Tacoma CRC_Techn

XXXXXXXXXXXXXXXXXXX IMPORTANT UPDATE XXXXXXXXXXXXXXXXX
COLD CLIMATE STATES ONLY
CT, DE, IL, IN, KY, MA, MD, ME, MI, MN, NH, NJ, NY, OH, PA, RI, VA, VT, WI & WV and District of
Columbia
TECHNICAL INSTRUCTIONS
FOR
CORROSION-RESISTANT COMPOUND CAMPAIGN H0F
CERTAIN 2005 THROUGH 2010 MODEL YEAR TACOMA
CORROSION-RESISTANT COMPOUND APPLICATION
COLD CLIMATE STATES ONLY
CT, DE, IL, IN, KY, MA, MD, ME, MI, MN, NH, NJ, NY, OH, PA, RI, VA, VT, WI & WV
UPDATED 12.8.17
12.8.17 Update:
• Update to Technician Certification Requirements
The repair quality of covered vehicles is extremely important to Toyota. All dealership technicians performing
this repair are required to successfully complete the most current version of the E-Learning course “Safety
Recall and Service Campaign Essentials”. The Technician must also be fitted for a NIOSH approved respirator.
To ensure that all vehicles have the repair performed correctly, technicians performing this repair are required to
currently hold at least one of the following certification levels:
• Maintenance Certified Technician and above
Always check which technicians can perform the recall remedy by logging on to
https://www.uotdealerreports.com. It is the dealership’s responsibility to select technicians with the above
certification level or greater to perform this repair. Carefully review your resources, the technician skill level, and
ability before assigning technicians to this repair. It is important to consider technician days off and vacation
schedules to ensure there are properly trained technicians available to perform this repair at all times.
•
•
I.
For a complete list of Site Selection Guidelines and, Fire, Building, and Zoning Codes
information for your state, please refer to the Dealer Information Packet. Please ensure
your dealership complies with all regulations set forth in this packet.
Keep records to comply with Federal/State/Local regulations and requirements. See the
Federal, State & Local Requirements Guide and any Supplements to that Guide.
OPERATION FLOW CHART
Verify Vehicle Eligibility:
1. Check the VIN range
2. Check the TIS vehicle Inquiry system
Yes
Is the vehicle registered in one of the Cold Climate States?
No
No further action required.
No
Contact your regional
representative for assistance.
Yes
Did the vehicle pass the ZH6 frame inspection?
No
Yes
Remove the rust and clean the frame.
Was perforation 10mm or larger found in the locations identified in
green below (during the rust removal and/or cleaning process)?
Yes
No
Apply the 712AM Internal CRC to the areas of the frame outlined in the
TI.
Proceed with Frame
Replacement as outlined in the
ZH6 TI.
Install the Body Plugs after applying the 712AM
and before applying the Noxudol 300S.
Apply Noxudol 300S (External Application) to the top, bottom and
sides of the frame as outlined in the TI.
After applying the CRCs place a CRC Customer Information
Hang Tag on the rear-view mirror.
After 24 hours, return the vehicle to the customer.
Campaign Completed.
Note: Ensure to follow the entire procedure and perform all steps completely (e.g. cleaning/rust
removal, CRC application, one kit per vehicle, etc.) any deviation will be subject to warranty claim
debit.
2
II.
IDENTIFICATION OF COVERED VEHICLES
A.
COVERED VIN RANGE
Notes:
• Vehicles currently registered in the Cold Climate States* or the District of Columbia (D.C.) that do not
have significant corrosion found are eligible for Corrosion-Resistant Compound (CRC) application to
the frame if it did NOT previously have the frame sprayed and/or had the frame previously replaced.
• Check TIS to confirm the VIN is covered in H0F. This will verify the vehicle is covered and has not
already been completed prior to dealer shipment or by another dealer.
• TMS warranty will not reimburse dealers for repairs conducted on vehicles that are not covered or
were completed by another dealer.
* CT, DE, IL, IN, KY, MA, MD, ME, MI, MN, NH, NJ, NY, OH, PA, RI, VA, VT, WI, & WV
III. PREPARATION
A.
PARTS
Please be aware that only dealers in Cold Climate States will be allowed to order the following CRC kit.
The necessary CRC kits can be ordered through the chemical program provided by Dealer Tire
(Complete Maintenance Care). The CRC kits will be shipped directly from AMREP. Your dealership
should not order kits until you have confirmed an appointment. However, please keep in mind it will take
at least 5 business days for CRC kit delivery. Deliveries are only scheduled on business days.
Saturday deliveries are not available.
Model
Tacoma
Part No.
00289-T00KT-DS
Part Description
T00-Corros Res Kit (CRC Kit)
Qty/Unit
1
The kit above includes the following parts:
Noxudol 300S – 3 Liters
Parker 712AM – 1 Liter
1. When Ordering CRC Kits Please Note:
• Each kit will contain the exact amount of CRC for one vehicle.
• The CRC kits listed will be drop-shipped from AMREP, not your local PDC. Do not order
more than your immediate needs, as these materials are not returnable or refundable.
• Orders for these parts should be placed separately from orders of other drop ship
chemicals.
• Refer to the Appendix for the Safety Data Sheet (SDS).
2. When Storing the CRC Kits Please Note:
• Follow local, state and federal regulations for hazardous materials storage and disposal
that are explained in the Hazardous Waste Management Section of the Federal, State and
Local Requirements Guide of the Dealer Information Packet.
• Store the CRC kits at room temperature (refer to the SDS for detailed instructions).
3
B.
SUPPORT MATERIALS
•
The following support materials can be ordered through the dealer’s facing PDC:
Part Number
Part Name
Qty/Veh
5114A-04010
5114B-04010
90178-A0024
90119-A0170
Seal, Frame Side Rail, RH
Seal, Frame Side Rail, LH
Nut, Flange
Bolt, W/Washer
1
1
2
2
94151-80801
94183-00831
94611-10800
90105-08500
Nut, Flange
Nut, Lock
Washer, Plate
Bolt, Flange
2
2
4
2
04007-18335
Plug Hole Kit CRC Application
The kit listed above includes the following parts:
Part Number
90950-01A24
90950-01984
90950-01987
90950-01631
90950-01983
90950-01989
90950-01990
90950-01992
90950-01991
90950-01A09
90950-01931
90950-01A11
90389-05012
04007-23104
Part Description
PLUG,HOLE
PLUG,HOLE
PLUG,HOLE
PLUG,HOLE
PLUG,HOLE
PLUG,HOLE
PLUG,HOLE
PLUG,HOLE
PLUG,HOLE
PLUG,HOLE
PLUG,HOLE
PLUG,HOLE
PLUG,HOLE
1
Qty
2
2
8
4
4
4
4
2
4
2
1
2
2
Plug Hole Kit CRC Application
1
The kit listed above includes the following parts:
Part Number
90950-A1008
90950-A1009
90080-46327
90119-A0169
•
*
C.
