TSB 17-2056
Service Bulletin Details
Public Details for: TSB 17-2056
Some 2016 f-150 equipped with a 2.7l engine and built on or after 01-may-2016 may exhibit an illuminated mil with dtc P0C2A. Follow the service procedure steps to correct the condition.
- 2016 -
Models from 2016
2016 FORD F-150 |
Page 1 of 1 TECHNICAL SERVICE BULLETIN 2.7L - Illuminated Malfunction Indicator Lamp (MIL) - Diagnostic Trouble Code (DTC) P0C2A - Built On Or After 01-May2016 17-2056 04 April 2017 Model: Ford 2016 F-150 Build Date: 01-May-2016 Onwards Engine: 2.7L Issue: Some 2016 F-150 equipped with a 2.7L engine and built on or after 01-May-2016 may exhibit an illuminated MIL with DTC P0C2A. Action: Follow the Service Procedure steps to correct the condition. Parts Part Number Description FL3Z-7A103-D Transmission Fluid Auxiliary Pump Kit XT-10-QLVC Motorcraft® MERCON® LV Automatic Transmission Fluid Quantity 1 1 Warranty Status: Labor Times Description Time 2016 F-150 2.7L: Retrieve DTCs Verify Pump Operation And Reprogram The PCM (Do Not Use With Any Other Labor Operations) 0.4 2016 F-150 2.7L: Retrieve DTCs Verify Pump Operation And Replace The Transmission Fluid Auxiliary Pump (Do Not Use With Any Other Labor Operations) 1.4 Repair/Claim Coding Causal Part: 7A103 Condition Code: 42 Service Instruction 1. Connect the Ford Integrated Diagnostic System (IDS) service tool or equivalent scan tool to the data link connector (DLC). Check for DTCs. Is P0C2A stored in the powertrain control module (PCM) memory? (1). Yes – proceed to Step 2. (2). No – refer to Workshop Manual (WSM), Section 307-01 for normal diagnostics. 2. Using IDS, access transmission fluid temperature (TFT) parameter identification (PID). If TFT is below 38 ºC (100 ºF), run engine at 3000 RPM until specified temperature is achieved (approximately 2-4 minutes). 3. Using IDS, with key on engine off, command the transmission fluid auxiliary pump on using PID, TRANS_PMP_CMD to operate the transmission fluid auxiliary pump and vary the duty cycle from 20% to 90%. Is the transmission fluid auxiliary pump operating? (1). Yes - reprogram the PCM using IDS release 104.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. (2). No - replace the transmission fluid auxiliary pump. Refer to WSM Section 307-01. NOTE: ADVISE THE CUSTOMER THAT THIS VEHICLE IS EQUIPPED WITH AN ADAPTIVE TRANSMISSION SHIFT STRATEGY WHICH ALLOWS THE VEHICLE'S COMPUTER TO LEARN THE TRANSMISSION'S UNIQUE PARAMETERS AND IMPROVE SHIFT QUALITY. WHEN THE ADAPTIVE STRATEGY IS RESET, THE COMPUTER WILL BEGIN A RELEARNING PROCESS. THIS RE-LEARNING PROCESS MAY RESULT IN FIRMER THAN NORMAL UPSHIFTS AND DOWNSHIFTS FOR SEVERAL DAYS. © 2017 Ford Motor Company All rights reserved. NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by "do-it-yourselfers". Do not assume that a condition described affects your car or truck. Contact a Ford or Lincoln dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article. The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supersede this information with updates. The most recent information is available through Ford Motor Company's on-line technical resources. http://www.fordservicecontent.com/Ford_Content/vdirsnet/TSB/EU/~WTSB17-2056/US/E... 5/4/2017