Campaign Circula

IMPORTANT INFORMATION
Please inform and provide a copy of this document to every person in your dealership with campaign-related responsibilities, including
Service, Parts and Accounting personnel. By law, dealers must correct, prior to delivery for sale or lease, any vehicle that fails to
comply with an applicable Federal Motor Vehicle Safety Standard or that contains a defect relating to motor vehicle safety. If you
have questions regarding this or any other campaign, please contact Warranty.
Emissions Service Action
Code: 23O6
Subject:
Certain 2010-2014 Volkswagen Vehicles with 2.0L TDI® Clean Diesel Engine
ECM Software Update
REVISION
June 30, 2015
Revision Summary
Warning statement added in work procedure.
Problem Description
The vehicle’s engine management software has been
improved to assure the vehicle’s tailpipe emissions are
optimized and operating efficiently. Under certain
operating conditions, the earlier strategy may have
increased the chance of the vehicle’s MIL light
illuminating. If the MIL illuminates for any reason, the
vehicle will not pass an IM emissions inspection in some
regions.
Corrective Action
Install updated ECM software.
Affected Vehicles
U.S.A. and CANADA:
2010-2014 Beetle, Beetle Convertible, Jetta, Golf,
Jetta SportWagen/Golf Wagon
with 2.0L TDI® Clean Diesel engine
Verify the open Campaigns/Actions screen in Elsa to determine if
the VIN# applies to this Campaign/Action
Owner Notification Mailing
On or about April 07, 2015, the owner mailing took place.
A sample copy of the owner letter is enclosed.
Requirements for Emissions Campaigns Having
Customer Notification (CALIFORNIA ONLY)
The California Air Resources Board and the Department of
Motor Vehicles (DMV) require emissions-related
campaigns to be completed prior to vehicle registration
renewal. When campaign work is done you must
provide the owner with a signed “Vehicle Emission
Recall – Proof of Correction” certificate (RC
EMISCAVWAU). Certificates can be ordered at no cost
online via the Compliance Label Ordering portal at
www.vwhub.com.
Campaign Completion Labeling Guidelines
Vehicles repaired under this action must be identified with
a campaign completion label (part number CAMP 010
000). Labels can be ordered at no cost online via the
Compliance Label Ordering portal at www.vwhub.com.
NOTE:
•
•
•
•
Elsa is the only valid campaign inquiry/verification source. Check
Elsa on the day the campaign work will be performed to verify vehicle
eligibility for the repair in order to receive claim payment
consideration. Campaign status must show “open”.
If this repair appears to have already been performed on the vehicle
but the code still shows open in Elsa, contact Warranty before
proceeding further, e.g. a dealer may have recently performed this
repair but not yet entered a claim for it in the system.
Elsa may also show additional open action(s); if so, inform your
customer - this work can be done while the vehicle is in for this
campaign.
Contact Warranty if you have any questions.
Inventory Vehicle Open Campaign/Action Report
(VIM)
On or about April 07, 2015, affected vehicles were listed
on the Inventory Vehicle Open Campaign Action report
under My Dealership Reports (found on www.vwhub.com
& VIM). A list was not posted for dealers who did not have
any affected vehicles.
Parts Information and Allocation
This action is a software update only; no parts are
required.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 1 of 15
Claim Entry Procedure
Immediately upon completion of the repair work, enter the Applicable Criteria ID and Repair Operation from the
following chart. The Applicable Criteria ID is shown in Elsa. Claims will only be paid for vehicles that show
this campaign open in Elsa on the day of the repair. To help ensure prompt and proper payment, attach the
screen print to the repair order.
Saga Claim Entry Procedure
Check Elsa to determine if this campaign is open.
Service No.:
Damage Code:
23O6 (Letter O, not number zero)
0099
Parts Manufacturer
Removed part: Use vendor code WWO
Sold vehicle = 7 10
Unsold vehicle = 7 90
Accounting Instructions
Criteria I.D. 01
Check/Updated software present, no further work required
Repair operation:
0183 00 99
20 T.U.
2360 25 99
50 T.U.
OR
Update ECM software.
Repair operation:
There is NO reimbursement for Vehicle Wash or Loaner
If customer refused repairs
U.S. dealers: Submit the request through WISE under the Campaigns/Update/Recall Closure option.
Canadian dealers: Fax the Repair Order to Warranty at (905) 428-4811 and provide VIN, applicable
Service Number, Customer Information, Dealer Number and Date.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 2 of 15
Customer Letter Example (United States – 49 states)
Subject:
Emissions Service Action 23O6 – ECM Software
Certain 2010-2014 Model Year Volkswagen Vehicles Equipped with a 2.0L TDI® Clean Diesel Engine
Dear Volkswagen Owner,
As part of Volkswagen's ongoing commitment to our environment, and in cooperation with the United States
Environmental Protection Agency, we are informing you of our decision to conduct an emissions service action on certain
2010-2014 model year Volkswagen vehicles equipped with a 2.0L TDI® Clean Diesel engine. Our records show that
you are the owner of a vehicle affected by this action.
What is the issue, and
what will we do?