Part Description
PLUG,HOLE
PLUG,HOLE
CLIP
BOLT w/WASHER
Qty
2
2
2
4
The following support materials can be ordered through the MDC:
Part Number
Part Description
00411-11004
Corrosion-Resistant Compound Customer Information Hang Tag*
Qty
1 per vehicle
Additional CRC Customer Information Hang Tags can be ordered in packages of 25 through the MDC.
STANDARD TOOLS & EQUIPMENT
• Standard hand tools
• Flat chisel
• Scraper
• Wire brush
• Air nozzle
• Infrared thermometer
• Air coupler (quantity 2)
4
SPECIAL EQUIPMENT
The following equipment was shipped to your dealership prior to the launch of LSC H0F.
Note: Due to federal, state and local regulations, each dealer is only allowed to have one set of
spray guns. Any old previous spray guns from previous campaigns should be disposed of in
accordance with local regulations.
As a result, each participating dealer will have 2 total spray guns in their possession:
Equipment
Purpose
Application Area
Spray Gun
Noxudol 300S
Exterior Frame CRC Application
Spray Gun
712AM
Interior Frame CRC Application
90o Drill Adapter
Drill Holes
These tools will be used to attach
the frame side rail seal.
Drill Bits
Drill Holes
The items below were previously shipped to your dealership for previous CRC campaigns.
Magnet Kit
• 30 Rare Earth Magnets – See section VI.C.1 “Attach Plastic Sheet” for details.
*Follow the CRC Support link located in the left bottom corner of the C.L.E.A.N DEALER webpage.
D.
MATERIALS & SUPPLIES (Locally Procured by Dealer)
• Protective eyewear
• Dust mask
• Appropriate NIOSH approved respirator** (Follow all Federal, State, Local
Environmental, Health and Safety Requirements such as OSHA Regulations. Please
refer to the SDS for details on the appropriate mask for each CRC.)
Example of a NIOSH**Notes:
approved respirator
• Refer to the SDS located in the Appendix for additional information on respirator use.
• It is up to the individual dealership to ensure compliance with OSHA regulations.
• If you require further assistance in regards to NIOSH approved respirators, we have found
3M® to be a useful reference/source.
3M® Technical Assistance:
1-800-243-4630
3M® Customer Service:
1-800-328-1667
3M® Web Site:
www.3m.com/occsafety
• Protective gloves
• Chemical Resistant Gloves (refer to SDS for specific type)
• Masking tape
• Duct tape
• Fire-retardant poly sheeting (tarp) or covering (if you cannot purchase the tarp from a local supplier,
please refer to CRC Tips and Examples located on the C.L.E.A.N. DEALER website
(http://cleandealer.com) for a list of possible suppliers)
• Plastic (Saran Wrap) sheet (for spray gun storage)
• Partitions (The type, size, and number of partitions used will depend on each dealer’s facility.)
• Shop cloth/paper towels
• Funnel (quantity = 2)
• Plastic sheet to contain the dripping 712AM during frame application, 3m x 3m (118in x 118in)
• Garbage Bags
IV. BACKGROUND AND COMPONENTS
Toyota has received a number of reports regarding Frame Corrosion on
2005 – 2010 model year Tacoma vehicles, 2007-2008 Tundra vehicles,
and 2005-2008 Sequoia vehicles. In these reports, customers have
indicated that vehicles operated in specific cold climate areas with high
road salt usage may exhibit more-than-normal corrosion to the vehicle’s
frame. This condition is unrelated to and separate from normal surface
rust which is commonly found on metallic surfaces after some years of
usage and/or exposure to the environment.
5
• Because of variations in State and local laws, dealerships conducting H0F in certain states may
require government approvals prior to starting the campaign. Depending upon the state,
dealerships also may be subject to restrictions on the number of vehicles to which the CRC can
be applied in any single day, week, or month. Please refer to the Dealer Information Packet and
any Supplements for important information about any such approvals or restrictions that may
apply to your dealership. Your dealership must adhere strictly to these requirements.
• For a complete list of Site Selection Guidelines, Fire, Building, and Zoning Codes information for
your state, please refer to the Dealer Information Packet as well as any Supplements. Please
ensure your dealership complies with all regulations and all issued packets/instructions.
V.
VEHICLE INSPECTION WORK PROCEDURE
Note: Vehicle frame inspection is performed under WEP ZH6, for inspection instructions go to WEP ZH6
Technical Instructions.
VI. FRAME APPLICATION WORK PROCEDURE
Allow sufficient time for the vehicle and exhaust to cool down before beginning the
application process. By following the FRAME APPLICATION WORK PROCEDURE in
these Technical Instructions, the vehicle will have additional time to cool before the
CRC’s are applied. Please refer to the SDS (In the Appendix) for flash point temp.
A.
VEHICLE PREPARATION AND REMOVAL OF FRAME RUST
1. PREPARE THE VEHICLE
a) It may be necessary to pressure wash the vehicle’s frame,
depending on its cleanliness.
Note: Time has been allotted to pressure wash the frame in the
flat rate time.
b) Place the vehicle on the lift.
Strap the vehicle to the lift with safety straps. Once
the vehicle is raised to the desired height, install
screw jacks to the front and back of the vehicle.
c) Raise up the vehicle and remove the wheels.
d) Remove the engine under cover.
e) Cover any identifying label (i.e., VIN label, etc.) on the frame
with tape.
f) Cover all exposed electrical connectors with tape to protect from
over spray.
2. REMOVE RUST FROM THE FRAME AND CROSS-MEMBERS.
a) Using a scraper or chisel remove all loose rust and rust scales
from the frame and cross-members.
Note: The use of power tools is permissible during the cleaning
process. Toyota found air scalers to work well.
Power Tools are Permissible
b) If rust perforation of 10mm or larger and/or component corrosion
damage is found during the rust removal process proceed with
frame replacement as outlined in the separate ZH6 TI.
Notes:
• Make sure to wear protective eyewear, gloves, and a dust
mask when removing rust and cleaning frame.
• Be careful not to damage the wire harness or brake lines
when removing rust.
• Be extremely cautious not to injure your hands.
• DO NOT scratch or remove the identifying labels
6
3. CLEAN THE FRAME
a) Use a wire brush and remove any remaining rust or dirt from the
frame.
Ensure to follow the procedure and perform all steps completely
(e.g. inspection, cleaning/rust removal, CRC application, one kit per
vehicle, etc.) any deviation will be subject to warranty claim debit.
b) Use an air nozzle and remove any loose rust.
Notes:
• Make sure to wear protective eyewear, gloves, and a dust
mask when performing this step.
• A slightly wet frame surface (no water droplets) is
acceptable when applying the frame CRC.
Sample of Sufficient Frame Cleaning
Before
After
B.
VEHICLE PROTECTION
1. ATTACH MASKING MATERIALS
a) Using an infrared thermometer ensure the exhaust has cooled.
b) Cover the driveshaft(s) and exhaust, with fire-retardant poly
sheeting (tarp) and secure with masking tape.
c) Cover the front and rear brake/hub assemblies with garbage
bags and secure with masking tape.
Notes:
• If necessary, cover shock absorbers with masking sheets.
