12TL8
Service Bulletin Details
Public Details for: 12TL8
12tl8 w470589149100 - filter cap with test port
- 2018 - 2017 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 - 2010 - 2009 - 2008 - 2007 - 2006 - 2005 -
Models from 2018
2018 FCCC S2C 106CAB |
2018 FCCC S2G |
2018 FCCC XBR |
2018 FCCC XCL |
2018 FCCC XCM |
2018 FCCC XCR |
Models from 2016
2016 FCCC S2 |
2016 FCCC S2G |
2016 FCCC XBP |
2016 FCCC XBR |
2016 FCCC XBS |
2016 FCCC XCL |
2016 FCCC XCM |
2016 FCCC XCP |
2016 FCCC XCR |
2016 FCCC XCS |
Models from 2015
Models from 2014
Models from 2013
2013 FCCC S2 106 CH |
2013 FCCC S2C 106CAB |
2013 FCCC XBP |
2013 FCCC XBR |
2013 FCCC XBS |
2013 FCCC XCL |
2013 FCCC XCM |
2013 FCCC XCP |
2013 FCCC XCR |
2013 FCCC XCS |
Models from 2012
Models from 2011
Models from 2010
2010 FCCC MCL |
2010 FCCC XBP |
2010 FCCC XCM |
2010 FCCC XCP |
Models from 2009
2009 FCCC MCL |
2009 FCCC XBP |
2009 FCCC XCM |
2009 FCCC XCP |
Models from 2008
2008 FCCC MCL |
2008 FCCC XBP |
2008 FCCC XCM |
2008 FCCC XCP |
Models from 2007
2007 FCCC MCL |
2007 FCCC XBP |
2007 FCCC XCM |
2007 FCCC XCP |
Models from 2006
2006 FCCC MCL |
Models from 2005
2005 FCCC MCL |
No.: 12 TL-8 December 5, 2012 TO: Service Locations FROM: Service Operations SUBJECT: W470589149100 - Filter Cap with Test Port GENERAL INFORMATION The Detroit Diesel special tool group has released a new essential tool for the fuel system on DD13, DD15, and DD16 engines equipped with a two-filter fuel system. For service locations that are EPA07 and EPA2010 DD certified in SSI, no action is required. Tools will be automatically shipped and invoiced to your facility during the month of November. Locations that are NOT EPA07 and EPA2010 DD certified in SSI, will need to order the tools through the Paragon system. The W470589149100 filter cap with test port, used in conjunction with the existing J-48706 gauge set, allows measuring of the low pressure pump inlet pressure. TOOL USAGE INSTRUCTIONS 1. Using a 36 mm socket, unscrew the pre-filter cap. 2. Pull the cap and pre-filter straight up and out of the fuel filter housing. 3. Remove the pre-filter (1) from the pre-filter cap (2) by placing the filter on a solid surface and applying pressure on the pre-filter cap (2) at an angle. 12 TL-8 2 4. Snap the pre-filter into the W470589149100 filter cap with test port. 12/5/2012 12 TL-8 3 12/5/2012 5. Apply a thin coat of petroleum-based lithium grease to the pre-filter seals (1) and the W470589149100 filter cap seal ring (2). 6. Install the pre-filter into the fuel filter module. 7. Turn the W470589149100 filter cap with test port counterclockwise until a clicking sound is heard, then turn clockwise and hand tighten. NOTE: A 36 mm deep well socket is required to tighten the W470589149100 filter cap with test port. 8. Torque the W470589149100 filter cap with test port to 55-60 N·m (41-44 lb·ft). 9. Using the ESOC 350 priming unit, prime the fuel system. 10. Connect the J-48706 gauge set to the W470589149100 filter cap with test port. 11. Follow published diagnostics in Power Service Literature (PSL). 12 TL-8 4 12/5/2012 ADDITIONAL INFORMATION Ordering Information - Tools will be automatically shipped and invoiced to your facility during the month of November. Locations that are NOT EPA07 and EPA10 DD certified in SSI, will need to order the tools through the Paragon system. Tools can be ordered through Paragon using a DDE supplier prefix. DDE W470589149100 Filter Cap w/Test Port CONTACT INFORMATION Please contact the Detroit™ Customer Support Center at 800-445-1980 or email [email protected] if you have any questions.