T-SB-0073-14

LAND CRUISER
01 Install Short Pin (see page 2) ..........................................
FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse; turn
on lights and rear defogger. Unlock doors; release fuel door.
01
02
03
04
05
06
07
08
09
10
11
12
Check dome, courtesy, map, and sun visor lights* ..........
Check warning/indicator lights, gauges, and horn ...........
Check windshield wipers and washers ............................
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights ..............................
Check inside/outside rear view mirror operation/
adjustment .......................................................................
Check cigarette lighter* and power outlets ......................
Check audio/navigation*/backup camera* systems and
set clock .........................................................................
Install shift-lock override button cover ............................
Check sliding roof* .........................................................
Check Rear Seat Entertainment system operation* .......
Check Curtain Shield Airbag Roll Sensing switch & light*
Confirm Automatic Door Lock (ADL) function .................
WALKAROUND INSPECTION
Start at left front door. Check window and door lock operation (from master power
switch, if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks.
01
02
03
04
05
06
07
08
09
10
Check Smart Key System .............................................
Check window operation .................................................
Check that engine starts with all keys .............................
Check that child safety door locks are in normal
(unlocked) position ..........................................................
Check seats and seat belt operation ...............................
Check rear defogger/rear view mirror defogger* .............
Check side marker, tail, backup, and license plate lights
Check luggage compartment light and trim appearance .
Check jack and tool installation ......................................
Check headlight aim ........................................................
UNDER HOOD
01
02
03
04
05
Check engine oil level ......................................................
Check brake and power steering fluid levels ...................
Check engine coolant level ..............................................
Check windshield washer fluid level ...............................
Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading: ___________%) .....
06 Inspect for fuel, oil, coolant, and other fluid leaks ............
* Inspect or install when equipped/required.
Adjust/
Repair
UNDER VEHICLE (ON HOIST)
August 2014
OK
OK
BEFORE INSPECTION
Adjust/
Repair
2015 PRE-DELIVERY SERVICE CHECK SHEET
01 Remove disc brake anti-rust covers/anti-corrosion
wheel film* ......................................................................
02 Inspect tires for defects/damage and adjust spare tire
air pressure ....................................................................
03 Activate and Initialize Tire Pressure Warning System
(TPWS) (see page 2) ......................................................
04 Install wheel covers/caps/spare tire wheel covers*..........
05 Inspect for fuel, oil, coolant, and other fluid leaks . ..........
06 Inspect under the vehicle for damage, rust, etc. ..............
07 Visually check bolts and nuts on chassis and powertrain
for looseness ...................................................................
08 Install rubber body plugs* ...............................................
ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.
Enter Odometer Reading
Reading Before Test: _______________ Reading After Test: ________________
01
02
03
04
05
06
07
08
09
10
11
Check cold engine operation ...........................................
Check engine operation during warm-up .........................
Check engine at normal operating temperature ..............
Check automatic transmission operation ........................
Check brake and parking brake operation .......................
Check steering operation and off-center/vehicle
pull/flutter .........................................................................
Inspect for abnormal noise and vibration .........................
Inspect for squeaks and rattles ........................................
Check front and rear* heater and A/C operation .............
Check cruise control operation* .......................................
Check front seat heater/ventilation operation* ................
FINAL INSPECTION AND CLEANING
01 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer).......
02 Visually inspect all interior parts for installation,
damage, fit, dirt, etc. ........................................................
03 Verify floor mat application and install using
retaining clips* ...............................................................
04 Verify green light is illuminated on SOS (Safety Connect)
button* ............................................................................
05 Remove Rapgard™ and clear protective bumper film*....
06 Wash and clean vehicle ...................................................
07 Inspect paint finish for scratches, chips, rust, dents,
damage, etc. ....................................................................
08 Inspect exterior body parts for proper installation,
damage, rust, etc. ............................................................
09 Place oil change sticker on inside of windshield, top
left corner ........................................................................