• Overspray onto the driveshaft may cause vehicle vibration.
2. COVER SPARE TIRE CONTACT SURFACES ON REAR CROSSMEMBER
a) Cover the underside of the rear cross-member with duct tape
where the spare tire contacts the rear cross-member.
Front
Notes:
• Tape size/location may very if the customer has changed
spare tire size, adjust as necessary.
• Tape will not be centered on cross-member because spare
tire carrier is off center.
• Tape will prevent Noxudol 300S from sticking to the tire.
7
C.
PREPARE FOR APPLICATION OF CORROSION-RESISTANT COMPOUND (CRC)
Note: Always utilize the correct CRC kit for Tacoma CRC
Application, Part Number 00289-T00KT-DS.
Plastic Sheet Size
• 3m x 3m(118inx118in)
• Thickness = 2 mil
Attach to Floor Pan
1. ATTACH PLASTIC SHEET
a) Before spraying 712AM to the internal frame, fit the plastic sheet
on the frame utilizing the previously supplied magnet kit.
Magnet
2. SET UP THE SPRAY GUN FOR 712AM INTERNAL CRC
APPLICATION
Notes:
• Use a dedicated spray gun for the 712AM internal CRC.
• Make sure to wear protective eyewear, impervious gloves
(Viton, PVOH, etc.) appropriate Niosh approved respirator,
and refer to the SDS located in the Appendix when handling
and spraying CRC.
a) Check the temperature of the 712AM.
If the 712AM is below 72º F, place the 712AM container in
a bucket of hot water (<104º F) for 15 minutes and allow it
to warm so the proper viscosity is achieved.
b) Shake the 712AM container well so that the contents are mixed
thoroughly. Settling may occur as it sits over time.
c) Fill the dedicated tank with 712AM and attach it to the spray
gun.
d) Connect the 8mm spray tube, as shown in the illustration.
e) Adjust the spray gun nozzle flow/volume.
1. Turn the adjustment screw to the fully closed position
(clockwise).
2. Then loosen the adjustment screw 4 complete turns.
The air regulator is extremely sensitive; always follow
instruction to avoid damage to the gun!
f)
Adjust the air pressure regulator.
1.
2.
3.
4.
Place the nozzle in a clean empty box or pail.
Adjust the air regulator completely closed (No Air Flow)
Attach the air hose to gun.
Fully press the spray gun trigger, and slowly adjust the
air pressure to 72.5 psi.
Note: The air regulator has a slight delay and may take up to
10 seconds before the air pressure stabilizes. Move the
adjustment knob in very small increments (1/8 turn).
5. Recycle the amount sprayed out and use it during the
application process.
8
D.
712AM INTERNAL FRAME CRC APPLICATION
1. 712AM INTERNAL FRAME APPLICATION
a) Insert the spray nozzle into the selected holes located
throughout the frame. Reference the next page for the location,
depth, and application rate.
Note: DO NOT bend (i.e., kink) the spray nozzle.
b) Once the location, depth, and application rate is confirmed,
begin applying CRC to the internal frame.
c) When inserting the nozzle, insert so the nozzle touches the
opposite side of the frame as illustrated on the left. See Diagram
1 & 2 for applying CRC.
Note: Make sure the quick coupler on the spray tube does not
come into contact with the frame when applying the 712AM.
Contacting the frame with the quick coupler may lead to a hose
disconnection.
d) After the 712 AM has been applied, wipe away any wax on the
frame’s exterior with cloths or paper towels.
Notes:
• Follow all SDS guidelines for the 712AM which can be
found in the Appendix.
• Follow the given application speeds when applying the
712AM to the inner surface of the frame.
• The exact insertion point locations may vary depending on
the cab configuration.
9
Diagram 1: Internal CRC Application
712AM Internal CRC Application
Tube Insert Locations, Depth, and Application Speed
Step 1 & 2
CRC Temperature
Application Speed
22°C (72°F)
0.2 m/sec (8 in/sec)
30°C (86°F)
0.3 m/sec (12 in/sec)
Note: m/sec = meters/second
Front
Step 3
STEP ①
90cm
(35 in)
Note: Steps 1 to 3 show application procedure only for the right
side of the vehicle. Perform application for the left side of the
vehicle in a similar manner.
Step 1 (refer to the table above for application rate):
a) While applying the 712AM, insert the nozzle 90cm (35 in) into the
side-rail.
b) Continue applying the 712AM while removing the nozzle.
Repeat Step 1 for a total of 2 laps
STEP ②
5 cm
(2 in)
Step 2 (refer to the table above for application rate):
a) Insert the nozzle 5 cm (2 in.) towards the front of the frame.
b) Move the nozzle in a circular motion while applying the 712AM.
Note: Make sure to only insert the nozzle 5cm (2 in) to avoid over
spraying onto the engine.
STEP ③
90cm
(35 in)
Step 3 (refer to the table above for application rate):
a) While applying the 712AM, insert the nozzle 90cm (35 in) into the
side-rail. (contact the top center of the frame while inserting
nozzle).
b) Continue applying the 712AM while removing the nozzle.
Repeat Step 3 for a total of 3 laps
THE ENTIRE LITER OF 712AM MUST BE APPLIED TO THE FRAME OF THE VEHICLE!
Notes:
• Follow all SDS guidelines for the 712AM which can be found in the Appendix.
• Only one side is given. Tube insert locations are the same for both sides.
• Follow the given application speeds when applying the 712AM to the inner surface of the frame.
The exact insertion point locations may vary depending on the cab configuration.
10
2. REMOVE THE PLASTIC SHEET
a) Let the 712AM complete dripping.
b) With a cloth wipe off any drips of 712AM dripping from the fame.
c) Before installing the body plugs, confirm that the excess 712AM has stopped dripping from the frame.
E.
INSTALLATION OF BODY PLUGS AND FRAME SEAL
1. INSTALL FRAME RAIL SEAL
Note: Due to the interference of key vehicle
components, the frame seal will need to be
modified to be installed onto the outer frame rail.
Template A and B Sample Pic
a) Using Template A & B in the appendix, locate the
location on both outer frame side rails.
• Print Template on 8.5” x 11” paper
• Cut the template out
• Align the template with the datum hole
• Mark location of hole on outer frame side rail
b) Use a center pin punch to create a dimple for the drill
bit so it will not wander during drilling.
c) Using the 90o drill adapter provided and the stepper bit,
drill a 9mm (3/8”) hole in the outer frame side rail as
shown.
d) Repeat procedure for opposite side frame rail.
e) Using Template C and D, modify both the left and right
side frame seal by drilling a (3/8”) hole in the location
shown.
Drill 9mm Hole
Template C & D Sample
f)
Install the bolt through the frame and torque the flange
nut.
Torque Spec: 18.5 N∙m (13.5 ft∙lbf)
g) Install the washer onto the bolt.
h) Install the frame seal second washer and locking nut
onto the frame and torque to spec.
