Service Bulletin

Service Bulletin
December 17, 2014
14-006
ATB 50873-01155 REV2(1411)
Low Tire Pressure/TPMS Indicator Is On with VSA DTC 151-11
Supersedes 14-006, dated November 28, 2014, to revise the information highlighted in yellow.
AFFECTED VEHICLES
Year
Model
2014
CR-V
Trim
VIN Range
ALL
ALL
REVISION SUMMARY
• Affected vehicles were updated.
• Under WARRANTY CLAIM INFORMATION, the flat rate time and the operation number were change.
• Under SOFTWARE INFORMATION, the software was updated.
SYMPTOM
The Low Tire Pressure/TPMS indicator is on with VSA DTC 151-11 (low tire pressure threshold refinement) and the tire
pressures were properly set to the driver’s doorjamb label.
POSSIBLE CAUSES
A second software update is needed for different driving conditions.
CORRECTIVE ACTION
Update the VSA modulator-control unit software.
SOFTWARE INFORMATION
NOTE: Unnecessary or incorrect repairs resulting from a failure to update the MVCI or HDS are not covered under
warranty.
MVCI Control Module (CM) Update:
Application (FW) Version: 3.01.40
Database Date: 12-Nov-2014
HDS Software Version:
3.015.023 or later
Before beginning the repair, make sure that both the HDS and the MVCI are updated as listed above.
Do only the update listed in this service bulletin.
Page 1 of 3
CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools,
equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you
should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information
applies, contact an authorized Honda automobile dealer.
© 2014 American Honda Motor Co., Inc. – All Rights Reserved
Check that the MVCI indicates the applicable program ID listed below (or a later program ID) as the Recommended
Update when the update begins.
If the MVCI displays This vehicle does not need an update at this time during the update, check the MVCI Control
Module update application is correct as shown above. If the software is correct, the vehicle software has been updated.
For more information about updating the HDS, the MVCI, and vehicle systems, refer to Service Bulletin 01-023,
Updating Control Units/Modules.
Year/Model
Program ID (or later)
Program P/N (or later)
2014 LX, AWD
0GA140
57114-T0G-A14
2014 EX, EXL, AWD
0GA240
57114-T0G-A24
2014 LX, 2WD
0HA140
57114-T0H-A14
2014 EX, EXL, 2WD
0HA240
57114-T0H-A24
WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation Number
Description
Flat Rate Time
Template ID
Failed Part Number
4135A0
Update the VSA modulatorcontrol unit.
0.4 hr
14-006A
P/N 57111-T0G-A22
Defect Code:
08001
Symptom Code: 04201
Skill Level:
Repair Technician
REPAIR PROCEDURE
1. Connect a fully charged jumper battery to the vehicle and leave it connected during the entire update procedure to
maintain a steady voltage.
2. Apply the parking brake and make sure the headlights are turned off.
3. Turn the ignition to ON and turn off all accessories.
4. Connect the MVCI to the vehicle.
5. Press the ENTER button on the MVCI to see the User Config menu. Select CM Update Mode, then press ENTER.
6. Select Reprogramming, then press ENTER.
7. When the CM Update Mode software screen appears, press ENTER to continue.
NOTE: The FW VER must be 3.01.40 or later and Database Update must be 12 Nov 2014 or later.
8. When the Select System screen appears, select ABS/VSA, then press ENTER.
NOTE:
•
•
If the VSA update is the only one available, it will automatically go to the VSA selections.
For program ID and program part number, see SOFTWARE INFORMATION.
Page 2 of 3
9. Scroll down and select Running change. If YES, press ENTER. Press ENTER again to start reprogramming.
10. While the MVCI updates the vehicle, set the tire pressures to the cold inflation values listed on the driver’s
doorjamb label.
11. Once the update is complete, follow the screen prompts to turn the ignition to OFF, then to ON again when
indicated.
NOTE: If there is an error during the update, keep the ignition turned to ON and press ENTER to display the error
code. Record the code and restart the update. If the error code comes back, refer to the CM Update Error Code
Table in the MVCI User Guide for more information.
12. When the MVCI displays VSA Sensor Neutral Position Memorization is required after the completion of the
update, scroll down and press ENTER.
13. Go to VSA SENSOR NEUTRAL POSITION MEMORIZATION PROCEDURE.
VSA SENSOR NEUTRAL POSITION MEMORIZATION PROCEDURE
1. Connect the HDS and make sure the software version is 3.15.023 or later.
2. Select Honda Systems, ABS/TCS/VSA, Adjustment, and All Sensors, then follow the screen prompts
3
Once completed, exit the VSA system. Turn the ignition to OFF, then back to ON. Go to EPS STEERING ANGLE
SENSOR NEUTRAL POSITION CLEAR PROCEDURE.
EPS STEERING ANGLE SENSOR NEUTRAL POSITION CLEAR PROCEDURE
1. Go to EPS on the HDS.
2. Select Adjustment, Steering Angle Sensor Value Clear, and follow the screen prompts
3. Turn the ignition to OFF, then back to ON. Go to SPECIALTPMS CALIBRATION USED ONLY AFTER
SOFTWARE UPDATE.
SPECIAL TPMS CALIBRATION USED ONLY AFTER SOFTWARE UPDATE
NOTE: If the tire pressures were not already set, make sure they are set to the cold inflation values listed on
the driver’s doorjamb label.
1
Turn the ignition to ON.
2
Press and hold the TPMS button until the Low Tire Pressure/TPMS indicator blinks twice, then release the button.
3
Repeat step 2 two more times.
4
Disconnect the jumper battery, start the vehicle, and verify that the VSA and the Low Tire Pressure/TPMS indicators
come on and go off.
5
Turn the ignition to OFF and disconnect the HDS.
NOTE: Customer normal drive will finish calibration.
END
Page 3 of 3