T-SB-0119-16
Service Bulletin Details
Public Details for: T-SB-0119-16
Tsb: 2017 pre-delivery service check sheet
- 2017 -
Models from 2017
2017 TOYOTA TUNDRA |
Tundra UNDER VEHICLE (ON HOIST) 1 Install Short Pin (see page 2) ……………..…………………. 2 Install antenna ………………………………………………… 1 Remove disc brake anti-rust covers/anti-corrosion wheel film* (remove just prior to customer delivery).…….. 2 Inspect tires for defects/damage ………………………….… 3 Initialize Tire Pressure Warning System (TPWS) (see page 2)…...................................................................... 4 Install wheel covers/caps/spare tire wheel covers* ………. 5 Inspect for fuel, oil, coolant, and other fluid leaks ………… 6 Inspect under the vehicle for damage, rust, etc …………… 7 Visually check bolts and nuts on chassis and powertrain for looseness…………………………………………………… 8 Install rubber body plugs (stored in glove box or center console)*…………………………………………....….. FUNCTIONAL OPERATION Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse; turn on lights and rear defogger. Unlock all doors, release fuel door. 1 2 3 4 5 6 7 8 9 10 11 OK BEFORE INSPECTION August 2016 Adjust\ Repair OK 2017 PRE-DELIVERY SERVICE CHECK SHEET Adjust\ Repair Market: USA Check dome, courtesy, map, and sun visor lights*………... Check warning/indicator lights, gauges, and horn.…..……. Check windshield wipers and washers….…………………… Check headlights, instrument lights, turn signals, dimmer switch, emergency flashers, and brake lights ……. Check inside/outside rear view mirror operation/adjustment*…………………………………………. Check cigarette lighter* and power outlets…………………. Check audio/navigation*/backup camera systems and set clock.……………….………………………………………. Install shift-lock override button cover ………... ……….…... Check sliding roof* ……………………………………………. Check Rear Seat Entertainment System operation*………. Check passenger airbag system cutoff switch and light* …. ROAD TEST A complete road test helps assure customer satisfaction. Drive vehicle over a variety of road surfaces and driving conditions. Check for unusual noise and driving performance. Enter Odometer Readings Reading Before Test: _______________ Reading After Test: ________________ 1 2 3 4 5 6 7 8 9 10 11 12 WALKAROUND INSPECTION Starting at the left front door, check window and door lock operation. Continue around the vehicle in a counterclockwise direction checking each door and window operation, child door locks, seat belts, interior condition, all lights, and luggage compartment contents. Finish by checking headlight aim and continue into UNDER HOOD checks. 1 Check door and door lock operation, including each wireless remote control/theft deterrent system*……………. 2 Check window operation……………………………………… 3 Check that engine starts with all keys ……………….……… 4 Check that child safety door locks are in normal (unlocked) position*…………………………………………… 5 Check seats and seat belt operation………………………... 6 Check rear defogger/rear view mirror defogger*…………… 7 Check side marker, tail, backup, cargo*, and license plate lights …………………………………………………….. 8 Check jack and tool installation………………………………. 9 Check headlight aim…………………………………………... Check cold engine operation ………………………………… Check engine operation during warm-up …………………… Check engine operation at normal operating temperature… Check transmission operation …………………………...…. Check brake and parking brake operation …………………. Check steering operation and off-center/vehicle pull/flutter Inspect for abnormal noise and vibration …………………… Inspect for squeaks and rattles ……………………………… Check front and rear* heater and A/C operation…………… Check cruise control operation* ……………………………... Check front seat heater/ventilation operation* …………….. Set/calibrate compass* (see page 2)……………………….. FINAL INSPECTION AND CLEANING 1 Remove interior protective covers, unnecessary labels, tags, etc. (Remove just before delivery to customer) ……… 2 Visually inspect all interior parts for installation, damage, fit, dirt, etc.…………………………………… ……………….. 3 Verify floor mat application and install using retaining clips*……………………………………………...... 