Torque Spec: 6 N∙m (52 in∙lbf)
Part #
90105-08500
94611-10800
94151-80801
94183-00831
Part Name
Bolt, Flange
Washer
Nut w/Flange
Lock Nut
Qty
2
4
2
2
11
1. INSTALL THE BODY PLUGS
・Body plug locations are symmetrical unless noted. The instructions only show one side, ensure
you install in both locations.
・Install the plugs for prevention of dripping and water entry.
Plug 9
Plug 7
Plug 8
1GR LH Side
2TR RH side
Plug 6
Plug 2
2wd Only
Plug 1
Plug 8
90950-01631
Plug 0
4x4, PreRunner Only
Plug 11
2wd Only
Plug 4
PLUG DIAGRAM/ID
P/N
90950-01992
INSTALLATION INSTRUCTIONS
Push to seat installation
TOTAL QTY
2
Note: This is a one time install plug, it will break if you try to
remove.
90950-01983
90950-01990
1
90950-01984
4
Push to seat install.
There are two callout locations for this plug.
Push to seat installation.
90950-01989
90950-01931
4
2
4
Engine variation determines which rail to install plug on.
1
Push to seat installation
90950-01991
Note: This is a one time install plug, it will break if you try to
remove.
4
90950-01987
Dashed line indicates part vary by vehicle type or
configuration.
8 FOR 4WD
6 FOR 2WD
90950-01A09
2wd Only Order separately
1
90950-01A11
2WD ONLY
2
90950-01631
Push to seat installation.
4
12
PLUG INSTALL CONTINUED
90389-05012
90950-A1009
90950-46327
90950-A1008
90119-A0169
PLUG DIAGRAM/ID
90950-01A24
P/N
INSTALLATION INSTRUCTIONS
90389-05012
This plug is installed by reaching through the 0
crossmember.
Reach through cab mount and install body plug.
LARGE CIRCLE
PLUG
REGTANGLE
PLUG WITH
SLOT FOR
SCREWDRIVER
90950-A1008
Bolts
90119-A0169
90950-A1009
90080-46327
90950-01A24
Using a flap tip screw driver install the plug into the
side rail through the crossmember.
Install bolts into threaded holes in the bottom of the
frame rail as shown.
Push to seat installation
TOTAL QTY
2
2
2
4
Install this plug into the bottom of the frame rail as
shown.
It must be installed with the channel opening facing
the outer portion of the frame to ensure road spray
does not enter the frame.
2
13
F.
APPLICATION OF NOXUDOL 300S EXTERNAL CRC APPLICATION
1. LOWER THE VEHICLE
2. SETTING UP THE SPRAY GUN FOR NOXUDOL 300S
EXTERNAL FRAME CRC APPLICATION
Notes:
• Use a dedicated spray gun for the NOXUDOL 300S.
• Make sure to wear protective eyewear, chemical resistant
gloves, appropriate NIOSH approved respirator, and refer
to the SDS located in the Appendix when handling and
spraying CRC.
a) Check the temperature of the Noxudol 300S.
If the Noxudol 300S is below 72º F, place the Noxudol
300S container in a bucket of hot water (<104º F) for 15
minutes and allow it to warm so the proper viscosity is
achieved.
b) Shake the Noxudol 300S container well so that the contents are
mixed thoroughly. Settling may occur over time.
c) Fill the dedicated tank with Noxudol 300S and attach it to the
spray gun.
d) Connect the external spray tube, as shown in the illustration. .
e) Adjust the spray gun nozzle flow/volume.
1. Turn the adjustment screw to the fully closed position
(clockwise).
2. Then loosen the adjustment screw 3.5 turns.
Caution: Air regulator is extremely sensitive; always
follow instruction to avoid damage to the gun!
f)
Adjust the air pressure regulator.
1. Place the nozzle in a clean empty box or pail.
2. Completely close the air regulator (No Air Flow).
3. Attach the air hose to the gun
4. Fully press the spray gun trigger, and slowly adjust the
air pressure to 50 psi.
Note: The air regulator has a slight delay and may take up to
10 seconds before the air pressure stabilizes; Move the
adjustment knob in very small increments (1/8 turn).
5. Recycle the amount sprayed out and use it during the
application process.
g) For Noxudol 300S, it will be necessary to refill the spray gun.
1. Disconnect the air hose
2. Loosen the bottle to slowly discharge the pressure through
the threads of the bottle.
3. After all the pressure is discharged, detach the bottle.
Notes:
• DO NOT remove the bottle until the pressure is released.
• DO NOT pull the spray gun trigger when the air hosed is
disconnected, this causes CRC to backflow into the air inlet.
• Thoroughly shake the Noxudol 300S liter before use.
• Apply all three liters of Noxudol 300S to the left and right
frames and the cross-members. (No product is allowed to
remain.)
14
G.
UNDER VEHICLE NOXUDOL 300S CRC APPLICATION
1. AFTER REVIEWING THE APPLICATION PROCESS OUTLINED BELOW, BEGIN APPLYING
NOXUDOL 300S TO THE EXTERNAL SURFACES OF THE FRAME
Step① Coat outer and bottom surfaces of right side frame. (Start from front of the vehicle)
Step②
Coat inside surfaces of right side frame. (Start from rear of vehicle)
Step③
Coat No.0, No.1, No.2, No.3, No.4, No.5, No.6, and rear cross-members from front to back. (Start from
front of vehicle)
Step④ Coat inside surfaces of left side frame. (Start from rear of vehicle)
STEP ②
Inside of Right Side Frame
STEP ④
Inside of Left Side Frame
STEP ①
Top side & Outer & Bottom
Sides of Right Side Frame
STEP ⑤
Top side & Outer & Bottom
Sides of Left Side Frame
STEP ③
No.0, No.1, No.2, No.3,
No.4, No.5, No.6,
Rear Cross-members
Discharge rate varies depending on CRC temperature. Make adjustments to spray rate as needed, but
do not change air pressure (air pressure must be 50 psi).
15
H.
RESTORE THE VEHICLE
1.
RESTORE THE VEHICLE
a) Re-install the engine undercover.
b) Re-install wheels and torque to spec.
Steel Wheel / Aluminum Wheel
Torque Spec: 113 N m (1152 kgf cm, 83 ft lbf)
c) Lower the vehicle.
d) For areas where the lift arms touched, remove any rust present
and apply Noxudol 300S.
CONFIRM ALL 3 LITERS OF NOXUDOL
300S HAVE BEEN APPLIED TO THE
EXTERNAL PORTION OF THE FRAME!
Ensure to follow the procedure and perform all steps
completely (e.g. inspection, cleaning/rust removal, CRC
application, one kit per vehicle, etc.) any deviation will be
subject to warranty claim debit.
e)
f)
g)
h)
i)
j)
k)
Raise the vehicle.
Remove all masking tape, fire retardant sheeting, and plastic coverings.
Lower the vehicle.
Install the spare tire.
Remove protective tape from the identifying labels (VIN label, etc.) on the frame.
Place a Corrosion-Resistant Compound information Hang Tag on the rear-view mirror.
Let CRC cure approximately 24 hours before returning vehicle to customer.
