SP 284-064, Engi
Service Bulletin Details
Public Details for: SP 284-064, Engi
Software updates with enhancements are available for the engine control module (ecm) for volvo d11j, d13j and d16j engines with us2016 emission level on vehicles built from january 4, 2016 to may 6, 2016.
- 2017 -
Models from 2017
2017 VOLVO VAH |
2017 VOLVO VHD |
2017 VOLVO VN |
Volvo Trucks North America Greensboro, NC USA Service Program Trucks Date 9.2016 Group No. 284 064 Release Page 01 1(7) Engine Control Module (ECM), Software Updates D11J, D13J, D16J VAH, VHD, VN SP 284-064, Engine Control Module (ECM), Software Updates (September 2016) Information Software updates with enhancements are available for the Engine Control Module (ECM) for VOLVO D11J, D13J and D16J engines with US2016 emission level on vehicles built from January 4, 2016 to May 6, 2016. Software updates address the following. • USA79324 Campaign needed to update trucks shipped to California for inducement strategy on meeting CARB Regulations, and implement Selective Catalytic Reduction (SCR) inducement (5mph) for NOx conversion. PV729-SP284-064 Volvo Trucks North America Service Program Date 9.2016 Group No. Release 284 064 01 Required Tools Premium Tech Tool (PTT) version 2.05.23 or higher Vocom Diagnostic Connector 88890304 Communication Interface 88890300 Note: Using other interfaces may affect programming speed. Note: Check Premium Tech Tool version by clicking on Help tab and then click on “About Tech Tool”. Software Update Procedure You must read and understand the precautions and guidelines in Service Information, group 20, "General Safety Practices, Engines" before performing this procedure. If you are not properly trained and certified in this procedure, ask your supervisor for training before you perform it. DANGER Do not attempt to repair or service this vehicle without having sufficient training, the correct service literature and the proper tools. Failure to follow this could make the vehicle unsafe and lead to serious personal injury or death. 1 Park the vehicle on a level surface. 2 Apply the parking brake. 3 Place the transmission in neutral or park. 4 Install the wheel chocks. W7086748 5 Verify service program eligibility by checking service program status in VDA. 6 Connect Premium Tech Tool (PTT) to the vehicle diagnostics connector using the 16 pin OBD cable 88890304 and Communication Interface 88890300. Connect the PC to a functional LAN or modem connection and a 120 Volt AC source. Page 2(7) Volvo Trucks North America Service Program Date 9.2016 Group No. Release 284 064 01 7 Turn the ignition switch “ON”. 8 Log in to PTT and Identify Vehicle is displayed. 9 Once the vehicle has been identified, enter the Work Order Number information, then click Start Work. W2115477 10 From the Main Menu select Program and then Program Electronic Control Unit 1700-0803-39. Then click Start. W2115478 Page 3(7) Volvo Trucks North America Service Program Date 9.2016 Group No. Release 284 064 01 11 Select EMS. W2115479 12 Select Program to update the EMS with the latest software. W2115480 Page 4(7) Volvo Trucks North America Service Program Date 9.2016 Group No. Release 284 064 01 13 Certain conditions must be met to continue with programming: battery voltage above 10v, parking brake applied, and ignition key in ON position with engine not running. When all conditions have been met, click Continue to proceed with programming. W2115481 14 Select “I accept” to agree to the terms and press continue to proceed. Note: In the United States and Canada, the programing is NOT chargeable. An invoice will not be generated. W2115482 Page 5(7) Volvo Trucks North America Service Program Date 9.2016 Group No. Release 284 064 01 15 If the software is already updated, this screen opens. Select Yes to reload existing software. W2115483 16 When the programing is complete, clear any diagnostic trouble codes (DTC) and Finish Work. 17 Remove the wheel chocks. W7086759 Page 6(7) Volvo Trucks North America Service Program Date 9.2016 Group No. Release 284 064 01 Reimbursement This repair is covered by an authorized Service Program. Reimbursement is obtained via the normal claim handling process. UCHP Reimbursement Recall Status Vehicle inspected, repair not required 1- Inspected OK Vehicle repaired per instruction 2- Modified per instruction Labor Code Primary Labor Code 2841–22–09–12 0.3 hrs Time to take charge and determine campaign status 1700–16–01–01 0.3 hrs Causal Part 3092091 Parts Disposition N/A SCC Code S7110 Authorization Number N/A Expiration Date 31 - DEC - 2016 Note: Take Charge Time is not included in the Labor Code for this operation. Take charge may be eligible but can only be used once per repair visit. If vehicle is having other warranty repairs performed, take charge should be charged to the warranty repair, otherwise take charge can be charged to this service program. Page 7(7)