V961407 2038432

Technical Bulletin
Model(s)
Year
Eng. Code
Trans. Code
VIN Range From
VIN Range To
Routan
2009
All
All
All
All
Condition
96 14 07 October 6, 2014 2038432 Supersedes Technical Bulletin V961406 dated October 3, 2014 to update the
three button FOB part number.
WIN Module Replacement
Revised programing procedure for Marquardt Wireless Control Module (WCM) replacement kits.
Note:
Read this information in its entirety before beginning programming. Failure to do so may result in programming
failure.
Technical Background
The Wireless Ignition Node (WIN) module for MY 2009 Routan been superseded to the supplier Marquardt.
These kits come with the Fobiks already programmed to the WIN module. Because of this change there is a
revision in the programing of the WIN module.
Page 1 of 9
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
Note:
wiTECH™ SOFTWARE LEVEL MUST BE AT RELEASE 13.04.15 OR HIGHER FOR THIS BULLETIN.
Part No:
Part Description
System Features
7B0998021T
Marquardt WIN Kit (GX1+4K4+4E9)
All Features
Marquardt WIN Kit (GX1+4F2+4E9)
Power Sliding Door + Power lift
Gate + Central Locking
Marquardt WIN Kit (GX1+4F2+4E0)
Power Sliding Door + Central
Locking
Marquardt WIN Kit (GX0+4F2+4E0)
Central Locking Only
Marquardt WIN Kit (GX1+4K4+4E0)
Power Sliding Door + Central
Locking W/Remote Start
(7 button FOB)
7B0998021S
(6 button FOB)
7B0998021R
(5 button FOB)
7B0998021Q
(3 button FOB)
7B0998021AA
(6 button FOB)
Note:
Be sure to match the PR code using a VIN in ETKA to obtain the proper kit configuration. Always check the current
vehicle key FOB button configuration to see if the remote start feature has been added to the vehicle. Panic button
is included in the all the configurations.
Production Solution
Not applicable.
Page 2 of 9
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
Service
Using a Scan Tool (wiTECH) with ElsaPro and the appropriate Diagnostic Procedures, verify all engine systems
are functioning as designed. If DTC's are present record them on the repair order and repair as necessary before
proceeding further with this bulletin.
NOTE:
This procedure requires the wiTECH Desktop Client to perform this procedure. The wiTECH software must be
v13.04.15 to program MY2009 Routan WIN. Refer to Service Information VSE-14-18 located on Service Net>
under Workshop-Equipment> wiTECH/ StarMobile-Diagnostic-Tool> Service-Information
Install a Volkswagen approved battery charger/maintainer to ensure battery voltage does not drop below 13.2
volts. Do not allow the charging voltage to climb above 13.5 volts during the programming process.
FOR THIS PROCEDURE, the Secret Key data in the new WIN module is the one that should be retained on the
vehicle.
Installing new WIN module with preprogrammed FOBIKs
The WIN module and FOBIKs in this package have been preprogrammed together as a set. Because they are
programmed these FOBIKs cannot be used with another WIN module or on another vehicle. The original FOBIKs
for this vehicle cannot be used with this new WIN module and will no longer be usable.
NOTE:
Because these parts are preprogrammed, the standard WiTECH WIN Replacement procedure must be altered. It
is critical that during the installation of the new WIN module that the back-up copy of the Secret Key, stored in the
PCM is not transferred to the new WIN module overwriting the programming which matches the supplied FOBIKs.
For this reason these instructions must be followed explicitly! Failure to follow these instructions could render the
new FOBIKs obsolete.
Page 3 of 9
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
Repair Procedure
Remove the original WIN module and install the new WIN module per the Elsa Repair Manual.
Insert a new provided FOBIK into the WIN module and switch the ignition to the run position.
Connect the WiTECH Desktop Client to the vehicle.
1. Select the WCM (Wireless Control Module) from the Vehicle View screen (Figure 1).
Figure 1
2. Select the Misc. Function tab and select WIN Replaced procedure (Figure 2).
Figure 2
Page 4 of 9
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
3. When prompted select continue (Figure 3).
Figure 3
4. When prompted, enter the PIN into the new WIN. This step will write the PIN to the new WIN. You will
be asking to verify the PIN is correct before this procedure can continue. If PIN is correct select Continue
to proceed (Figure 4).
Figure 4
5. Run the procedure up to the confirmation screen that states “PIN has been programmed”.
NOTE:
DO NOT SELECT CONTINUE! You must Close the procedure at this point. (Figure 5)
Figure 5
Page 5 of 9
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
NOTE:
Cycling the ignition key too quickly may interrupt the learn process.
Cycle the ignition key OFF and remove the key for 2 seconds.
Reinsert the ignition key and switch the key to the ACC/ON position.
Using either supplied FOBIK verify the vehicle can be started.
Tip:
If the vehicle starts, the procedure has been successfully.
NOTE:
If the vehicle does not start, something has failed in the procedure. DO NOT CONTINUE. Contact Volkswagen
Technical Assistance for assistance.
• If the vehicle started, verify the second FOBIK also starts the vehicle.
• Remove the FOBIK and verify the RKE functions correctly.
• Perform the following steps to complete this procedure.
Procedure Completion:
This procedure will transfer the new Secret Key in the WIN module to the PCM.
6. Select the Misc. Function tab and select PCM Replaced procedure (Figure 6).
Figure 6
Page 6 of 9
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
7. This screen shows a WARNING that running the “PCM Replaced” procedure may cause a loss of valid
secret key information in the PCM. To finish installing the preprogrammed WIN the secret key information
in the PCM must be changed, so selecting “Continue” is the correct response (Figure 7).
Figure 7
8. When prompted, enter the PIN. Like the previous step you will be asked to verify the PIN is correct
before the routine can proceed. Select Continue (Figure 8).
Figure 8
9. When you receive a confirmation that the PIN entered is correct, select Continue (Figure 9).
Figure 9
Page 7 of 9
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
10. When prompted to update the current WIN VIN, select Continue. The PCM already has the correct
VIN, but this step is required to proceed to the following steps (Figure 10).
Figure 10
11. When you will receive a confirmation that the VIN write was successful select Continue (Figure11).
Figure 11
12. The final step is the transfer of the (new) secret key from the WIN to the PCM. This will replace the old
secret key with the new secret from the new WIN. When you receive a confirmation that the transfer of
secret key was successful, select Close (Figure 12).
Figure 12
• Cycle the ignition key.
• Verify one more time all FOBIKs and both ignition keys start vehicle.
• Clear any DTCs that were set during the programming of the WIN.
Page 8 of 9
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
Warranty
Information only.
Required Parts and Tools
No special parts required.
Tool Description
Tool No:
Midtronics Battery Tester/Charger
InCharge 940 (INC-940) or
GRX 3000 VAS
StarMOBILE Tester Kit or
CH9401 (SW level 10.01.23 or higher)
VW MICRO POD Tester Kit
VWMICROPOD
wiTECH Desktop Client
(Software level 13.04.15 or higher)
Additional Information
All part and service references provided in this Technical Bulletin are subject to change and/or removal.
Always check with your Parts Dept. and Repair Manuals for the latest information.
Page 9 of 9
© 2014 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.