PIT5063C

Bulletin No.: PIT5063C
Date: Aug-2013
Subject:
Diagnostic Tip - Service Steering Message or Service Stability Message
Models:
2010 - 2014 Buick LaCrosse (with RPO NJ1)
2012 - 2014 Buick Regal (with RPO NJ1)
2012 - 2014 Buick Verano
2010 - 2014 Chevrolet Cruze, Equinox
2011 - 2014 Chevrolet Volt
2013 - 2014 Chevrolet Malibu
2014 Chevrolet Impala (with RPO NJ1)
2010 - 2014 GMC Terrain
With one or more of the following DTC C056E Sym 42 C0569 Sym 3A C0710 Sym 71 or 00
This PI was superseded to update model list and add warranty info. Please discard PIT5063B.
The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.
Condition/Concern
Customer may comment on one or both of the following:
* Service Steering Message
* Service Stability Message
The Technician may find DTC C056E Sym 42 calibration data set not programmed. The DTC C0569 Sym 3A sets after a new steering gear assembly was
installed.
Recommendation/Instructions
Important: Before diagnosing DTC C056E Sym 42 or DTC C0569 Sym 3A: If a steering angle sensor DTC C0710 Sym 71 (invalid serial data) or 00 is set, the
C0710 must be fixed first in order to learn steering angle in the EBCM and PSCM or the TIS2WEB steering gear “set-up” will fail. When a Steering Angle Sensor
(SAS) on the chassis bus fails, a C0710 Sym 71 or 00 sets. The C0710 will be found in two modules: the EBCM and the PSCM (if equipped with electric
steering).
The SAS sensor/module can store C056D Sym 00 (internal hardware fault), diagnose this code first. The Power Steering Gear assembly does not have an
internal Steering Angle Sensor. Rather, it uses the steering angle sensor data from the EBCM. The Power steering control module learns the SAS that is on the
Chassis Bus from the EBCM through high speed LAN.
DTC C056E Sym 42 or C0569 Sym 3A: The Power Steering Control Module (PSCM) can set DTC C056E Sym 42 when a steering gear assembly was replaced
without SPS programming.
DTC C0569 Sym 3A can set from a previous motor/module or steering gear replacement that was not previously programmed correctly or has internal module
data missing. DTC C0569 Sym 3A can also set if an incorrect steering gear assembly part number was installed. Below are some examples related to the
codes that set:
Example 1: Previous repair from a body shop with a steering gear replacement without SPS programming or Set-up. The steering will work normal with no
service steering message. This allows the technician time to set the wheel alignment. After some time the (PSCM) Power Steering Control Module will set a
latched DTC of C056E symptom 42 (calibration data set not programmed) resulting in a Service Steering Message. The Service information will instruct to
program the PSCM using TIS2WEB and then Set-up. During Set-up it fails because too much time has passed without software programming and set up. If
1
using GDS performing the soft-stop learn function will appear to be completed but the DTC C056E 42 will not clear from the PSCM. At this point the complete
steering gear assembly must be replaced and programmed.
Example 2: If a “Prepare module for removal” was performed from a Power steering gear assembly that contained C056E 42 from a non programmed module
and a newly installed steering gear assembly was just installed and after SPS programming the DTC C0569 3A set. Confirm that the correct steering gear part
number was installed. At this point contact the TCSC (Techline) for special programming instructions.
Important: The only time a "Prepare Module for Removal” is performed is when a motor/module (Power Pack) is replaced for motor fault DTC C0475.
Note: When a new steering gear is replaced, perform the following steps:
1.
Install the steering gear assembly
2.
Set the alignment toe
3.
3. SPS program the EPS module using TIS2WEB
4.
Perform the EPS Set-up Procedure using TIS2WEB (this will learn SAS from the EBCM and learns end-stop).
Warranty Information
The correction for this concern may be one of several repairs described above. For vehicles repaired under warranty, please use the appropriate warranty
labor operation based on the actual cause and repair.
Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the
remaining steps do not need to be performed.
GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may
occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools,
safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that
your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information.
WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION
2