T-SB-0141-14

AVALON/AVALON HV
01 Install Short Pin* (Hawaii, Puerto Rico, Saipan, Guam,
American Samoa) ............................................................
FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse, turn on lights
and rear defogger. Unlock all doors, release fuel door, release trunk hatch.
01
02
03
04
05
06
07
08
09
10
11
Check dome, courtesy, map, and sun visor lights* ..........
Check warning/indicator lights, gauges, and horn ...........
Check windshield wipers and washers ............................
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights ..............................
Check inside/outside rear view mirror operation/adjustment
Check cigarette lighter* and power outlets ......................
Check audio/navigation*/backup camera* systems and
set clock ..........................................................................
Verify Entune/Navigation software version (Display
Audio, Non-HDD Type only)*……………………………...
Install shift-lock override button cover ............................
Check sliding roof* .........................................................
Check rear sunshade operation* .....................................
WALKAROUND INSPECTION
Start at left front door. Check window and door lock operation (from master power
switch, if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks.
01 Check Smart Key System*............................................
02 Check door and door lock operation, including each
wireless remote control/theft deterrent system* ..............
03 Check window operation .................................................
04 Check that engine starts with all keys ............................
05 Check that child safety door locks are in normal
(unlocked) position ..........................................................
06 Check seats and seat belt operation ...............................
07 Check rear defogger/rear view mirror defogger* .............
08 Check side marker, tail, backup, and license plate lights
09 Check luggage compartment light* and trim appearance
10 Adjust spare tire pressure, inspect for damage, and
check jack and tool installation ........................................
11 Check headlight aim ........................................................
UNDER HOOD
01
02
03
04
05
06
Check engine oil level ......................................................
Check brake fluid level.....................................................
Check engine coolant level ..............................................
Check inverter fluid level* ……………………………...
Check windshield washer fluid level ................................
Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading: ___________%) .....
07 Inspect for fuel, oil, coolant, and other fluid leaks ............
BATTERY MAINTENANCE*
01 Perform HV battery check and maintenance ..............
* Inspect or install when equipped/required.
UNDER VEHICLE (ON HOIST)
Adjust/
Repair
October 2014
OK
OK
BEFORE INSPECTION
Adjust/
Repair
2015 PRE-DELIVERY SERVICE CHECK SHEET
01 Remove disc brake anti-rust covers/anti-corrosion
wheel film* ......................................................................
02 Inspect tires for defects/damage......................................
03 Initialize Tire Pressure Warning System (TPWS) (see
page 2) ............................................................................
04 Install wheel covers/caps/spare tire wheel covers* .........
05 Check hybrid transmission fluid level* …………………...
06 Inspect for fuel, oil, coolant, and other fluid leaks ...........
07 Inspect under the vehicle for damage, rust, etc. ..............
08 Visually check bolts and nuts on chassis and powertrain
for looseness ...................................................................
09 Install rubber body plugs (stored in glove box or center
console)* .........................................................................
10 Install front wheel opening extension pads (see page 2)
ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.
Enter Odometer Readings
Reading Before Test: _______________ Reading After Test: ________________
01
02
03
04
05
06
07
08
09
10
11
12
13
14
Check cold engine operation ...........................................
Check engine operation during warm-up .........................
Check engine at normal operating temperature ..............
Check transmission operation* .......................................
Check brake and parking brake operation .......................
Check steering operation and off-center/vehicle
pull/flutter .........................................................................
Inspect for abnormal noise and vibration .........................
Inspect for squeaks and rattles ........................................
Check Blind Spot Monitor System* ..................................
Check front and rear* heater and A/C operation..............
Check cruise control operation* .......................................
Check front seat heater/ventilation* operation .................
Check driver’s seat memory operation* ..........................
Set/calibrate compass* (see page 2) ..............................
FINAL INSPECTION AND CLEANING
01 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer).......
02 Visually inspect all interior parts for installation,
damage, fit, dirt, etc. ........................................................
03 Verify floor mat application and install using
retaining clips* ...............................................................
04 Verify green light is illuminated on SOS (Safety
Connect) button*..............................................................
05 Remove Rapgard™ and clear protective bumper film*....
06 Wash and clean vehicle...................................................
07 Inspect paint finish for scratches, chips, rust, dents,
damage, etc. ....................................................................
08 Inspect exterior body parts for proper installation,
damage, rust, etc. ...........................................................
09 Place oil change sticker on inside of windshield, top
left corner ........................................................................
10 Place Owner’s Guide and first aid kit portfolio*
in glove box ....................................................................
11 Install front license plate and mounting bracket* (see
page 2) ...........................................................................
12 Perform Techstream Health Check ................................
Completion and retention of this form is required to comply with Toyota’s Warranty Policy.
TECHNICIAN’S SIGNATURE
SERVICE MANAGER’S SIGNATURE
NAME (PLEASE PRINT)
NAME (PLEASE PRINT)
Date
Dealer Name
Dealer Code
We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.
Vehicle Identification Number (Sticker)
TIRE PRESSURE WARNING SYSTEM (TPWS) INITIALIZATION
Refer to the Repair Manual for the Initialization procedure (Avalon/Avalon HV). Please note the spare tire does not have a
TPWS sensor.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature, perform a
Health Check using Techstream and select the “Compensation Tire Pressure” checkbox. Compensation pressures will be
displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold.
FRONT WHEEL OPENING EXTENSION PAD INSTALLATION
The front wheel opening extension pad set (right and left front wheel opening extension pads and 2 tapping screws) is loaded
in the luggage compartment at the assembly plant to avoid damage in transit.
1. Remove the 2 tapping screws from the engine under cover (the screws will be reused for installation).
2. Place the left front wheel opening extension pad on the installation position as shown and tighten the 3 tapping screws.
3. Repeat steps 1 and 2 for the right side.
NOTE
There is a mark on each pad to
designate left and right side.
1 Tapping Screws
1
1
COMPASS CALIBRATION
Refer to the Repair Manual for the Calibration procedure (Avalon/Avalon HV) for vehicles equipped with a compass in the
rear view mirror.
NOTE
 Do NOT perform calibration of the compass in a place where the Earth’s magnetic field is subject to interference
(underground parking, under a steel tower, between buildings, roof parking, near a railroad crossing, near a large
vehicle, etc.).
 During calibration, do NOT operate electric systems (moon roof, power windows, etc.) as they may interfere with
the calibration.
FRONT LICENSE PLATE & MOUNTING BRACKET INSTALLATION*
The front license plate mounting bracket set (front license plate mounting
bracket, 4 long self-tapping screws and 2 short self-tapping screws) is
loaded in the luggage compartment at the assembly plant.
2
1
1. Align the holes on the front license plate mounting bracket with the
dimples on the front of the lower grille.
2. Install the 4 long self-tapping screws “B” through the holes on the
front license plate mounting bracket into the lower grille.
3. Insert the license plate into the tabs on the bracket.
Screw A: 20 mm (0.787 in.)
Screw B: 37 mm (1.456 in.)
NOTICE
 Do NOT pre-drill holes into the bumper.
 Do NOT overtighten the self-tapping screws.
3
1
1 Self-tapping Screws (B)
2 Dimples
3 Front License Plate
Mounting Bracket
1
4. Align the holes on the license plate with the corresponding holes of
the front license plate mounting bracket.
5. Install 2 short self-tapping screws “A” through the holes on the front
license plate mounting bracket and license plate.
NOTICE
 Do NOT drill holes through the front license plate mounting bracket.
 Do NOT overtighten the self-tapping screws.
3
2
1 Front License Plate
Mounting Bracket
2 License Plate
3 Self-tapping Screws (A)