RECORD-KEEPING AND OTHER REQUIREMENTS
To make sure that your dealership can satisfy specific state and local requirements, please refer to your
specific state Dealer Information Packet.
APPENDIX
A. 712AM & NOXUDOL 300S DISPOSAL
712AM & Noxudol 300S used in the application of the frame CRC as well as any materials, such as
tarps with residue, must be disposed of in the same manner as other hazardous waste at your
dealership and in accordance with all applicable local, state, and federal regulations. Please refer to the
Dealer Information Packet for additional information.
B. TEMPLATES FOR FRAME SEAL INSTALL
16
Template A
Template B
Template C
Template D
38.0.23
Page 1/8
Safety Data Sheet (SDS)
OSHA Haz Com Standard 29 CFR 1910.1200. Prepared to GHS Rev03.
Printing date 03/06/2014
Reviewed on 03/06/2014
* 1 Identification
· Product identifier
· Trade name: Noxudol 300 S
· Product number: 37300
· Product description Anti Rust Compound, Vehicle Underbody Coating
· Details of the supplier of the safety data sheet
· Manufacturer/Supplier:
Manufacturer: Auson AB
Verkstadsgatan 3
S-434 42 Kungsbacka Sweden
www.auson.se
Phone: +46 300-562000
Fax: +46 300-562001
US Distributor: Soken Trade Corporation
12055 Sherman Way
North Hollywood, CA USA
www.noxudolusa.com
Phone: (818) 308-8430
Fax: (818) 308-8428
· Emergency telephone number:
For Hazardous Materials [or Dangerous Goods] Incident. Spill, Leak, Fire, Exposure, or Accident
Call CHEMTREC Day or Night
Within USA and Canada: 1-800-424-9300 CCN701762 or +1 703-527-3887 (collect calls accepted)
2 Hazard(s) identification
· Classification of the substance or mixture
Health hazard
Suspected of causing cancer.
· Label elements
· GHS label elements
The product is classified and labeled according to the Globally Harmonized System (GHS).
· Hazard pictograms
GHS08
· Signal word Warning
· Hazard-determining components of labeling:
Carbon black
· Hazard statements
Suspected of causing cancer.
· Precautionary statements
Use personal protective equipment as required.
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
IF exposed or concerned: Get medical advice/attention.
(Contd. on page 2)
38.0.23
Page 2/8
Safety Data Sheet (SDS)
OSHA Haz Com Standard 29 CFR 1910.1200. Prepared to GHS Rev03.
Printing date 03/06/2014
Reviewed on 03/06/2014
Trade name: Noxudol 300 S
(Contd. of page 1)
Store locked up.
Dispose of contents/container in accordance with local/regional/national/international regulations.
· Classification system:
· NFPA ratings (scale 0 - 4)
0
1
Health = 0
Fire = 1
Reactivity = 0
0
· HMIS-ratings (scale 0 - 4)
HEALTH
*0
FIRE
1
REACTIVITY 0
Health = *0
Fire = 1
Reactivity = 0
3 Composition/information on ingredients
· Chemical characterization: Mixtures
· Description: Mixture of the substances listed below with nonhazardous additions.
· Dangerous components:
64741-88-4 Distillates (petroleum), solvent-refined heavy paraffinic
Carc. 1B, H350
8002-74-2 Paraffin waxes and Hydrocarbon waxes
1333-86-4 Carbon black
Carc. 2, H351;
Skin Irrit. 2, H315; Eye Irrit. 2A, H319; STOT SE 3, H335
25-50%
15-35%
≤ 2.5%
4 First-aid measures
· Description of first aid measures
· After inhalation: Supply fresh air; consult doctor in case of complaints.
· After skin contact: Generally the product does not irritate the skin.
· After eye contact: Rinse opened eye for several minutes under running water.
· After swallowing: Give large amounts of water. If symptoms persist consult doctor.
· Most important symptoms and effects, both acute and delayed No further relevant information available.
· Indication of any immediate medical attention and special treatment needed
No further relevant information available.
5 Fire-fighting measures
· Extinguishing media
· Suitable extinguishing agents: Use fire fighting measures that suit the environment.
· Special hazards arising from the substance or mixture No further relevant information available.
· Advice for firefighters
· Protective equipment: No special measures required.
6 Accidental release measures
· Personal precautions, protective equipment and emergency procedures Not required.
· Environmental precautions: Do not allow to enter sewers/ surface or ground water.
· Methods and material for containment and cleaning up:
Absorb with liquid-binding material (ie. sand, diatomite, acid binders, universal binders, sawdust).
Dispose contaminated material as waste according to section 13.
Ensure adequate ventilation.
(Contd. on page 3)
38.0.23
Page 3/8
Safety Data Sheet (SDS)
OSHA Haz Com Standard 29 CFR 1910.1200. Prepared to GHS Rev03.
Printing date 03/06/2014
Reviewed on 03/06/2014
Trade name: Noxudol 300 S
(Contd. of page 2)
· Reference to other sections
See Section 7 for information on safe handling.
See Section 8 for information on personal protection equipment.
See Section 13 for disposal information.
7 Handling and storage
· Precautions for safe handling
Ensure good ventilation/exhaustion at the workplace.
Open and handle receptacle with care.
Prevent formation of aerosols.
· Information about protection against explosions and fires:
Do not spray on a naked flame or any incandescent material.
Keep protective respiratory device available.
· Conditions for safe storage, including any incompatibilities
· Storage:
· Requirements to be met by storerooms and receptacles: No special requirements.
· Information about storage in one common storage facility: Not required.
· Further information about storage conditions: None.
· Specific end use(s) No further relevant information available.
8 Exposure controls/personal protection
· Additional information about design of technical systems: No further data; see section 7.
· Control parameters
· Components with limit values that require monitoring at the workplace:
8002-74-2 Paraffin waxes and Hydrocarbon waxes
REL Long-term value: 2 mg/m³
TLV Long-term value: 2 mg/m³
1333-86-4 Carbon black
PEL Long-term value: 3.5 mg/m³
REL Long-term value: 3.5* mg/m³
*0.1 in presence of PAHs;See Pocket Guide Apps.A+C
TLV Long-term value: 3* mg/m³
*inhalable fraction
· Additional information: The lists that were valid during the creation were used as basis.
· Exposure controls
· Personal protective equipment:
· General protective and hygienic measures:
Keep away from foodstuffs, beverages and feed.
Immediately remove all soiled and contaminated clothing.
Wash hands before breaks and at the end of work.
Store protective clothing separately.
· Breathing equipment: Not required.
· Protection of hands:
Protective gloves
(Contd. on page 4)
38.0.23
Page 4/8
Safety Data Sheet (SDS)
OSHA Haz Com Standard 29 CFR 1910.1200. Prepared to GHS Rev03.
Printing date 03/06/2014
Reviewed on 03/06/2014
Trade name: Noxudol 300 S
(Contd. of page 3)
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/
the chemical mixture.
Select glove material based on penetration times, rates of diffusion and degradation.
· Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality
and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the
resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the
application.
· Penetration time of glove material
The exact break-through time has to be determined and observed by the manufacturer of the protective
gloves.