10 Place Owner’s Guide & first aid kit portfolio* in glove box
11 Perform Techstream Health Check ................................
12 Install roof rack cross bars and leg covers ................
13 Install front license plate* (see page 2) ...........................
14 Install towing wire harness connector (see page 2) ........
15 Install receiver towing hitch cap .......................................
Completion and retention of this form is required to comply with Toyota’s Warranty Policy.
TECHNICIAN’S SIGNATURE
SERVICE MANAGER’S SIGNATURE
NAME (PLEASE PRINT)
NAME (PLEASE PRINT)
Date
Dealer Name
Dealer Code
We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.
Vehicle Identification Number (Sticker)
SHORT PIN INSTALLATION
To minimize battery discharge the Short Pin has been removed and is stored in the engine compartment relay block.
1
NOTE
 The Short Pin does NOT function as a fuse, so only install it in the position shown.
 If the vehicle is stored in the dealership for a long period of time after PDS, disconnect
the negative (–) battery terminal to prevent battery discharge. Refer to Service Bulletin
No. PG001-06, “Battery Maintenance for In-Stock Vehicles & Pre-Delivery,” for battery
maintenance information.
1 Short Pin Storage Location
2 Install Short Pin Here
2
TIRE PRESSURE WARNING SYSTEM (TPWS) ACTIVATION AND INITIALIZATION
Activation Procedure
1. Connect Techstream to DLC3.
2. Cycle the IG switch to the “IG-ON” position and check that the Low Tire Pressure Warning Light blinks for 1 minute and then
remains illuminated.
3. Press or remove the valve core to reduce the tire inflation pressure rapidly by 6 psi (0.4 kgf/cm2, 40 kPA), or more, within 30 seconds.
4. Using Techstream, check for DTCs (C2111-C2115). If no DTCs are stored, continue to step 5. If these DTCs are stored, repeat step 3.
NOTE
If DTCs C2111-C2115 are present after repeating step 3, lift the vehicle and rotate each tire so that the tire pressure warning
valve/sensor is at the top of the wheel well. Then repeat step 3.
5. Press the “DISP” switch on the steering wheel and check that the tire pressures of all 5 tires are displayed on the
multi-information display.
NOTE
 The tire pressure display is NOT shown until all tire pressure warning valve/sensors are activated.
 If “Check Tire Pressure System” or “CHECKING” is displayed, repeat step 3. If step 3 is performed and the tire pressures
are still NOT displayed, lift the vehicle and rotate each tire so that the tire pressure valve/sensor is at the top of the wheel well
(in the 12 o’clock position). Then repeat step 3.
 If the above steps are performed and the multi-information display does NOT show the tire pressure, refer to the Repair Manual.
Initialization Procedure
Refer to the Repair Manual for Initialization Procedure.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature, perform a Health
Check using Techstream and select the “Compensation Tire Pressure” checkbox. Compensation pressures will be displayed on the
Health Check results screen. Adjust the tire pressure when the tires are cold.
FRONT LICENSE PLATE INSTALLATION*
Front License Plate
1. Align the holes on the license plate to the dimples on the
front bumper.
2. Using 2 self-tapping screws, install the front license plate on
the front bumper.
NOTICE
 Do NOT pre-drill holes into the bumper.
 Do NOT overtighten the self-tapping screws.
TOWING WIRE HARNESS INSTALLATION
The towing wire harness connector set is loaded in the vehicle at
the assembly plant.
1. Connect the frame wire harness and the towing wire
harness connector.
A. Remove the water resistant caps from the 2 frame wire
harness connectors.
B. Connect the 2 frame wire harness connectors and
2 towing wire harness connectors.
2. Install the towing wire harness assembly bracket to the frame
bracket with the 2 bolts.
Torque: 19.5 N*m (199 kgf*cm, 14 ft*lbf)
Use non-corroding selftapping screws with the
following dimensions.
Length: 16.5 — 20.0 mm
(0.65 — 0.79 in.)
Diameter: 6.0 mm (0.24 in.)
1
1 Self-tapping Screws