170101 or greater, continue to the Reprogramming Procedure. • If the reprogramming database number displayed on your MUT3-SE is lower than N170101, then the MUT3-SE database needs to be updated. Page 4 of 9 TSB-17-23-001 REPROGRAMMING PROCEDURE I & CAUTION NOTE: 1. I To ensure that the vehicle battery maintains 12V during the procedure, hook-up a battery charger to the vehicle during the procedure. VCI Stand-alone reprogramming is not available for this procedure. The laptop/tablet and the VCI must remain connected for the entire procedure. Connect the equipment as follows: NOTE: VCI Lite and MEDIC 4.0 Toughpad shown for illustration purposes only. Turn the MEDIC PC/tablet on. If the battery indicator in the lower right hand corner of the screen does not show a full charge, it is recommended that either the battery be charged prior to beginning, or be used with the A/C power adaptor connected. • Connect the USB cable to the VCINCI Lite. • When the laptop/tablet displays the MUT -Ill main screen, connect the USB cable to the device. • Connect the MUT -Ill main harness with the blue DLC connection to the VCINCI Lite. • Connect the blue connection of the MUT -Ill main harness to the vehicle's data link connector. • Turn the VCI power switch ON. Verify that the indicator lamp in the upper right corner of the screen is green. !&CAUTION I DO NOT DISTURB THE HARNESS CABLES OR CONNECTIONS DURING THE CODING PROCESS AS IT COULD CAUSE THE CONTROL UNIT TO LOSE DATA. IF THE USB CABLE IS DISCONNECTED DURING THIS PROCEDURE, A WARNING MESSAGE WILL DISPLAY. 2. Turn the ignition switch to the "ON" position. Page 5 of 9 TSB-17-23-001 3. Using MEDIC, from the main page, click the "MUT3-SE" icon at the top center of the screen to open MUT -Ill SE. Click the STV button. _.. .. MFI ELCATfCVtllC.SST ·-- ""-""'C$