A15-002 - 8-21-1
Service Bulletin Details
Public Details for: A15-002 - 8-21-1
"service bulletin - the vehicle may have one or more of the following software bugs: when in xm mode, the audio unit turns off after making an hfl call. There is no sound or there is static in the rear headphones (both wired and wirel
Models from 2015
2015 HONDA ODYSSEY |
Models from 2014
2014 HONDA ACCORD |
2014 HONDA ACCORD HYBRID |
2014 HONDA ACCORD PLUG-IN HYBRID |
2014 HONDA CROSSTOUR |
2014 HONDA ODYSSEY |
Models from 2013
2013 HONDA ACCORD |
2013 HONDA CROSSTOUR |
(g)HONDA Service Bulletin 15-002 August 21, 2015 02202 Version 1 Vehicles with Navigation: Audio Turns Off After Using HFL, No Sound/Static in Rear Headphones, and Other Listed Issues Replaces S/B 14-019, Product Update: Audio-Navigation Unit Software Update AFFECTED VEHICLES Year 2013 2014 2014 2014 2014 2014 2014 2014 2013 2014 2014 2014 2014 2014 2014 2015 2015 Model Accord Accord Accord Accord Accord Accord Accord Plug-In Accord Hybrid Crosstour Crosstour Crosstour Crosstour Crosstour Odyssey Odyssey Odyssey Odyssey Trim ALL with navigation 2-door L4 EX-L with navigation 2-door V6 EX-L with navigation 4-door L4 EX-L with navigation 4-door V6 EX-L with navigation 4-door Touring with navigation ALL ALL ALL with navigation L4 2WD EX-L with navigation V6 2WD EX-L with navigation V6 4WD EX-L with navigation V6 AWD EX-L with navigation EX-L with navigation Touring with navigation EX-L with navigation Touring with navigation VIN Range ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL ALL SYMPTOM The vehicle may have one or more of the following software bugs: • • • • • • • • • When in XM mode, the audio unit turns off after making an HFL call. There is no sound or there is static in the rear headphones (both wired and wireless). When in XM mode, the XM radio information on the center display does not match the touch screen. The info/setting screen flashes after using LaneWatch. The HFL deletes saved speed dial information and voice tags. The audio-navigation system reboots when a customer's CD is inserted. The HFL system reboots when trying to place a call using a name that contains a non-alphanumeric character. The reverse camera image stays on after shifting out of Reverse. IMID goes blank while parallel parking. CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by "do-it-yourselfers," and you should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer. © 2015 American Honda Motor Co., Inc. - All Rights Reserved Page 1 of 7 CORRECTIVE ACTION Update the navigation unit software with the applicable DVD update. TOOL INFORMATION Part Name Tool Number Quantity Navigation System DVD Update 07 AAZ-T2GA300 1 The DVD update has been recently shipped to all dealers. Additional DVDs are available for purchase through the parts system. ~...~ s~f,SE.RYED 0201~N01vo ~4to, ..,.,.->- o'lco p' ,._,;.o~ ',;)-'"' / ,~,, '\>-1l Honda "'-s--:.. Navigation ODMD Software Update ' ~ i 0 Set HONDA Serrno bullel,n HSB 15.00113.001 13.02~ for • Software updo1e · Installation 1ns1r1Jt110ns Wyourupdale disc rs lo st or damaged. reorder 1h1s disc as TN: 07AAZ ,T2GA300 WARRANTY CLAIM INFORMATION The normal warranty applies. Operation Number Description Update the navigation system software. 0100A1 Flat Rate Time Template ID 0.3 hr 15-002A Failed Part Number 39542-T2A-A91 Defect Code: 03214 Symptom Code: 03217 Skill Level: Repair Technician REPAIR PROCEDURE NOTE: • If the vehicle does not have navigation, do not use this software update. If you do, you may permanently damage the audio unit. • Apply this software update only to the vehicles listed under AFFECTED VEHICLES; otherwise, this software update can permanently damage the unit. • If you accidentally update the wrong vehicle, contact Tech Line; if the audio-navigation or audio unit must be replaced, your dealership may be debited for the replacement cost. 1. Connect a battery charger or a fully charged jumper battery to the vehicle and leave it connected during the entire update procedure to maintain a steady voltage. 2. Set the power mode to ON. Page 2 of 7 3. Wait for the navigation system to boot up, then insert the DVD into the CD slot in the center console. See TOOL INFORMATION. NOTE: The power mode must remain set to ON during the entire update procedure. If the power mode is set to OFF, the engine is started, or the DVD is removed at any time during the update process, the audionavigation unit will be locked up and you will need to use the RECOVERY PROCEDURE. NOTE: • The software update will begin. The screen will show a Reading the Disc message, then display No Data. Do not eject the disc. The unit is uploading the update and may take up to 1 minute before beginning. Both screens will shut off for about 10 seconds and reboot with the update started on both screens. The display should change to a Notification screen loading bar. • • The engine does not need to be running to do this update, even if it says so on the screen. If the No Data screen does not change after about a minute, the software may already be updated. Go to step 9 to confirm the software versions. Navigation screen Touch screen Page 3 of 7 NOTE: The software update takes about 30 minutes to complete; you do not have to oversee the update during this time as no action is needed until the update is loaded. Update Order: 1. 2. 3. 4. 5. 