T-SB-0055-14
Service Bulletin Details
Public Details for: T-SB-0055-14
Tsb: toyota venza 2015 pre-delivery service check sheet
- 2015 -
Models from 2015
2015 TOYOTA VENZA |
VENZA 01 Install antenna ................................................................. FUNCTIONAL OPERATION Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse; turn on lights and rear defogger. Unlock doors; release fuel door. 01 02 03 04 05 06 07 08 09 10 11 Check dome, courtesy, map, and sun visor lights* .......... Check warning/indicator lights, gauges, and horn ........... Check windshield wipers and washers ............................ Check headlights, instrument lights, turn signals, emergency flashers, and brake lights .............................. Check inside/outside rear view mirror operation/ adjustment ....................................................................... Check cigarette lighter* and power outlets ...................... Check audio/navigation*/backup camera* systems and set clock .......................................................................... Verify Entune/Navigation software version (Display Audio, Non-HDD Type only)* ........................................ Check sliding roof* ......................................................... Install shift-lock override button cover ............................ Check Rear Seat Entertainment system operation* ........ WALKAROUND INSPECTION Start at left front door. Check window and door lock operation (from master power switch, if equipped). Continue around vehicle in a counterclockwise direction checking each door and window operation, child door locks, seat belts, interior condition, all lights, luggage compartment contents. Finish by checking headlight aim and continue into UNDER HOOD checks. 01 Check Smart Key System*............................................ 02 Check door and door lock operation, including each wireless remote control/theft deterrent system* .............. 03 Check window operation ................................................. 04 Check that engine starts with all keys ............................ 05 Check that child safety door locks are in normal (unlocked) position .......................................................... 06 Check seats and seat belt operation ............................... 07 Check rear defogger/rear view mirror defogger* ............. 08 Check side marker, tail, backup, and license plate lights 09 Check luggage compartment light* and trim appearance 10 Adjust spare tire pressure, inspect for damage, and check jack and tool installation ........................................ 11 Check headlight aim ........................................................ UNDER HOOD 01 02 03 04 05 Check engine oil level ..................................................... Check brake fluid level..................................................... Check engine coolant level .............................................. Check windshield washer fluid level ................................ Check battery state-of-charge using Digital Battery System Analyzer (SOC Reading: ___________%) ..... 06 Inspect for fuel, oil, coolant, and other fluid leaks ............ OK UNDER VEHICLE (ON HOIST) August 2014 Adjust/ Adjust/ Repair Repair OK BEFORE INSPECTION Adjust/ Repair 2015 PRE-DELIVERY SERVICE CHECK SHEET 01 Remove disc brake anti-rust covers/anti-corrosion wheel film* ..................................................................... 02 Inspect tires for defects/damage ..................................... 03 Verify Tire Pressure Warning System (TPWS) (see page 2) ........................................................................... 04 Install wheel covers/caps/spare tire wheel covers* ........ 05 Inspect for fuel, oil, coolant, and other fluid leaks ........... 06 Inspect under the vehicle for damage, rust, etc. .............. 07 Visually check bolts and nuts on chassis and powertrain for looseness ................................................................... 08 Install rubber body plugs* (stored in glove box or center console)........................................................................... ROAD TEST A complete road test helps assure customer satisfaction. Drive vehicle over a variety of road surfaces and driving conditions. Check for unusual noise and driving performance. Enter Odometer Readings Reading Before Test: _______________ Reading After Test: ________________ 01 02 03 04 05 06 07 08 09 10 11 12 Check cold engine operation ........................................... Check engine operation during warm-up ......................... Check engine at normal operating temperature .............. Check automatic transmission operation ......................... Check brake and parking brake operation ....................... Check steering operation & off-center/vehicle pull/flutter Inspect for abnormal noise and vibration ......................... Inspect for squeaks and rattles ........................................ Check front and rear* heater and A/C operation.............. Check cruise control operation* ...................................... Check front seat heater/ventilation operation* ................. Set/calibrate compass* (see page 2) .............................. FINAL INSPECTION AND CLEANING 01 Remove interior protective covers, unnecessary labels, tags, etc. (Remove just before delivery to customer)....... 02 Visually inspect all interior parts for installation, damage, fit, dirt, etc. ........................................................ 03 Verify floor mat application and install using retaining clips* ............................................................... 04 Remove Rapgard™ and clear protective bumper film*.... 05 Wash and clean vehicle................................................... 06 Inspect paint finish for scratches, chips, rust, dents, damage, etc. .................................................................... 07 Inspect exterior body parts for proper installation, damage, rust, etc. ............................................................ 08 Place oil change sticker on inside of windshield, top left corner ........................................................................ 09 Place Owner’s Guide & first aid kit portfolio* in glove box 10 Perform Techstream Health Check ................................ 11 Install front license plate and mounting bracket* (see page 2) ............................................................................ * Inspect or install when equipped/required. Completion and retention of this form is required to comply with Toyota’s Warranty Policy. TECHNICIAN’S SIGNATURE SERVICE MANAGER’S SIGNATURE NAME (PLEASE PRINT) NAME (PLEASE PRINT) Date Dealer Name Dealer Code We hereby certify that all items on this form have been checked and corrected for proper operation as required. Vehicle Identification Number (Sticker) TIRE PRESSURE WARNING SYSTEM (TPWS) VERIFICATION 1. Connect Techstream to DLC3. 2. Adjust all tires (except the spare tire) to the standard tire inflation pressure, as indicated on the tire and loading information label on the vehicle. 3. Cycle the ignition switch to the “IG-ON” mode. NOTE To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature, perform a Health Check using Techstream and select the “Compensation Tire Pressure” checkbox. Compensation pressures will be displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold. 4. Check the tire pressure of all tires using Techstream. If the tire pressure values cannot be displayed, the system is not operating properly. Refer to the Repair Manual. 5. Remove the ID number labels that are attached to each wheel and discard. NOTE If the tire pressure values are not properly displayed (example: showing –14 psi, –100 kPa, etc.) the data from the transmitter has not been received. COMPASS CALIBRATION Refer to the Repair Manual for the Calibration procedure for vehicles equipped with a compass in the rear view mirror. NOTE Do NOT perform calibration of the compass in a place where the Earth’s magnetic field is subject to interference (underground parking, under a steel tower, between buildings, roof parking, near a railroad crossing, near a large vehicle, etc.). During calibration, do NOT operate electric systems (moon roof, power windows, etc.) as they may interfere with the calibration. FRONT LICENSE PLATE AND MOUNTING BRACKET INSTALLATION* Front License Plate Mounting Bracket: P/N 75101-0T010 1 1. Insert the front license plate into the mounting bracket. 2. Align the installation holes on the mounting bracket and front license plate with the dimples on the front bumper. 3. Screw in the 2 self-tapping screws directly into the dimples to install the front license plate and mounting bracket. 2 NOTICE Do NOT pre-drill holes into the bumper. Do NOT overtighten the self-tapping screws. 3 1 2 3 4 Dimples Front License Plate Mounting Bracket License Plate Self-Tapping Screws 4