NTB17-073

Classification:
Reference:
AT17-006
Date:
NTB17-073
July 6, 2017
2017 ROGUE; PARK LIGHT ON SHIFT ASSEMBLY REMAINS ON
LONGER THAN 5 MINUTES AFTER SHIFTED TO PARK
APPLIED VEHICLE:
APPLIED VIN
APPLIED DATE:
2017 Rogue (T32) Without Intelligent Key
Built on or between:
2WD - JN8AT2M(*)(*)HW 130101 and JN8AT2M(*)(*)HW 152254
AWD - JN8AT2M(*)(*)HW 000101 and JN8AT2M(*)(*)HW 026247
AWD - JN8AT2M(*)(*)HW 250001 and JN8AT2M(*)(*)HW 269072
Built on or before April 7, 2017
IF YOU CONFIRM
After the vehicle has been shifted into Park
(P), the ignition switch is OFF and the doors
are closed:

P indicator light (Figure 1) on the shift
assembly does not go OFF after 5
minutes.
And

Applied VIN begins with “JN8”.
Figure 1
ACTION

Adjust the key interlock cable.
NOTE: Nissan vehicle warranty does not cover incidents due to lack of vehicle
maintenance and/or physical damage. Refer to New Vehicle Limited Warranty in the
Nissan Assurance Products Resource Manual (APRM) for warranty coverage
guidelines and complete information regarding warranty coverage.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/5
SERVICE PROCEDURE
Key Interlock Cable Adjustment
1. Remove the center console finisher to
gain access to the key interlock cable
adjuster shown in Figure 2.
 Refer to the Electronic Service
Manual (ESM), section IP –
Instrument Panel, for removal and
installation.
IMPORTANT: If the ignition is ON or
turned ON when the passenger air bag
indicator lamp is disconnected,
supplemental restraint system (SRS)
related DTCs may set and be
permanently stored in the air bag
diagnosis sensor unit.
Shift selector
assembly
Casing cap
Key interlock
cable adjuster
Figure 2
2. Unlock key interlock cable adjuster
(Figure 3 and Figure 4):
a. Press the pawls (B) of the key
interlock cable slider (A),
b. while sliding it in the direction of the
casing cap (C),
c. and then separate the adjust holder
(D) and slider.
Figure 3
3. Adjust key interlock cable (Figure 4):
a. Shift to “P” position (if not already).
b. Turn the ignition switch to LOCK
position.
NOTE:
 Do not bend or twist the cable
forcefully.
 Confirm that the casing cap is
fastened to the cable bracket
(Figure 2).
Key interlock
cable
Adjust holder
Key interlock
rod
Figure 4
2/5
NTB17-073
c. Pull the adjust holder onto the key
interlock rod until movement stops
and adjust holder cannot be pulled
any further; all free-play has been
removed.
Adjust holder
Key interlock
rod
Figure 5
d. While holding the adjust holder in
position from step “c”, Move the key
interlock cable slider towards the key
interlock rod side and lock it (over the
adjust holder).
Adjust holder
Key interlock
rod
Key interlock
cable slider
Figure 6
4. Proceed to Inspection after Adjustments on next page.
3/5
NTB17-073
Inspection after Adjustments
5. After performing key interlock cable adjustment confirm the following items:
a) “Control Device”
i) To operate the “control lever” from “P” position to other ranges under ignition ON
state, the lever is not operable unless the brake pedal is stepped on.
ii) In other ranges, it is operable regardless of the brake pedal. At “P” position, the
“control lever” is not operable under any state other than ignition ON.
b) “Steering Lock”
i) The key can be removed only when the “control lever” is in the “P” position.
6. Turn the ignition OFF, and then disconnect the passenger air bag indicator lamp.
IMPORTANT: If the ignition is ON or turned ON when the passenger air bag
indicator lamp is disconnected, supplemental restraint system (SRS) related DTCs
may set and be permanently stored in the air bag diagnosis sensor unit.
7. Reassemble the vehicle in reverse order of disassembly.
8. After turning the ignition ON or starting the engine, make sure the supplemental air bag
lights turn OFF after approximately seven (7) seconds.
9. Use CONSULT-III plus to erase any DTCs caused by this repair.
4/5
NTB17-073
CLAIMS INFORMATION
Submit a Primary Operation (PO) type line claim using the following claims coding:
MODEL
DESCRIPTION
OP CODE
SYM
DIA
FRT
Rogue
Adjust Key Interlock Cable
JX51AA
ZE
32
0.5
5/5
NTB17-073