A971545 2023283-

Technical Service Bulletin
97 After J519 control module is replaced, "Defective light bulb" warning light illuminates (DTC 01494 and
01498)
97 15 45 2023283/2 February 23, 2015. Supersedes Technical Service Bulletin Group 97 number 10-02 dated
April 23, 2010 for reasons listed below.
Model(s)
Year
VIN Range
Vehicle-Specific Equipment
Q7
2009 - 2011
All
Not Applicable
Condition
REVISION HISTORY
Revision
Date
Purpose
2
-
Revised Service (Replaced VAS PC instructions with ODIS instructions)
1
4/23/2010
Initial publication
The following conditions are present after the vehicle electrical system control module, J519, is replaced:
• A defective light bulb warning appears in the instrument cluster, but the side marker lights are functioning
normally.
• The following DTCs are stored in the vehicle electrical system control module, J519 (address word 09):
• DTC 01494 (Bulb for left parking light-M1) with fault symptom 011 (Open circuit)
• DTC 01494 (Bulb for right parking light-M3) with fault symptom 011 (Open circuit)
Technical Background
Due to a change in the software, an additional adaptation must be performed when the vehicle electrical system
control module is replaced.
Production Solution
Not applicable.
© 2015 Audi of America, Inc.
Page 1 of 4
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
Service
The adaptation channel value must be changed with test plan J519-Adaptation, Side marker lights (RG.97) in
ODIS.
1. Right-click Central Electrics (09-Vehicle Electrical System) (Figure 1, arrow 1).
2. Select Guided Functions from the pop-up menu (Figure 1, arrow 2).
Figure 1. Selecting Central Electrics (09-Vehicle Electrical System) (arrow 1) and selecting Guided Functions
(arrow 2).
© 2015 Audi of America, Inc.
Page 2 of 4
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
3. Select test plan J519-Adaptation, Side marker lights (RG.97) (Figure 2), then click Perform.
Figure 2. Selecting test plan J519-Adaptation, Side marker lights (RG.97).
4. Perform the test plan, and make sure the diagnosis for the side marker lights is deactivated (Figure 3).
Figure 3. Set the diagnosis for the side marker lights to deactivated.
© 2015 Audi of America, Inc.
Page 3 of 4
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.
Technical Service Bulletin
5. At the end of the test plan, a successful deactivation message appears. If this message does not appear, run
the test plan again.
6. Cycle the ignition and erase the fault code entries in the vehicle electrical system control module, J519
(address word 09).
Warranty
Claim Type:
Use applicable claim type. If vehicle is outside any warranty, this Technical Service Bulletin
is informational only.
Service Number:
9710
Damage Code:
0039
Labor Operations: GFF
0150 0000
Time stated on
diagnostic
protocol
(Max 100 TU)
Diagnostic Time:
GFF – Checking and clearing fault codes included in
existing labor operations
No allowance 0 TU
Road test prior to service procedure
No allowance 0 TU
Road test after service procedure
No allowance 0 TU
Technical diagnosis at dealer’s discretion
(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:
As per TSB #2023283/2
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.
Additional Information
All parts and service references provided in this TSB (2023283) are subject to change and/or removal. Always
check with your Parts Department and service manuals for the latest information.
© 2015 Audi of America, Inc.
Page 4 of 4
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior
expressed written permission of the publisher.