TS-S120 Rev.01

SERVICE BULLETIN
Bulletin Type............: Safety Recall
Bulletin No...............: TS-S120 (Rev01)
Bulletin Name..........: Fasteners and Bracket of Leveling
Valve Linkage System
Subject: Fasteners and Bracket of Leveling
Valve Linkage System
Summary: This safety recall technical service
bulletin gives instruction about how to remedy
your vehicle.
Bulletin Ref No.........: 700003234
NHTSA…………….........: 17V310
Rev. Details: This bulletin has been revised to
add visual inspection process of the tag axle
tires.
Release Date..........: 28.12.2017
Bulletin Responsible: Fikret ÖZCAN
Vehicle Model..........: TS45
Published by&Approved by: Hakan GÜNERDEM
Revision No…………….: 01
Fiat Rate Code..........: TSS120
Flat Rate Time..........: 75’
Welding on the Chassis
• Always disconnect the batteries (starting with the negative lead).
• Disconnect the connectors of electrical and electronic equipment (electronic control units, sensors and
actuators) if they are less than 2 meters away from the chassis part to be welded or the earth terminal of the
welding equipment.
• The earth terminal should never be attached to vehicle components such as engine, axles and springs. Arcing
on these parts is not permitted, because of the risk of damage to bearings, springs, etc.
• The earth terminal must make good contact and be placed as close as possible to the part to be welded.
• Plastic pipes, rubber parts and parabolic springs should be well protected against welding spatter and
temperatures higher than 70°.
• The contact switch must not be in the accessory or contact position. The contact key should be removed.
TS-S120 Rv01 1 / 6
SERVICE BULLETIN
GENERAL PRECAUTIONS
1. Suggested Dress Code:
2. Before Starting the Work:
Always wear protective clothing. Do not wear any damaged or loose-fitting clothing
and remove jewelry before starting the work. In case of long hair use hairnet.
The illustration above shows some of the correct and incorrect clothing that should
be worn during work. Sharp edges should be avoided e.g belts, watches, necklaces etc.
3. Interior materials protection:
Seats, trimming, upholstery stuff and carpeting should be protected with appropriate
coverings.
TS-S120 Rv01 2 / 6
SERVICE BULLETIN
Included Parts List
No
Part No
Part Name
1
Picture
Qty
Unit
RP316115Y
BRACKET,
LEVELING VALVE
LEFT
1
Pc
2
RP316114Y
BRACKET,
LEVELING VALVE
RIGHT
1
Pc
3
BCMB08030B30Y
BOLT
4
Pcs
4
MF450005Y
WASHER,PLAIN (A
8.4)
10
Pcs
5
MF430005Y
NUT, AKB
(M8X1.25)
4
Pcs
6
MF450405Y
SPRING LOCK
WASHER (B 8)
6
Pcs
7
MF101257Y
BOLT,AKB(M8x25)
2
Pcs
TS-S120 Rv01 3 / 6
SERVICE BULLETIN
Application:
1-Open the fender:
2- Dismount the shock absorber's lower nut;
Dismount the shock absorber
TS-S120 Rv01 4 / 6
SERVICE BULLETIN
3- Dismount the current bracket's bolt which is marked with red arrow and mount the
new bolt (MF101257Y) with using spring lock washer and washer.
MF101257Y
4- Mark the points where the new reinforcement bracket's holes coincide on the leveling
bracket. After marking the spots which you need to drill, drill 3/8" holes to the leveling
bracket. After drilling the holes, mount the new reinforcement bracket with bolt
(BCMB08030B30Y), spring washer (MF450405Y), plain washer (MF450005Y) and nut
(MF430005Y).
BCMB08030B30Y
TS-S120 Rv01 5 / 6
SERVICE BULLETIN
5- After the visual inspection of the tag axle tires, if the surface of the tires are
damaged then replace the damaged tire with a new one according to the Temsa tire
specifications.
6- Close the fender.
FLAT-RATE BREAK DOWN
Application
1. Preparation
2. Opening the fenders for both sides
3. Removing the shock absorbers' lower nuts
4. Drilling the new holes on leveling brackets
5. Reinforcement bracket assembly
6. Closing the fenders for both sides
Total
Time
10 Mins
15 Mins
10 Mins
10 Mins
10 Mins
20 Mins
75 Mins
TS-S120 Rv01 6 / 6