SP 284-051

Service Program
Trucks
Volvo Trucks North
America
Greensboro, NC USA
Date
2.2014
Group
No.
284 051
Release
Page
01
1(8)
Engine Control Module (ECM) Software
Update
D11J, D13J, D16J
VAH, VHD, VN
SP 284-051, Engine Control Module (ECM) Software
Update
(February 2014)
Information
Software updates with enhancements are available for the engine control module (ECM) for
VOLVO D11J, D13J and D16J engines with US2014 emission level on vehicles built before
February 7, 2014. Software updates address the following.
•
•
•
•
Regenerations in cold climates (below -20°C [-4°F])
Improved soot level reporting during parked regeneration
Cold start time delay algorithm
Piston cooling jet (PCJ) diagnostic fault logic
Tools
Premium Tech Tool version 2.02.80 or higher
Diagnostic Connector 88890304
Communication Interface 88890300 with firmware 1.12.0.2 or higher
Note: Check Premium Tech Tool version by clicking on Help tab and then click on “About
Tech Tool”.
USA63847
PV729-SP284-051
English
Volvo Trucks North America
Service Program
Date
2.2014
Group
No.
Release
284
051
01
Procedure
DANGER
Do not attempt to repair or service this vehicle without having sufficient training, the correct
service literature and the proper tools. Failure to follow this could make the vehicle unsafe
and lead to serious personal injury or death.
1 Verify service program eligibility by checking service program status in eWarranty.
2 Secure the vehicle for service by parking it on a flat level surface, applying the parking
brake, chocking the rear wheels, and placing the transmission in neutral.
3 Connect Premium Tech Tool (PTT) to the vehicle diagnostics connector using the 16 pin
OBD cable 88890304 and Communication Interface 88890300. Connect the PC to a
functional LAN or modem connection and a 120 Volt AC source.
4 Turn the ignition switch “ON”.
5 Log in to PTT and Identify Vehicle is displayed.
Page
2(8)
Volvo Trucks North America
Service Program
Date
2.2014
Group
No.
Release
284
051
01
6 Once the vehicle has been identified, enter the Work Order Number information, then click
Start Work.
W2079940
Page
3(8)
Volvo Trucks North America
Service Program
Date
2.2014
Group
No.
Release
284
051
01
7 From the Main Menu select Program and then Program Control Unit 1700-08-03-39. Then
click Start.
W2085457
Page
4(8)
Volvo Trucks North America
Service Program
Date
2.2014
Group
No.
Release
284
051
01
8 Select a Control Unit from the list. For this campaign, update the engine control module
(EMS).
W2079943
Page
5(8)
Volvo Trucks North America
Service Program
Date
2.2014
Group
No.
Release
284
051
01
9 Select Program to update the control unit with the latest software.
W2085461
10 Certain conditions must be met to continue with programming: battery voltage above 10v,
parking brake applied, and ignition key in ON position with engine not running. When all
conditions have been met, click Continue to proceed with programming.
W2080113
Page
6(8)
Volvo Trucks North America
Service Program
Date
2.2014
Group
No.
Release
284
051
01
11 Select “I accept” to agree to the terms and press Continue to proceed.
Note: For North America, the programing is NOT chargeable. An invoice will not be
generated.
W2085462
12 When EMS programming is complete, click Exit to return to the main menu.
13 Clear any diagnostic trouble codes (DTC) and Finish Work.
Page
7(8)
Volvo Trucks North America
Service Program
Date
2.2014
Group
No.
Release
284
051
01
Reimbursement
This repair is covered by an authorized Service Program. Reimbursement is
obtained via the normal claim handling process.
Claim Type (used only when uploading from the Dealer Bus. Sys.)
B
Recall Status
Vehicle inspected, repair not required
1- Inspected
OK
Vehicle repaired per instruction
2- Modified
per
instruction
Labor Code
Primary Labor Code
28444-0-01
— 0.4 hrs
Time to take charge and determine campaign status
17003–0–0
— 0.3 hrs
Causal Part
3092091
Authorization Number
SP284–051
Expiration Date
31-AUG2014
Note: Take Charge Time is not included in the Labor Code for this operation. Take charge
may be eligible but can only be used once per repair visit. If vehicle is having other warranty
repairs performed, take charge should be charged to the warranty repair, otherwise take
charge can be charged to this service program.
Page
8(8)