A461631 2042182-

Technical Service Bulletin
46 Squeal from front brakes
46 16 31 2042182/1 March 18, 2016.
Model(s)
Year
VIN Range
Vehicle-Specific Equipment
Q5
2013
047567 - 999999
2.0TFSI, 3.0TFSI, 3.0TDI
Q5
2014 - 2017
All
2.0TFSI, 3.0TFSI, 3.0TDI
Condition
Customer reports hearing a squeal noise from the front brakes in the following conditions:
When:
During first brake application in the morning, with cold brakes
Speed:
Below 20 mph
Temperature:
Below 40ºF
Conditions:
High humidity
Tip: For an example of the sound, see the video located at: https://audiexternal.kzoplatform.com/swf/player/314 (Figure 1).
Figure 1. QR code for viewing the
video with a QR code reader on
phones and tablets. Alternatively,
the video can be accessed
through computer internet
browsers at the link provided in
this bulletin.
Technical Background
Not applicable.
© 2016 Audi of America, Inc.
Page 1 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Production Solution
Not applicable.
Service
Before proceeding, check the following table to confirm that this bulletin applies.
Model
Model years
Front brakes (Brembo) disc size
Q5 2.0T (non-hybrid)
2013 to 2017: All
320 x 30 mm
Q5 3.0T (without SQ5)
2013 to 2017: All
345 x 30 mm
Q5 TDI
2014 to 2017: All
345 x 30 mm
Note:
• This TSB only applies to Q5 models listed in the table above.
• This TSB applies only to vehicles produced after 12/10/2012 (SVM code will only be accepted after production
date of 12/10/2012).
• This TSB does not apply to Q5 models built before 2013 and does not apply to hybrid or SQ5 models (due to
different front brakes).
Tip: Rust/corrosion build-up, grooves, or glazing on the braking surface of the brake disc may cause brake
noise and must be considered when replacing brake pads. Brake discs that are worn close to the wear limit or that
are at the wear limit may also contribute to brake noise.
1. Replace the front brake pads according to the instructions in Elsa at: Repair manual >> Chassis Brake System
>> 46 Mechanical Components >> Front Brakes >> Brake Pads, Removing and Installing, Brake 1LB and 1LC
or Brake Pads, Removing and Installing, Brake 1LE and 1LP.
Note:
• Some vehicles may have two shims glued to the
back of the front brake pads (Figure 2). Do not
transfer these shims to the new pads.
• New brake pads have an adhesive backing that
should be used to properly attach the pads to the
caliper.
Figure 2. Shims on back of front brake pads.
© 2016 Audi of America, Inc.
Page 2 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
The following steps must be followed to ensure proper installation of the pads:
• Thoroughly clean and dry each piston (Figure 2, arrows) to ensure
that the new pads will properly adhere to the pistons.
• Do not apply any lubricants to the pads or calipers.
• After the pads are installed in the calipers, apply full pedal pressure
for at least 10 seconds to ensure proper adhesion of the pads to the
pistons.
• In order to allow the glue to set, do not drive the vehicle for 10
minutes after new pads have been installed.
Figure 2. Location of pistons.
2. Replace the rear brake pads according to the instructions in Elsa at: Repair manual >> Chassis Brake System
>> 46 Mechanical Components >>Rear Brakes>>Removing and installing brake pads.
3. Embed the brakes:
A. Use medium pedal pressure to slow the car from approximately 35 mph to 10 mph. Repeat this process ten
times.
B. Next, drive for approximately 5 minutes at maximum allowable speeds, without braking, to allow the brakes
to cool down.
C. Repeat steps A and B if necessary.
Note:
Do not perform ABS stops as a way of embedding the brakes. Brake pads and discs may be permanently
damaged if brakes are overheated prior to being properly embedded.
4. Perform SVM update with the following code: 03A014
This update changes the ABS/ESP software due to the new brake pad compound and changes the vehicle PR
number to help in identifying and tracking vehicles with new parts.
SVM Update Instructions
1. Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating
instructions.
2. Update the vehicle using the SVM action code as listed in the table below.
© 2016 Audi of America, Inc.
Page 3 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Model
Old Software
Part Number
Old Software
Version
New Software
Part Number
New
Software
Version
SVM Code
Input
Q5 2.0T / 3.0T/ 3.0TDI
8R0907379AS
0020
8R0907379BG
0030
03A014
Q5 2.0T / 3.0T/ 3.0TDI
8R0907379AM
0030
8R0907379BG
0030
03A014
Q5 2.0T / 3.0T/ 3.0TDI
8R0907379AL
0040
8R0907379BG
0030
03A014
Warranty
Claim Type:
110
Service Number:
4636
Damage Code:
0010
Labor Operations:
4 wheels remove+reinstall
4405 2099
40 TU
Brake pads, front remove+reinstall
4636 2050
50 TU
Brake pads, rear remove+reinstall
4638 2050
50 TU
GFF and software update
0150 0000
Time stated on
diagnostic
protocol
Diagnostic Time:
(Max 60 TU)
Road test prior to service procedure
0121 0002
10 TU
Road test after service procedure
0121 0004
10 TU
Technical diagnosis at dealer’s discretion
(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:
As per TSB #2042182/1
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.
© 2016 Audi of America, Inc.
Page 4 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Required Parts and Tools
Part Number
Part Description
Quantity
8R0698151H (3.0 TFSI & TDI)
1 set of front brake pads
1
8R0698151K (2.0 TFSI)
1 set of front brake pads
1
8K0698451D (3.0 TFSI & TDI)
1 set of rear brake pads
1
8K0698451C (2.0 TFSI)
1 set of rear brake pads
1
Check ETKA for applicable part number
Contact (wear sensor)
1
Additional Information
All parts and service references provided in this TSB (2042182/1) are subject to change and/or removal. Always
check with your Parts Department and service manuals for the latest information.
© 2016 Audi of America, Inc.
Page 5 of 5
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.