4 Remove Rapgard™ and clear protective bumper film*…… 5 Wash and clean vehicle………………………………………. 6 Inspect paint finish for scratches, chips, rust, dents, damage, etc…………………………………………………… 7 Inspect exterior body parts for proper installation, damage, rust, etc…………………………………………………………. 8 Place oil change sticker on inside of windshield, top left corner………………………………………………………. 9 Place Owner’s Manual portfolio* in glove box………………. 10 Perform Techstream Health Check………………………….. 11 Install front license plate and mounting bracket* (see page 2) …………………………………………………… 12 Install receiver towing hitch cap*…….……………………….. UNDER HOOD 1 2 3 4 5 Check engine oil level………………………………………… Check brake and power steering* fluid levels……..……….. Check engine coolant level ………………………………….. Check windshield washer fluid level………………………… Check battery state-of-charge using Digital Battery System Analyzer (SOC Reading: ___________%) …….. 6 Inspect for fuel, oil, coolant, and other fluid leaks…………. * Inspect or install when equipped/required. Notes: Completion and retention of this form is required to comply with Toyota’s Warranty Policy. TECHNICIAN’S SIGNATURE NAME (PLEASE PRINT) Date Dealer Name SERVICE MANAGER’S SIGNATURE We hereby certify that all items on this form have been checked and corrected for proper operation as required. NAME (PLEASE PRINT) Dealer Code Vehicle Identification Number (Sticker) SHORT PIN INSTALLATION To minimize battery discharge, the short pin has been removed and is stored in the engine compartment Relay Block. Install the short pin and perform the below procedure to clear the Slip Indicator Light if it has set. Slip Indicator Light Clearing Procedure 1. Drive straight for a minimum of 3 seconds at a speed greater than 7 mph. 2. Gently maneuver through a moderate turn (steering wheel rotated at least 20 degrees) lasting for at least 4 seconds at a speed greater than 7 mph. 3. Slip Indicator Light will turn OFF when the system has been successfully initialized. NOTE Do NOT turn the steering wheel rapidly. 1 Storage Location 2 Installation Location 4. If the Slip Indicator Light remains ON, repeat steps 1 and 2. TIRE PRESSURE WARNING SYSTEM (TPWS) INITIALIZATION The Tundra is equipped with a direct-type TPWS. Each tire (including the spare) has a tire pressure warning valve/sensor that measures tire pressure. The sensors must first be activated prior to operation. Refer to the below information. Refer to the Repair Manual for the Initialization procedure. NOTE To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature, perform a Health Check using Techstream and select the “Compensation Tire Pressure” checkbox. Compensation pressures will be displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold. COMPASS CALIBRATION Some Tundra vehicles are equipped with a compass in the rear view mirror. In order for the compass to correctly indicate the direction the vehicle is heading, it must be calibrated prior to vehicle delivery. Refer to the Repair Manual for the Calibration procedure. NOTE Do NOT perform calibration of the compass in a place where the Earth’s magnetic field is subject to inferference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a railroad crossing, etc.) During calibration, do NOT operate electric systems (moon roof, power windows, etc.) as they may interfere with the calibration. FRONT LICENSE PLATE AND MOUNTING BRACKET INSTALLATION* 1. Insert the front license plate into tabs on the front license plate mounting bracket. 2. Align the installation holes on the license plate and front license plate mounting bracket with the dimples on the front bumper. 3. Screw the 2 self-tapping screws directly into the dimples to install the front license plate and front license plate mounting bracket. NOTICE Do NOT pre-drill holes into the bumper. Do NOT overtighten the self-tapping screws. HINT Tighten the self-tapping screw into the round hole side first, then tighten the other self-tapping screw into the slotted hole. 1 License Plate 2 License Plate Mounting Bracket 3 Dimples 4 Self-tapping Screws