The vehicle’s engine management software has been improved to assure your vehicle’s
tailpipe emissions are optimized and operating efficiently. Under certain operating
conditions, the earlier strategy may have increased the chance of the vehicle’s MIL light
illuminating. If the MIL illuminates for any reason, your vehicle will not pass an IM emissions
inspection in some regions.
To address this issue, your authorized Volkswagen dealer will update the ECM software in
your vehicle. This work will take about one hour to complete and will be performed for you
free of charge. Please keep in mind that your dealer may need additional time for the
preparation of the repair, as well as to accommodate their daily workshop schedule.
IMPORTANT!
Please note that if the ECM in your vehicle has been “chipped,” “tuned,” or
otherwise modified from original factory specifications with aftermarket
components and/or software, work needed to repair, replace, or return the ECM to
original factory specifications is NOT covered under this action.
What should you do?
In order to limit any possible inconvenience, please contact your authorized Volkswagen
dealer as soon as possible to schedule this service.
Lease vehicles and
address changes
If you are the lessor and registered owner of the vehicle identified in this action, please
forward this letter immediately via first-class mail to the lessee within ten (10) days of receipt.
If you have changed your address or sold the vehicle, please fill out the enclosed prepaid
Owner Reply card and mail it to us so we can update our records.
Reimbursement of
Expenses
If you have previously paid for repairs relating to the condition described in this letter, the
enclosed form explains how to request reimbursement. We would be pleased to review your
reimbursement request.
Can we assist you
further?
If your authorized Volkswagen dealer fails or is unable to complete this work free of charge
within a reasonable time, please call or write to:
Volkswagen of America, Inc.,
Attn: Customer CARE (23O6)
3800 Hamlin Road, Auburn Hills, MI 48326
1-800-893-5298
www.vw.com
Checking your vehicle
for open Recalls and
Service Campaigns
To check your vehicle’s eligibility for repair under this or any other recall/service campaign,
please visit the Recall/Service Campaign Lookup tool at www.vw.com and enter your
Vehicle Identification Number (VIN). As always, if you have any questions or if you need
additional assistance, please contact Customer CARE or your authorized Volkswagen
dealer.
We apologize for any inconvenience this matter may cause; however we are taking this action to help ensure your
vehicle continues to meet and exceed your expectations. Thank you for driving a Volkswagen!
Sincerely,
Volkswagen Customer Protection
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 3 of 15
Customer Letter Example (United States – California)
Subject:
Emissions Service Action 23O6 – ECM Software
Certain 2010-2014 Model Year Volkswagen Vehicles Equipped with a 2.0L TDI® Clean Diesel Engine
Dear Volkswagen Owner,
As part of Volkswagen's ongoing commitment to our environment, and in cooperation with the United States
Environmental Protection Agency and the California Air Resources Board, we are informing you of our decision to
conduct an emissions service action on certain 2010-2014 model year Volkswagen vehicles equipped with a 2.0L TDI®
Clean Diesel engine. Our records show that you are the owner of a vehicle affected by this action.
What is the issue, and
what will we do?
The vehicle’s engine management software has been improved to assure your vehicle’s
tailpipe emissions are optimized and operating efficiently. Under certain operating
conditions, the earlier strategy may have increased the chance of the vehicle’s MIL light
illuminating. If the MIL illuminates for any reason, your vehicle will not pass an IM emissions
inspection in some regions.
To address this issue, your authorized Volkswagen dealer will update the ECM software in
your vehicle. This work will take about one hour to complete and will be performed for you
free of charge. Please keep in mind that your dealer may need additional time for the
preparation of the repair, as well as to accommodate their daily workshop schedule.
IMPORTANT!
Please note that if the ECM in your vehicle has been “chipped,” “tuned,” or
otherwise modified from original factory specifications with aftermarket
components and/or software, work needed to repair, replace, or return the ECM to
original factory specifications is NOT covered under this action.
What should you do?
In order to limit any possible inconvenience, please contact your authorized Volkswagen
dealer as soon as possible to schedule this service.
Lease vehicles and
address changes
If you are the lessor and registered owner of the vehicle identified in this action, please
forward this letter immediately via first-class mail to the lessee within ten (10) days of receipt.
If you have changed your address or sold the vehicle, please fill out the enclosed prepaid
Owner Reply card and mail it to us so we can update our records.
Important information for
California Vehicle
Owners – California
Regulations
California regulations require that this campaign be completed prior to the time you renew
your vehicle registration. Therefore, please make sure that this campaign is completed
prior to the renewal of your vehicle registration, and that you furnish proof of completion
to the Department of Motor Vehicles (DMV) in the form of a copy of the dealer’s repair order,
including a signed “Proof of Correction” certificate. You obtain this from your dealer after the
campaign has been completed. Please retain the signed “Proof of Correction Certificate”
with your vehicle records. DO NOT MAIL THIS FORM to the DMV, unless requested.
Reimbursement of
Expenses
If you have previously paid for repairs relating to the condition described in this letter, the
enclosed form explains how to request reimbursement. We would be pleased to review your
reimbursement request.
