PIP5209A
Service Bulletin Details
Public Details for: PIP5209A
- 2014 - 2013 - 2012 - 2011 - 2010 -
Models from 2014
2014 BUICK LACROSSE |
2014 CADILLAC ATS |
2014 CADILLAC CTS |
2014 CADILLAC SRX |
2014 CADILLAC XTS |
2014 CHEVROLET CAMARO |
2014 CHEVROLET EQUINOX |
2014 CHEVROLET IMPALA |
2014 GMC TERRAIN |
Models from 2013
2013 BUICK LACROSSE |
2013 CADILLAC ATS |
2013 CADILLAC CTS |
2013 CADILLAC SRX |
2013 CADILLAC XTS |
2013 CHEVROLET CAMARO |
2013 CHEVROLET EQUINOX |
2013 CHEVROLET IMPALA |
2013 GMC TERRAIN |
Models from 2012
2012 BUICK LACROSSE |
2012 CADILLAC CTS |
2012 CADILLAC SRX |
2012 CHEVROLET CAMARO |
2012 CHEVROLET EQUINOX |
2012 CHEVROLET IMPALA |
2012 GMC TERRAIN |
Models from 2011
2011 BUICK LACROSSE |
2011 CADILLAC CTS |
2011 CADILLAC SRX |
2011 CHEVROLET EQUINOX |
2011 GMC TERRAIN |
Models from 2010
2010 BUICK LACROSSE |
2010 CADILLAC CTS |
2010 CADILLAC SRX |
2010 CHEVROLET EQUINOX |
2010 GMC TERRAIN |
Bulletin No.: PIP5209A Date: Aug-2014 Subject: P00C6 P228C Diagnostic Assistance Models: 2010-2014 Buick LaCrosse 2010-2014 Cadillac CTS SRX 2013-2014 Cadillac ATS XTS 2012-2014 Chevrolet Camaro Impala 2010-2014 Chevrolet Equinox 2010-2014 GMC Terrain Equipped with HFV6 engine RPO codes LF1, LFW, or LFX This PI was superseded to update Model Years. Please discard PIP5209. The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI. Condition/Concern A vehicle may come in with DTC P00C6 and/or P228C set. If normal SI diagnostics do not lead to a repair, before any component replacements please follow the recommendations below. Recommendation/Instructions Re-check the terminals at the ECM for fit and tension as well as the crimp to wire connection. Terminals to inspect in the E39 and E39A controllers are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Connector x3 terminals 16 and 32 for the high pressure fuel pump. Note: As little as 2 Ω on either circuit can cause these DTCs to set If any concerns are found, replace the affected terminals and verify the vehicle is repaired Warranty Information For vehicles repaired under warranty use: Labor Code Description Labor Time 5430840 Terminal Replacement Use Published Labor Operation Time Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed. GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information. 1 WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION 2