· Eye protection: Tightly sealed goggles
* 9 Physical and chemical properties
· Information on basic physical and chemical properties
· General Information
· Appearance:
Highly viscous
Form:
Black
Color:
· Odor:
Mineral-oil-like
· Odor threshold:
Not determined.
· pH-value:
Not determined.
· Change in condition
Melting point/Melting range:
Boiling point/Boiling range:
Not determined.
316 °C (601 °F)
· Flash point:
140 °C (284 °F)
· Flammability (solid, gaseous):
Not applicable.
· Ignition temperature:
300 °C (572 °F)
· Decomposition temperature:
Not determined.
· Auto igniting:
Product is not selfigniting.
· Danger of explosion:
Product does not present an explosion hazard.
· Explosion limits:
Lower:
Upper:
Not determined.
Not determined.
· Vapor pressure:
Not determined.
· Density @ 20 °C (68 °F):
· Relative density
· Vapour density
· Evaporation rate
0.96 g/cm³ (8.011 lbs/gal)
Not determined.
Not determined.
Not determined.
· Solubility in / Miscibility with
Water:
Not miscible or difficult to mix.
· Partition coefficient (n-octanol/water): Not determined.
· Viscosity:
Dynamic @ 20 °C (68 °F):
500650 mPas
(Contd. on page 5)
38.0.23
Page 5/8
Safety Data Sheet (SDS)
OSHA Haz Com Standard 29 CFR 1910.1200. Prepared to GHS Rev03.
Printing date 03/06/2014
Reviewed on 03/06/2014
Trade name: Noxudol 300 S
(Contd. of page 4)
Kinematic:
Not determined.
· Solvent content:
Organic solvents:
VOC content:
0.0 %
10.7 g/l / 0.09 lb/gl
Solids content:
· Other information
98.0 %
No further relevant information available.
10 Stability and reactivity
· Reactivity No further relevant information available.
· Chemical stability
· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.
· Possibility of hazardous reactions No dangerous reactions known.
· Conditions to avoid No further relevant information available.
· Incompatible materials: No further relevant information available.
· Hazardous decomposition products: No dangerous decomposition products known.
11 Toxicological information
· Information on toxicological effects
· Acute toxicity:
· LD/LC50 values that are relevant for classification:
1333-86-4 Carbon black
Oral LD50 10000 mg/kg (rat)
· Primary irritant effect:
· on the skin: No irritant effect.
· on the eye: No irritating effect.
· Sensitization: No sensitizing effects known.
· Additional toxicological information:
The product shows the following dangers according to internally approved calculation methods for
preparations:
Carcinogenic.
· Carcinogenic categories
· IARC (International Agency for Research on Cancer)
1333-86-4 Carbon black
14808-60-7 Quartz (SiO2)
2B
1
· NTP (National Toxicology Program)
14808-60-7 Quartz (SiO2)
K
12 Ecological information
· Toxicity
· Aquatic toxicity: No further relevant information available.
· Persistence and degradability No further relevant information available.
· Bioaccumulative potential No further relevant information available.
· Mobility in soil No further relevant information available.
· Additional ecological information:
· General notes:
Water hazard class 3 (Self-assessment): extremely hazardous for water
Do not allow product to reach ground water, water course or sewage system, even in small quantities.
(Contd. on page 6)
38.0.23
Page 6/8
Safety Data Sheet (SDS)
OSHA Haz Com Standard 29 CFR 1910.1200. Prepared to GHS Rev03.
Printing date 03/06/2014
Reviewed on 03/06/2014
Trade name: Noxudol 300 S
(Contd. of page 5)
Danger to drinking water if even extremely small quantities leak into the ground.
· Results of PBT and vPvB assessment
· PBT: Not applicable.
· vPvB: Not applicable.
· Other adverse effects No further relevant information available.
13 Disposal considerations
· Waste treatment methods
· Recommendation:
Must not be disposed of together with household garbage. Do not allow product to reach sewage system.
· Uncleaned packagings:
· Recommendation: Disposal must be made according to official regulations.
* 14 Transport information
· UN-Number
· DOT, ADR, ADN, IMDG, IATA
· UN proper shipping name
· DOT, ADR, ADN, IMDG, IATA
· Transport hazard class(es)
Non-Regulated Material
Non-Regulated Material
· DOT, ADR, ADN, IMDG, IATA
· Class
Non-Regulated Material
· Packing group
· DOT, ADR, IMDG, IATA
Non-Regulated Material
· Environmental hazards:
· Marine pollutant:
No
· Special precautions for user
Not applicable.
· Transport in bulk according to Annex II of
Not applicable.
MARPOL73/78 and the IBC Code
· UN "Model Regulation":
-
15 Regulatory information
· Safety, health and environmental regulations/legislation specific for the substance or mixture
· Sara
· Section 355 (extremely hazardous substances):
None of the ingredients is listed.
· Section 313 (Specific toxic chemical listings):
None of the ingredients is listed.
· TSCA (Toxic Substances Control Act):
All ingredients are listed.
· Proposition 65
· Chemicals known to cause cancer:
1333-86-4 Carbon black
14808-60-7 Quartz (SiO2)
· Chemicals known to cause reproductive toxicity for females:
None of the ingredients is listed.
(Contd. on page 7)
38.0.23
Page 7/8
Safety Data Sheet (SDS)
OSHA Haz Com Standard 29 CFR 1910.1200. Prepared to GHS Rev03.
Printing date 03/06/2014
Reviewed on 03/06/2014
Trade name: Noxudol 300 S
(Contd. of page 6)
· Chemicals known to cause reproductive toxicity for males:
None of the ingredients is listed.
· Chemicals known to cause developmental toxicity:
None of the ingredients is listed.
· Carcinogenic categories
· EPA (Environmental Protection Agency)
None of the ingredients is listed.
· TLV (Threshold Limit Value established by ACGIH)
1333-86-4 Carbon black
14808-60-7 Quartz (SiO2)
A4
A2
· NIOSH-Ca (National Institute for Occupational Safety and Health)
1333-86-4 Carbon black
14808-60-7 Quartz (SiO2)
· OSHA-Ca (Occupational Safety & Health Administration)
Corrosive to eyes
· GHS label elements
The product is classified and labeled according to the Globally Harmonized System (GHS).
· Hazard pictograms
GHS08
· Signal word Warning
· Hazard-determining components of labeling:
Carbon black
· Hazard statements
Suspected of causing cancer.
· Precautionary statements
Use personal protective equipment as required.
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
IF exposed or concerned: Get medical advice/attention.
Store locked up.
Dispose of contents/container in accordance with local/regional/national/international regulations.
· National regulations:
The product is subject to be labeled according with the prevailing version of the regulations on hazardous
substances.
· State Right to Know
64741-88-4 Distillates (petroleum), solvent-refined heavy paraffinic
Carc. 1B, H350
8002-74-2 Paraffin waxes and Hydrocarbon waxes
25-50%
15-35%
(Contd. on page 8)
38.0.23
Page 8/8
Safety Data Sheet (SDS)
OSHA Haz Com Standard 29 CFR 1910.1200. Prepared to GHS Rev03.
