TSB-17-31-001

Page 1 of 9
MITSUBISHI
MOTORS
Technical Service Bulletin
SUBJECT:
ILLUMINATED TPMS WARNING LIGHT
CIRCULATE TO:
l[JGENERALMANAGER
[ X] SERVICE ADVISOR
I[X l SERVICE MANAGER
No:
TSB-17-31-001
DATE:
February, 2017
MODEL:
2016-17 Outlander
I[X l PARTS MANAGER
I[X l TECHNICIAN
I[X l WARRANTY PROCESSOR I[ l SALES MANAGER
PURPOSE
When the 12V auxiliary battery voltage becomes abnormally low, or completely goes dead, and
subsequently the 12V auxiliary battery is recharged or the vehicle is jump-started, the TPMS warning
light will start flashing for about 1 minute and 20 seconds, and then remains ON after engine start-up.
The MID display will also read "TIRE PRESSURE MONITOR SERVICE REQUIRED." An initial check of
DTCs (Diagnostic Trouble Codes) may indicate low voltage DTCs, but even after all DTCs are erased,
the TPMS warning light remains ON.
This TSB instructs dealers to reprogram the ETACS ECU (with MUT3-SE) to resolve the issue.
AFFECTED VEHICLES
2016-2017 Outlander vehicles equipped with Tire Pressure Monitoring System (TPMS) and Remote
Keyless Entry (RKE).
NOTE: This issue DOES NOT apply to vehicles with F.A.S.T. Key (KOS). TPMS is controlled by the ETACS ECU
for vehicles with RKE only.
Copyright 2017, Mitsubishi Motors North America, Inc.
Continued
The information contained in this bulletin is subject to change. For the latest version of this document, go to the Mitsubishi Dealer Link,
(4512)
MEDIC, or the Mitsubishi Service Information website (www.mitsubishitechinfo.com).
Page 2 of 9
TSB-17-31-001
REPAIR PROCEDURE
I !! IMPORTANT!! I If an
affected vehicle has a Malfunction Indicator Lamp (MIL) illuminated
before reprogramming, and DTCs are listed in the ECM memory, diagnose and repair those DTCs
per the service manual before reprogramming. DO NOT reprogram the ECM until the reason(s)
for other DTCs being set is corrected.
EQUIPMENT
The following equipment is needed to reprogram the ETACS ECU.
• VCI (Vehicle Communication Interface) or VCI Lite - MB991824 or MB992744.
•
MEDIC Laptop/Tablet with A/C power adapter - 520924, or FZG1 MK2.
MUT-III main harness 'A' (blue connector at the DLC end) - MB991910 or MB992745.
•
•
USB 2.0 cable - MB991827 or MB992747.
•
MEDIC 3/4 update at 445 or higher.
•
For Standalone MUT -Ill units, MUT3-SE Reprogramming Database N170101 or higher.
ECM REPROGRAMMING CHART
Database No. 170101
Model
ETACS ECU
Part Number
Data No.
2016 - 2017 Outlander
8637B690
8637C094
NOTE:
'
-
New
8637B680-A
8637B680-B
SEW16121-01
For MEDIC 3.5/4 users only: (MUT -Ill STV users go to
step 4)
1.
~
Previous
MUT3-SE
Software
Reprogramming the ETACS ECU with the latest database (e.g., N170101) includes all past and current
reprogramming for TSBs of affected vehicles. It is not necessary to reprogram the ETACS ECU for each
previous TSB.
. . .....,
-
Software Part Number
-«
· - . ·- · -
w
·-· ·.... ~-,.......~ ::::.: -- ~.:. ~. . --
Verify the MEDIC 3.5/4 is at version 3.5 and at update
445 or higher.
If your MEDIC 3.5/4 update is at least 445, continue
with the Reprogramming Procedure.
If your MEDIC 3.5/4 update is below 445, update your
MEDIC as follows.
Page 3 of 9
TSB-17-31-001
2.
Select the MEDIC 3.5/4 Admin tab and click on
"Updates."
3.
IF the MEDIC update screen advises updates are
available, click the "Begin" button. After all updates are
complete, GO TO THE REPROGRAMMING
PROCEDURE.
4.
STANDALONE MUT-11I SCAN TOOL VIEWER
(STV) ONLY: (MEDIC 3.5 USERS GO TO THE
REPROGRAMMING PROCEDURE). Verify that your
MUT3-SE has the most current version of the
reprogramming database:
From the MUT3-SE Main Page:
1-~--.. ~.~---b.
-----~-~.--·-----dl:llJ
•I
S f N d . N ~ d m §ySW
)
--- -- 1---- ----~-,~-....... ,
\lll..8E'Mf!11 1..(1!
.
-
.,.._ ,
"""
''"'"" I """"'
- -
.
I ..,, ..,...
!16.)Ull,i!0-111
12. Once the reprogramming is initiated, the screen shown
will indicate the reprogramming progress.
~.::--
__,....r~~
~ ....... 90 . . . ~
~ta-1:i.lllill~
jlr.,-.,--,-.
3
NOTE: Do NOT disturb the cables or turn off the ignition
during reprogramming.
I
I
.j
L <.,O..
,...........,.........
i, .... _
___ ___ _
V -'
,_
-.... --- ----,--.....-J, IU1'aial
,~1
13. Click the check mark in the "Completed" dialog box to
view and confirm the reprogramming data.
'I .
' "'
__-·--
°"""':--1a.::""'
..,
1- ~--Ol
li-~
~lll'driill:i----
I
i "-
3
O,,*"ffQ/IIM ...........
~ - - - -. . . . . -
...... gl
.
V-
~~
v«SEW1en 21,.(J1
....... ,
-
-
--
.
.
.
·l
Page 8 of 9
TSB-17-31-001
• • 14. Perform an Erase and Read All DTCs.
a.
.:;:j
El.C-ATICVJITC..SST
..,....
.....,,._
.,
aU.IISt:CQtfJROL
ABSAS0'"5TC.WSS
,.=,....,
mes
~
I
,,...
...,.,
Click the "ALL OTC" button .
_.
---1--
__.
I
IWl'DF"ASI
T .,ore,, • I
.... ~.
~
•J •
_...
-- ~ ::_
r.,,
Eu:.ATICVJ1Tc.55l
Rl
CRL.RSE:COtflROL
~
w.J
0
[lJ
(a>$