A17-036
Service Bulletin Details
Public Details for: A17-036
Service bulletin - the mil comes on with dtc P0430 (front bank catalyst system efficiency below threshold [bank 2]). The pcm software may misinterpret sensor inputs as a deteriorated catalytic converter.
Models from 2018
2018 HONDA ODYSSEY |
Models from 2017
2017 HONDA PILOT |
2017 HONDA RIDGELINE |
Models from 2016
2016 HONDA PILOT |
Service Bulletin 17-036 September 13, 2017 07329 Version 3 MIL Comes On with DTC P0430 (Front Bank Catalyst System Efficiency Below Threshold [Bank 2]) Supersedes 17-036, dated August 16, 2017; to revise the section highlighted in yellow AFFECTED VEHICLES Year Model 2016–17 Pilot 2018 Odyssey 2017 Ridgeline Trim ALL ALL ALL VIN Range ALL ALL ALL REVISION SUMMARY Added a step under REPAIR PROCEDURE. SYMPTOM The MIL comes on with DTC P0430 (front bank catalyst system efficiency below threshold [Bank 2]). POSSIBLE CAUSES The PCM software may misinterpret sensor inputs as a deteriorated catalytic converter. CORRECTIVE ACTION Update the PGM-FI software. WARRANTY CLAIM INFORMATION The normal warranty applies. Operation Number 1255C1 B Description Flat Rate Time Update the PGM-FI software. 0.2 hr Confirm 9AT software update only - add. 0.1 hr Defect Code 03214 Symptom Code Template ID 03217 17-036B Failed Part Number 37805-RLV-315 NOTE: Use the warranty information below only if the 9AT software update was required. Operation Number 1255C1 B C Description Flat Rate Time Update the PGM-FI software. 0.2 hr Confirm 9A/T software update only - add. 0.1 hr Do the 9A/T software update - add. 0.1 hr Defect Code 03214 Symptom Code 03217 Template ID 17-036C Failed Part Number 37805-RLV-315 Skill Level: Repair Technician CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer. © 2017 American Honda Motor Co., Inc. – All Rights Reserved Page 1 of 9 SOFTWARE INFORMATION NOTE: Unnecessary or incorrect repairs resulting from a failure to update the i-HDS or MVCI are not covered under warranty. i-HDS Software Version: 1.003.015 or later J2534 Software Information: PC Application Version 1.1.0.2 or later Database update 12-JUL-2017 or later Before beginning the repair, make sure that both the i-HDS and J2534 software are updated as listed above. Do only the update listed in this service bulletin. You cannot apply the updates with the MVCI as a standalone tool. To update the vehicle, you must use the DST-i interface or MVCI in conjunction with the J2534 Rewrite PC application on the i-HDS. For more information about updating the i-HDS, the MVCI, and vehicle systems, refer to Service Bulletin 01-023, Updating Control Units/Modules. Year/Model 2016 Pilot 2017 Pilot Program ID (or later) LX 2WD EX 2WD EX-L 2WD EX-L (NAVI) 2WD EX-L (RES) 2WD LX 4WD EX 4WD EX-L 4WD EX-L (NAVI) 4WD EX-L (RES) 4WD EX (Sensing) 2WD EX-L (Sensing) 2WD EX (Sensing) 4WD EX-L (Sensing) 4WD *TRG (9A/T) 2WD *TRG (9A/T) 4WD *Elite (9A/T) 4WD LX 2WD EX 2WD EX-L 2WD EX-L (NAVI) 2WD EX-L (RES) 2WD LX 4WD EX 4WD EX-L 4WD EX-L (NAVI) 4WD EX-L (RES) 4WD EX (Sensing) 2WD EX-L (Sensing) 2WD EX (Sensing) 4WD EX-L (Sensing) 4WD *TRG (9A/T) 2WD *TRG (9A/T) 4WD *Elite (9A/T) 4WD Program P/N (or later) LV3150 37805-RLV-315 LV3160 37805-RLV-316 LV3170 37805-RLV-317 LV3180 37805-RLV-318 LV4060 37805-RLV-406 LV4070 37805-RLV 407 LVC030 37805-RLV-C03 LVC130 37805-RLV-C13 LVC230 37805-RLV-C23 LVC330 37805-RLV-C33 LVC430 37805-RLV-C43 LVC530 37805-RLV-C53 Page 2 of 9 2018 Odyssey 2017 Ridgeline *LX *EX *EX-L *EX-L (NAVI, RES) TRG Elite RTL 4WD RTL-T 4WD Sport 4WD Black 4WD RTL-E 4WD RT 2WD RTL 2WD RTL-T 2WD Sport 2WD MRA040 37805-5MR-A04 MRA250 37805-5MR-A25 MRA750 37805-5MR-A75 MJA560 37805-5MJ-A56 MJA760 37805-5MJ-A76 MJA060 37805-5MJ-A06 * Confirm that the 9A/T software is up-to-date REPAIR PROCEDURE NOTE: • You cannot update the vehicle using the MVCI as a standalone tool. • Do not use the MongoosePro VCI tool. • Make sure the 12-volt battery is fully charged before starting an update. • Connect a fully charged jumper battery to the vehicle, and leave it connected during the entire procedure to maintain steady voltage. • Never turn the ignition to OFF or ACCESSORY during the update. If there is a problem with the update, leave the ignition turned to ON. • To prevent PCM damage, do not operate anything electrical (headlights, audio system, brakes, A/C, power windows, door locks, etc.) during the update. • If you see the following Error Display, check that you are using the correct tool (MVCI or DST-i) with the i-HDS. Page 3 of 9 To change this, click on either of the SETTING selection buttons at the bottom of the J2534 initial screens as shown. 1. Update the PGM-FI or A/T software by selecting the i-HDS Diagnostic System icon. Refer to service bulletin 01-026, Updating Control Units/Modules. NOTE: Do not use the Rewrite icon on your desktop. 2. Select J2534 Rewrite. Page 4 of 9 3. Confirm the software is the same or later as listed in SOFTWARE INFORMATION. 4. Select Start, then follow the screen prompts. NOTE: • Do not enter a bulletin number. • If you receive a message that the vehicle has been already updated or that no update is available, check the PGM-FI Data List. The header should indicate one of the following numbers (or later): • 37805-RLV-315 37805-RLV-316 37805-RLV-317 37805-RLV-318 37805-RLV-406 37805-RLV-407 37805-RLV-C03 37805-RLV-C13 37805-RLV-C23 37805-RLV-C33 37805-RLV-C43 37805-RLV-C53 37805-5MR-A04 37805-5MR-A25 37805-5MR-A75 37805-5MJ-A56 37805-5MJ-A76 37805-5MJ-A06 If the program part numbers do not match those listed above, the i-HDS software needs to be reinstalled. Contact the Special Tools Hotline at 800-346-6327 for assistance. Page 5 of 9 Confirm 9AT Software is Up to Date 1. Select J2534 Rewrite. 2. Select Start. 3. Select Start. Page 6 of 9 4. Select Next. 5. Select Next. Page 7 of 9 6. Select Next, and a loading screen will appear. Page 8 of 9 7. Check if TCM appears under System Selection? • • If it appears, choose Select then ENTER on the next screen to update the TCM software. If it does not appear, the TCM software is up to date. 8. Do the PCM idle learn procedure. Refer to the service information. END Page 9 of 9