Printing date 03/06/2014
Reviewed on 03/06/2014
Trade name: Noxudol 300 S
(Contd. of page 7)
1333-86-4 Carbon black
Carc. 2, H351;
Skin Irrit. 2, H315; Eye Irrit. 2A, H319; STOT SE 3, H335
14808-60-7 Quartz (SiO2)
Carc. 1A, H350; STOT RE 1, H372;
Acute Tox. 4, H332; STOT SE 3, H335;
Eye Irrit. 2B, H320
All ingredients are listed.
≤ 2.5%
≤ 2.5%
· Information about limitation of use:
Workers are not allowed to be exposed to the hazardous carcinogenic materials contained in this preparation.
Exceptions can be made by the authorities in certain cases.
· Chemical safety assessment: A Chemical Safety Assessment has not been carried out.
16 Other information
This information is based on our present knowledge. However, this shall not constitute a guarantee for any
specific product features and shall not establish a legally valid contractual relationship.
· Date of preparation / last revision 03/06/2014 / 5
· Abbreviations and acronyms:
ADR: Accord européen sur le transport des marchandises dangereuses par Route (European Agreement concerning the International
Carriage of Dangerous Goods by Road)
IMDG: International Maritime Code for Dangerous Goods
DOT: US Department of Transportation
IATA: International Air Transport Association
ACGIH: American Conference of Governmental Industrial Hygienists
EINECS: European Inventory of Existing Commercial Chemical Substances
ELINCS: European List of Notified Chemical Substances
CAS: Chemical Abstracts Service (division of the American Chemical Society)
NFPA: National Fire Protection Association (USA)
HMIS: Hazardous Materials Identification System (USA)
VOC: Volatile Organic Compounds (USA, EU)
LC50: Lethal concentration, 50 percent
LD50: Lethal dose, 50 percent
Skin Irrit. 2: Skin corrosion/irritation, Hazard Category 2
Eye Irrit. 2A: Serious eye damage/eye irritation, Hazard Category 2A
Carc. 1B: Carcinogenicity, Hazard Category 1B
Carc. 2: Carcinogenicity, Hazard Category 2
STOT SE 3: Specific target organ toxicity - Single exposure, Hazard Category 3
· * Data compared to the previous version altered.
SDS / MSDS Created by MSDS Authoring Services (www.MSDSAuthoring.com)
SAFETY DATA SHEET
1. Identification
Product identifier
NOX-RUST 712AM
Other means of identification
SDS number
140017
Recommended use
Rust preventing oil.
Recommended restrictions
None known.
Manufacturer / Importer / Supplier / Distributor information
Supplier
Address
Telephone
Contact person
e-mail
Emergency phone number
Parker Industries, Inc.
15-1, Nihonbashi 1-chome, Chuo-ku, Tokyo 103-0027 JAPAN
+81 (3) 5205-1971
Noriharu Tanaka
[email protected]
+81-47-431-3598
2. Hazard(s) identification
Physical hazards
Not classified.
Health hazards
Not classified.
Environmental hazards
Not classified.
OSHA defined hazards
Not classified.
Label elements
Hazard symbol
None.
Signal word
Not available.
Hazard statement
Not available.
Precautionary statement
Prevention
Observe good industrial hygiene practices.
Response
Wash skin with soap and water.
Storage
Store in a closed container.
Disposal
Dispose of waste and residues in accordance with local authority requirements.
Hazard(s) not otherwise
classified (HNOC)
None known.
3. Composition/information on ingredients
Mixtures
Chemical name
CAS number
%
Mineral oil
Proprietary
<60
Rust preventive additive
Proprietary
<10
Composition comments
All concentrations are in percent by weight unless ingredient is a gas. Gas concentrations are in
percent by volume.
4. First-aid measures
Inhalation
Move to fresh air. Get medical attention if any discomfort continues.
Skin contact
Rinse with water. Get medical attention if irritation persists after washing.
Eye contact
Rinse the eye with water immediately. Get medical attention if irritation develops and persists.
Ingestion
Rinse mouth thoroughly. Get medical attention if any discomfort continues.
Most important
symptoms/effects, acute and
delayed
Prolonged contact may cause dryness of the skin.
Indication of immediate
medical attention and special
treatment needed
Treat symptomatically.
General information
First aid personnel must be aware of own risk during rescue.
NOX-RUST 712AM
919277 Version #: 01
SDS US
Revision date: -
Issue date: 06-March-2014
1/6
5. Fire-fighting measures
Suitable extinguishing media
Use fire-extinguishing media appropriate for surrounding materials.
Unsuitable extinguishing
media
None known.
Specific hazards arising from
the chemical
By heating and fire, toxic vapors/gases may be formed.
Special protective equipment
and precautions for firefighters
Fire-fighting
equipment/instructions
Selection of respiratory protection for firefighting: follow the general fire precautions indicated in
the workplace. Self-contained breathing apparatus and full protective clothing must be worn in
case of fire.
Use standard firefighting procedures and consider the hazards of other involved materials. Prevent
runoff from fire control or dilution from entering streams, sewers, or drinking water supply.
General fire hazards
Will burn if involved in a fire.
6. Accidental release measures
Personal precautions,
protective equipment and
emergency procedures
Wear suitable protective clothing, gloves and eye/face protection. Avoid prolonged and repeated
contact.
Methods and materials for
containment and cleaning up
Absorb spillage with suitable absorbent material.
Environmental precautions
Avoid discharge into drains, water courses or onto the ground.
7. Handling and storage
Precautions for safe handling
Avoid prolonged and repeated contact. Observe good industrial hygiene practices.
Conditions for safe storage,
including any incompatibilities
Store in a well-ventilated place. Keep container tightly closed. Store away from incompatible
materials.
8. Exposure controls/personal protection
Occupational exposure limits
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
Components
Type
Value
Form
Mineral oil (CAS
Proprietary)
Rust preventive additive
(CAS Proprietary)
PEL
5 mg/m3
Mist.
PEL
5 mg/m3
Respirable fraction.
15 mg/m3
Total dust.
US. ACGIH Threshold Limit Values
Components
Type
Value
Form
Mineral oil (CAS
Proprietary)
TWA
5 mg/m3
Inhalable fraction.
US. NIOSH: Pocket Guide to Chemical Hazards
Components
Type
Value
Form
Mineral oil (CAS
Proprietary)
STEL
10 mg/m3
Mist.
TWA
TWA
5 mg/m3
5 mg/m3
Mist.
Respirable.
10 mg/m3
Total
Rust preventive additive
(CAS Proprietary)
Biological limit values
No biological exposure limits noted for the ingredient(s).
Appropriate engineering
controls
Provide adequate ventilation. Observe occupational exposure limits and minimize the risk of
inhalation of vapors and mist.
Individual protection measures, such as personal protective equipment
Risk of splashes: Wear approved safety goggles.
Eye/face protection
Skin protection
Hand protection
Respiratory protection
Thermal hazards
NOX-RUST 712AM
919277 Version #: 01
For prolonged or repeated skin contact use suitable protective gloves.
