A16103

Service Bulletin
November 11, 2016
16-103
05269 Version 2
Emissions Recall: 2017 HR-V PCM Incorrectly Adjusts Air to Fuel Ratio
Supersedes 16-103, titled Emissions Recall: 2017 HR-V Primary Converter and AF Sensor Deterioration, dated
November 10, 2016 to include SOFTWARE INFORMATION, WARRANTY CLAIM INFORMATION, and REPAIR
PROCEDURE.
AFFECTED VEHICLES
Year
Model
2017
HR-V
Trim
ALL
VIN Range
Check the iN VIN status for eligibility
BACKGROUND
There is an internal programming issue with the PCM. Under certain hot restarting and driving conditions, the air to fuel
ratio control may not compensate properly.
CUSTOMER NOTIFICATION
Owners of affected vehicles will be sent a notification of this campaign.
Do an iN VIN status inquiry to make sure the vehicle is shown as eligible.
Some vehicles affected by this campaign may be in your new or used vehicle inventory. Repair these vehicles before
they are sold.
CORRECTIVE ACTION
Update the PGM-FI software.
WARRANTY CLAIM INFORMATION
Operation
Number
Description
Flat
Rate
Time
Defect
Code
Symptom
Code
Template
ID
Failed Part Number
3115A0
Update the PGM-FI
software.
0.2 hr
6EM00
KD100
16-103A
37805-51M-C02
A
Do the idle-learn
procedure.
0.1 hr
B
Do the CKP procedure.
0.1 hr
CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools,
equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and
you should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this
information applies, contact an authorized Honda automobile dealer.
© 2016 American Honda Motor Co., Inc. – All Rights Reserved
Page 1 of 4
SOFTWARE INFORMATION
NOTE: Unnecessary or incorrect repairs resulting from a failure to update the i-HDS or MVCI are not covered under
warranty.
i-HDS Software Version: 1.001.011 or later
J2534 Software Information:
PC Application Version 1.0.1.15 or later
Database update 09-NOV-2016 or later
Before beginning the repair, make sure that both the i-HDS and J2534 software are updated as listed above.
Do only the update listed in this service bulletin.
You cannot apply the updates with the MVCI as a standalone tool. To update the vehicle you must use the MVCI or
the DST-i interface in conjunction with the J2534 Rewrite PC application on the i-HDS.
For more information about updating the i-HDS, the MVCI, and vehicle systems, refer to Service Bulletin 01-026,
Updating Control Units/Modules.
Trim
Software
Program ID (or later)
Program P/N (or later)
System
2017 HR-V LX (2WD) (M/T)
PGM-FI
1MC020
37805-51M-C02
2017 HR-V EX (2WD) (M/T)
PGM-FI
1MC120
37805-51M-C12
2017 HR-V LX (2WD) (CVT)
PGM-FI
1MC520
37805-51M-C52
2017 HR-V EX, EX-L (2WD) (CVT)
PGM-FI
1MC620
37805-51M-C62
2017 HR-V LX (AWD) (CVT)
PGM-FI
1MC720
37805-51M-C72
2017 HR-V EX, EX-L (AWD)
PGM-FI
1MC820
37805-51M-C82
(CVT)
REPAIR PROCEDURE
NOTE:
• You can’t update the vehicle using the MVCI as a standalone tool.
• Do not use the MongoosePro VCI tool.
• Make sure the 12-volt battery is fully charged before starting an update.
• Connect a fully charged jumper battery to the vehicle, and leave it connected during the entire procedure to
maintain steady voltage.
• Never turn the ignition to OFF or ACCESSORY during the update. If there is a problem with the update, leave the
ignition turned to ON.
• To prevent PCM damage, do not operate anything electrical (headlights, audio system, brakes, A/C, power
windows, door locks, etc.) during the update.
• If you see the following Error Display, check that you are using the correct tool (MVCI or DST-i) with the i-HDS.
Page 2 of 4
To change this, click on either of the SETTING selection buttons at the bottom of the J2534 initial screens as
shown.
1. Update the PGM-FI software by selecting the i-HDS Disagnostic System icon. Refer to Service Bulletin
01-026, Updating Control Units/ Modules.
NOTE: Do not use the Rewrite icon on your desktop.
2. Select J2534 Rewrite.
3. Confirm the software is the same or later as listed in SOFTWARE INFORMATION.
Page 3 of 4
4. Select Start, then follow the screen prompts.
NOTE:
• Don’t enter a bulletin number.
• If you receive a message that the vehicle has been already updated or that no update is available, check the
PGM-FI data list. The header should indicate one of the following numbers (or later).
37805-51M-C02
37805-51M-C12
37805-51M-C52
37805-51M-C62
37805-51M-C72
•
37805-51M-C82
If the program part numbers do not match those listed above, the i-HDS software needs to be reinstalled.
Contact the Special Tools Hotline at 800-346-6327 for assistance.
5. Do the idle-learn procedure. Refer to the service information.
6. Do the CKP pattern learn procedure. Refer to the service information.
7. For California residents only: Fill out a Vehicle Emissions Recall – Proof of Correction certificate, and use KD1 as
the recall number. Give the certificate to your customer, and advise him or her to keep it as proof that the product
update was completed. Your customer will need to submit this certificate to the DMV only if the DMV requests it. If
you need more certificates, use reorder number Y0657.
END
Page 4 of 4