T-SB-0060-14

TACOMA
01 Install Short Pin (see page 2)……………………………..
02 Install antenna …………………………………………….
FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse;
turn on lights and rear defogger. Unlock doors; release fuel door.
01
02
03
04
05
06
07
08
09
Check dome, courtesy, map, and sun visor lights* .........
Check warning/indicator lights, gauges, and horn ...........
Check windshield wipers and washers ...........................
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights .............................
Check inside/outside rear view mirror operation/
adjustment* .....................................................................
Check cigarette lighter* and power outlets ......................
Check audio/navigation*/backup camera* systems and
set clock* ........................................................................
Install shift-lock override button cover*............................
Check passenger airbag system cutoff switch and light* ..
WALKAROUND INSPECTION
Start at left front door. Check window and door lock operation (from master power
switch, if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks.
01 Check door and door lock operation, including each
wireless remote control/theft deterrent system* ..............
02 Check window operation .................................................
03 Check that engine starts with all keys ............................
04 Check that child safety door locks are in normal
(unlocked) position* .........................................................
05 Check seats and seat belt operation ...............................
06 Check side marker, tail, backup, cargo*, and license
plate lights ......................................................................
07 Check jack and tool installation ......................................
08 Check headlight aim ........................................................
UNDER HOOD
01
02
03
04
05
Check engine oil and ATM* fluid levels............................
Check brake, clutch*, and power steering fluid levels ......
Check engine coolant level ..............................................
Check windshield washer fluid level ................................
Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading: ___________%) .....
06 Inspect for fuel, oil, coolant, and other fluid leaks ............
* Inspect or install when equipped/required.
UNDER VEHICLE (ON HOIST)
Adjust/
Repair
August 2014
OK
OK
BEFORE INSPECTION
Adjust/
Repair
2015 PRE-DELIVERY SERVICE CHECK SHEET
01 Remove disc brake anti-rust covers/anti-corrosion
wheel film* ......................................................................
02 Inspect tires for defects/damage and adjust air pressure
(including spare tire) ........................................................
03 Initialize Tire Pressure Warning System (TPWS) (see
page 2) ............................................................................
04 Install wheel covers/caps/spare tire wheel covers* .........
05 Inspect for fuel, oil, coolant, and other fluid leaks ...........
06 Inspect under the vehicle for damage, rust, etc. ..............
07 Visually check bolts and nuts on chassis and powertrain
for looseness ...................................................................
ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.
Enter Odometer Readings
Reading Before Test: _______________ Reading After Test: ________________
01
02
03
04
05
06
07
08
09
10
11
Check cold engine operation ...........................................
Check engine operation during warm-up .........................
Check engine at normal operating temperature ..............
Check clutch*/transmission operation..............................
Check brake and parking brake operation .......................
Check steering operation and off-center/vehicle
pull/flutter .........................................................................
Inspect for abnormal noise and vibration .........................
Inspect for squeaks and rattles ........................................
Check front and rear* heater and A/C operation..............
Check cruise control operation* ......................................
Set/calibrate compass* (see page 2) ..............................
FINAL INSPECTION AND CLEANING
01 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer).......
02 Verify floor mat application and install using
retaining clips* ...............................................................
03 Visually inspect all interior parts for installation,
damage, fit, dirt, etc. ........................................................
04 Remove Rapgard™ and clear protective bumper film*....
05 Wash and clean vehicle...................................................
06 Inspect paint finish for scratches, chips, rust, dents,
damage, etc. ....................................................................
07 Inspect exterior body parts for proper installation,
damage, rust, etc. ............................................................
08 Place oil change sticker on inside of windshield, top
left corner ........................................................................
09 Place Owner’s Guide and first aid kit portfolio*
in glove box ....................................................................
10 Perform Techstream Health Check ................................
11 Install front* and rear license plates (see page 2) ...........
COMMENTS:
Completion and retention of this form is required to comply with Toyota’s Warranty Policy.
TECHNICIAN’S SIGNATURE
SERVICE MANAGER’S SIGNATURE
NAME (PLEASE PRINT)
NAME (PLEASE PRINT)
Date
Dealer Name
Dealer Code
We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.
Vehicle Identification Number (Sticker)
SHORT PIN INSTALLATION
To minimize battery discharge the Short Pin has been removed and is stored in the engine compartment relay block.
Install the Short Pin and confirm all related DTCs (B1650 and B1794) are cleared.
If any DTCs besides DTC B1650 and B1794 remain, repair the applicable system according to the Repair Manual.
NOTE
Removing the Short Pin cuts off the power sources
relating to the dome, radio No. 1, ECU-B, and CRT fuses.
1
The Short Pin does NOT function as a fuse, so only install it
in the position shown.
2
If the vehicle is stored in the dealership for a long period of
time after PDS, disconnect the negative (–) battery terminal
to prevent battery discharge. Refer to Service Bulletin No.
PG001-06, “Battery Maintenance for In-Stock Vehicles &
Pre-Delivery,” for battery maintenance information.
3
1 Underside of Relay Block Cover
2 Short Pin Storage Location
3 Install Short Pin Here
TIRE PRESSURE WARNING SYSTEM (TPWS) INITIALIZATION
Refer to the Repair Manual for the Initialization procedure. Please note the spare tire does not have a TPWS sensor.
Remove the ID number labels that are attached to each wheel and discard.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature, perform a
Health Check using Techstream and select the “Compensation Tire Pressure” checkbox. Compensation pressures will be
displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold.
COMPASS CALIBRATION
Refer to the Repair Manual for the Calibration procedure for vehicles equipped with a compass in the rear view mirror.
NOTE
• Do NOT perform calibration of the compass in a place where the Earth’s magnetic field is subject to interference
(underground parking, under a steel tower, between buildings, roof parking, near a railroad crossing, near a large
vehicle, etc.).
• During calibration, do NOT operate electric systems (moon roof, power windows, etc.) as they may interfere with
the calibration.
FRONT* AND REAR LICENSE PLATE INSTALLATION
The following procedure is recommended for front and rear license plate installation on Tacoma vehicles.
Front Installation Procedure
Rear Installation Procedure
1. Align the holes on the license plate with the dimples on
the bumper.
2. Install 2 self-tapping screws through the license plate
and into the front bumper at the dimples.
1. Align the holes on the license plate with the holes on
the bumper.
2. Install 2 self-tapping screws through the license plate
and into the holes in the rear bumper.
Length: 16.0 – 24.0 mm (0.63 – 0.94 in.)
Diameter: 6.0 mm (0.24 in.)
Length: 16.0 mm – 18.0 mm (0.63 in. – 0.71 in.)
Diameter: 6.0 mm (0.24 in.)
NOTICE
• Do NOT pre-drill holes into the bumper.
• Do NOT overtighten the self-tapping screws.
3
2
4
1
1 Dimples
2 Length
3 Diameter
4 Installation Holes