6. ERATO SH-BOOT SH-IPL SH-NK Utility BUuCOM On the touch screen, the progress bar will stop at 100% after ERATO is updated and remain at 100% throughout all SH and Utility updates. The progress bar will go back to 0% and resume when the BU uCOM update starts. 4. When the update is complete, the system will reboot to the HondaLink screen. The Enter code message and keypad will appear on the screens, although they may not appear at the same time. Wait for both screens to appear, then set the power mode to OFF. NOTE: • You must wait for both screen to appear before setting the power mode to OFF, or you will lock up the unit. • Do not remove the DVD until you set the power mode to OFF, because if you do so, the audio-navigation unit will lock up. If it locks up, go to RECOVERY PROCEDURE. • The audio-navigation unit may lock if any of the following occurs during the update process. If the unit locks, refer to the RECOVERY PROCEDURE to unlock it. Loss of battery power/low voltage Engine cranks or starts The power mode is set to OFF A rewrite failure occurs Navigation screen Touch screen Enter code T0 ontDr tho snclJ;rily codo nutomntically, pu•h and hold the audio power button tor 2 se-comfs. If this does no•! work, manual!~ enter lhe security cod& u-;lng lhe touch panel below. 5. Eject the DVD and wait at least 1 minute. 6. Set the power mode to ON. Once both Enter code screens appear, press and hold the power button for 2 seconds until you hear a beep. The navigation screen will show the GPS initialization message. ruw!>iiaUOti sntffll lcst power ood I s ~ hts roeatlon lliom the GJ>S $illml~1ns. Th!1 usmt11 t.altM uen than t OmlnmM.. 11 SUtl ti)(! li-J"Qll"III, • P.i:rli: ~ whiele In ao epen are,11 ifflat rrom tmos. power Uoo11. ood tall bulldll'l'IIS• Ramcrve loose .artld!l-s. rrtOCl:U! IPl'lonM.. or eleetrlcal acol!'SSOrie-s toc11tad near t:htl GPS M!irenM, The • 11 ll'iils ~ Is diis:pla)'ed repeat.edly wllliKl ~lflll tne whle!le. - your dearer. Page 4 of 7 7. Press and hold the NAVl,BACK and MENU buttons until the Select Diagnosis Items screen appears 8. Select Detail Information & Setting. 9. Select Version. Detail Information & Setting Monitor Check Unit Check Functional Setup Return GPS Information Yaw Rate Guideline Setup Version 10. Verify that the software was updated to the new version as shown below. Please note the SH-Flash, ERATO IPL, BU uCom APP, and model version information and make sure it matches the table below. Software 2013 Accord 2014 Accord 2014 Accord Plug-In 2014 Accord Hybrid Crosstour (ALL) SH ERATO BU Model 3.00.2003 3.00.0001 3.001 T2AA 2.00.2c03 2.000.020 2.001.120 T2AZ 3.00.2103 3.40.0001 3.400 T3VA 2.00.2903 2.20.0001 2.200 T3WA 3.00.2703 3.00.0001 3.001 TP6X Software Odyssey (no RES) (ALL) Odyssey w/Standard RES (ALL) Odyssey w/Ultrawide (ALL) SH ERATO BU Model 3.00.2a03 3.00.2010 3.001.E10 TK8X 3.00.2a03 3.00.2010 3.001.F10 TK8X 3.00.2a03 3.00.2010 3.001.010 TK8X NOTE: If the software is not updated, set the power mode to OFF, and go back to step 2 and repeat the update procedure. Return Version Program SH Flash HDD USB Disc ERATO IPL APP IPL X.XX.XXXX DBOOT X.XXX.XXX X.XXX.XXX HDD DSP Model X.XX.XXXX X.X.A.MAX Coveraqe xxxx A/\ BU uCom APP X.XXX Download Page 5 of 7 11. Make sure the rear camera, and LaneWatch are working properly. If not, reset the rear camera and LaneWatch. • Move vehicle to an open area. Start the engine if not already done. • Press and hold the NAVI, BACK, and MENU buttons. • Press and hold the NAVI button. • Select Incomplete. The system restarts. • When the In-Line Diag screen appears, select Start Diag. • Make sure all the icons turn green. NOTE: To get all icons to turn green, make sure that you do the following: Press the Pick-up button. Press the Hang-up button. Press the Talk button. Snap your fingers in front of the microphone to complete the test. 12. Delete all paired phones from the vehicle. Make sure the service advisor informs the customer that he or she needs to re-pair his or her phone to the vehicle. RECOVERY PROCEDURE 1. Set the power mode to OFF. 2. Make sure the DVD is inserted into the CD slot, then do a battery cable reset for 2 minutes. NOTE: Make sure the DVD is inserted when the power mode is set back to ON, because when the unit powers up, it will immediately look for the device to start the recovery process. 3. • Disconnect the negative battery cable first, then the positive cable. • Short the battery cables together with a jumper wire for 2 minutes. • Remove the jumper wire and reconnect the battery cables - positive cable first, then negative. Reattach the battery charger or fully charged jumper battery. Page 6 of 7 4. Set the power mode to ON. NOTE: Do not start the engine because starting it interrupts the steady battery power needed to update the audionavigation unit. 5. Make sure the green LEDs on each side of the DVD slot are blinking. This indicates the recovery process is working. NOTE: • The recovery procedure and software update reload take 15-30 minutes depending on when the update procedure was interrupted. • The display may stay blank during this time. 6. When the recovery procedure and software update are complete, the Enter code message and keypad screens (with navigation) appear. Set the power mode to OFF. 7. Eject the DVD and wait at least 1 minute. 8. Go to REPAIR PROCEDURE to complete the update procedure. Page 7 of 7