Wear appropriate clothing to prevent repeated or prolonged skin contact.
Other
In case of inadequate ventilation or risk of inhalation of oil mist, suitable respiratory equipment with
particulate filter and organic vapor cartridges can be used.
Wear appropriate thermal protective clothing, when necessary.
SDS US
Revision date: -
Issue date: 06-March-2014
2/6
Always observe good personal hygiene measures, such as washing after handling the material
and before eating, drinking, and/or smoking. Routinely wash work clothing and protective
equipment to remove contaminants.
General hygiene
considerations
9. Physical and chemical properties
Viscous liquid.
Appearance
Physical state
Liquid.
Form
Viscous liquid.
Color
Yellowish brown.
Odor
Fatty. Oily.
Odor threshold
Not available.
pH
Not available.
Melting point/freezing point
Not available.
Initial boiling point and boiling
range
> 482 °F (> 250 °C)
Flash point
> 410.0 °F (> 210.0 °C)
Evaporation rate
Not available.
Flammability (solid, gas)
Not applicable.
Upper/lower flammability or explosive limits
Not available.
Flammability limit - lower
(%)
Flammability limit - upper
(%)
Not available.
Vapor pressure
Not available.
Vapor density
Not available.
Relative density
0.9 - 1
Solubility(ies)
Solubility (water)
Not available.
Partition coefficient
(n-octanol/water)
Not available.
Auto-ignition temperature
Not available.
Decomposition temperature
Not available.
Viscosity
1000 mPa·s (20 °C)
10. Stability and reactivity
Reactivity
The product is non-reactive under normal conditions of use, storage and transport.
Chemical stability
Stable under normal temperature conditions.
Possibility of hazardous
reactions
Will not occur.
Conditions to avoid
Contact with incompatible materials.
Incompatible materials
Strong oxidizing agents.
Hazardous decomposition
products
Carbon oxides. Sulfur dioxide. Nitrogen oxides. Calcium oxides.
11. Toxicological information
Information on likely routes of exposure
May cause discomfort if swallowed.
Ingestion
Inhalation
Under normal conditions of intended use, this material is not expected to be an inhalation hazard.
Skin contact
Prolonged contact may cause dryness of the skin.
Eye contact
May cause temporary eye irritation. May cause redness and pain.
Symptoms related to the
physical, chemical and
toxicological characteristics
Prolonged contact may cause dryness of the skin.
Information on toxicological effects
Acute toxicity
NOX-RUST 712AM
919277 Version #: 01
May cause discomfort if swallowed.
SDS US
Revision date: -
Issue date: 06-March-2014
3/6
Components
Species
Test Results
Rust preventive additive (CAS Proprietary)
Acute
Oral
LD50
Mouse
6450 mg/kg
Rat
6450 mg/kg
Skin corrosion/irritation
Prolonged contact may cause dryness of the skin.
Serious eye damage/eye
irritation
May cause temporary eye irritation. May cause redness and pain.
Respiratory or skin sensitization
No data available.
Respiratory sensitization
No data available.
Skin sensitization
Germ cell mutagenicity
No data available.
Carcinogenicity
No data available.
Reproductive toxicity
No data available.
Specific target organ toxicity single exposure
No data available.
Specific target organ toxicity repeated exposure
No data available.
Aspiration hazard
No data available.
Chronic effects
No data available.
12. Ecological information
Persistence and degradability
The product components are not classified as environmentally hazardous. However, this does not
exclude the possibility that large or frequent spills can have a harmful or damaging effect on the
environment.
No data available.
Bioaccumulative potential
No data available.
Mobility in soil
No data available.
Mobility in general
No data available.
Other adverse effects
No data available.
Ecotoxicity
13. Disposal considerations
Disposal instructions
Dispose of in accordance with local regulations.
Hazardous waste code
The waste code should be assigned in discussion between the user, the producer and the waste
disposal company.
Dispose in accordance with all applicable regulations. Do not discharge into drains, water courses
or onto the ground.
Waste from residues / unused
products
Contaminated packaging
Since emptied containers may retain product residue, follow label warnings even after container is
emptied.
14. Transport information
DOT
Not regulated as dangerous goods.
IATA
Not regulated as dangerous goods.
IMDG
Not regulated as dangerous goods.
Not applicable.
Transport in bulk according to
Annex II of MARPOL 73/78 and
the IBC Code
15. Regulatory information
US federal regulations
This product is not known to be a "Hazardous Chemical" as defined by the OSHA Hazard
Communication Standard, 29 CFR 1910.1200.
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
US. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not listed.
NOX-RUST 712AM
919277 Version #: 01
SDS US
Revision date: -
Issue date: 06-March-2014
4/6
CERCLA Hazardous Substance List (40 CFR 302.4)
Not listed.
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Immediate Hazard - No
Hazard categories
Delayed Hazard - No
Fire Hazard - No
Pressure Hazard - No
Reactivity Hazard - No
SARA 302 Extremely hazardous substance
Not listed.
SARA 311/312 Hazardous
chemical
No
SARA 313 (TRI reporting)
Not regulated.
Other federal regulations
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Not regulated.
Safe Drinking Water Act
(SDWA)
US state regulations
US. Massachusetts RTK - Substance List
Mineral oil (CAS Proprietary)
Rust preventive additive (CAS Proprietary)
US. New Jersey Worker and Community Right-to-Know Act
Mineral oil (CAS Proprietary)
Rust preventive additive (CAS Proprietary)
US. Pennsylvania Worker and Community Right-to-Know Law
Rust preventive additive (CAS Proprietary)
US. Rhode Island RTK
Not regulated.
US. California Proposition 65
California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain
any chemicals currently listed as carcinogens or reproductive toxins.
US - California Proposition 65 - Carcinogens & Reproductive Toxicity (CRT): Listed substance
Not listed.
International Inventories
Country(s) or region
Australia
Inventory name
Australian Inventory of Chemical Substances (AICS)
On inventory (yes/no)*
Yes
Canada
Domestic Substances List (DSL)
Canada
Non-Domestic Substances List (NDSL)
China
Inventory of Existing Chemical Substances in China (IECSC)
Yes
Korea
Existing Chemicals List (ECL)
Yes
New Zealand
New Zealand Inventory
Yes
United States & Puerto Rico
Toxic Substances Control Act (TSCA) Inventory
Yes
Yes
No
*A "Yes" indicates this product complies with the inventory requirements administered by the governing country(s).
A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
country(s).
16. Other information, including date of preparation or last revision
Issue date
06-March-2014
Revision date
-
Version #
01
NOX-RUST 712AM
919277 Version #: 01
SDS US
Revision date: -
Issue date: 06-March-2014
5/6
NFPA Ratings
1
1
Disclaimer
NOX-RUST 712AM
919277 Version #: 01
0
This information is provided without warranty. The information is believed to be correct. This
information should be used to make an independent determination of the methods to safeguard
workers and the environment.
SDS US
Revision date: -
Issue date: 06-March-2014
6/6