Can we assist you
further?
If your authorized Volkswagen dealer fails or is unable to complete this work free of charge
within a reasonable time, please call or write to:
Volkswagen of America, Inc.,
Attn: Customer CARE (23O6)
3800 Hamlin Road, Auburn Hills, MI 48326
1-800-893-5298
www.vw.com
Checking your vehicle
for open Recalls and
Service Campaigns
To check your vehicle’s eligibility for repair under this or any other recall/service campaign,
please visit the Recall/Service Campaign Lookup tool at www.vw.com and enter your
Vehicle Identification Number (VIN). As always, if you have any questions or if you need
additional assistance, please contact Customer CARE or your authorized Volkswagen
dealer.
We apologize for any inconvenience this matter may cause; however we are taking this action to help ensure your
vehicle continues to meet and exceed your expectations. Thank you for driving a Volkswagen!
Sincerely,
Volkswagen Customer Protection
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 4 of 15
Customer Letter Example (CANADA)
Subject:
Emissions Service Action 23O6 – ECM Software
Certain 2010-2014 Model Year Volkswagen Vehicles Equipped with a 2.0L TDI® Clean Diesel Engine
Dear Volkswagen Owner,
This notice is sent to you in accordance with the requirements of the Canadian Environmental Protection Act, 1999.
Volkswagen has determined that a defect, which relates to a prescribed emission standard, exists in certain 2010-2014
model year Volkswagen vehicle equipped with a 2.0L TDI® Clean Diesel engine. Our records show that you are the
owner of a vehicle affected by this action.
What is the issue, and
what will we do?
The vehicle’s engine management software has been improved to assure your vehicle’s
tailpipe emissions are optimized and operating efficiently. Under certain operating
conditions, the earlier strategy may have increased the chance of the vehicle’s MIL light
illuminating. If the MIL illuminates for any reason, your vehicle will not pass an IM emissions
inspection in some regions.
To address this issue, your authorized Volkswagen dealer will update the ECM software in
your vehicle. This work will take about one hour to complete and will be performed for you
free of charge. Please keep in mind that your dealer may need additional time for the
preparation of the repair, as well as to accommodate their daily workshop schedule.
IMPORTANT!
Please note that if the ECM in your vehicle has been “chipped,” “tuned,” or
otherwise modified from original factory specifications with aftermarket
components and/or software, work needed to repair, replace, or return the ECM to
original factory specifications is NOT covered under this action.
What should you do?
In order to limit any possible inconvenience, please contact your authorized Volkswagen
dealer as soon as possible to schedule this service. On or about April 07, 2015 the
necessary repair instructions will be available to your authorized Volkswagen dealer.
Lease vehicles and
address changes
If you are the lessor and registered owner of the vehicle identified in this action, please
forward this letter immediately via first-class mail to the lessee within ten (10) days of receipt.
If you have changed your address or sold the vehicle, please fill out the enclosed prepaid
Owner Reply card and mail it to us so we can update our records.
Reimbursement of
Expenses
If you have previously paid for repairs relating to the condition described in this letter, the
enclosed form explains how to request reimbursement. We would be pleased to review your
reimbursement request.
Can we assist you
further?
If your authorized Volkswagen dealer fails or is unable to complete this work free of charge
within a reasonable time, please call or write to:
Volkswagen Canada
Attn: Customer Relations (23O6)
PO Box 842, Stn. A
Windsor, ON N9A 6P2
1-800-822-8987
www.vw.ca
We apologize for any inconvenience this matter may cause; however we are taking this action to help ensure your
vehicle continues to meet and exceed your expectations. Thank you for driving a Volkswagen!
Sincerely,
Volkswagen Customer Protection
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 5 of 15
Campaign Work Procedure
23O6 Emissions Service Action
Required Tools:
•
VAS 6150C Scan Tool (or equivalent)
•
INC-940 Battery Charger (or
equivalent)
Required Parts:
NONE – Software update only
Work Procedure
TIP
If Campaign Completion label is present,
no further work is required
Section A – Check for Previous Repair
•
Enter the VIN in Elsa and proceed to the
“Campaign/Action” screen
TIP
On the date of repair, print this screen and keep
a copy with the repair order
⇐ Ensure that the Status is “Open”

⇐ Note the Applicable Criteria ID
 for use in determining the
correct work to be done and
corresponding parts associated
Proceed to Section B
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 6 of 15
Section B – Update ECM Software
WARNING
The software installed during this Service Action will NOT actively resolve any DTCs. All DTCs must be
diagnosed and repaired prior to performing this software update.
NOTE
Prior to launching VAS Diagnostic Device application and starting control module update process, confirm
tester screen saver and power settings are off.
Failure to do so may result in the tester entering power save mode during data transfer, and subsequent
control module failure.
When using any tester in conjunction with a VAS 5054A wireless transmitter head for a flash procedure:
•
Connect the tester using an Ethernet “hard line” cable between the tester and the on-line network.
DO NOT USE WI-FI.
•
Connect a USB cable between the transmitter head and the tester. Failure to do so may lead to
errors during the flash procedure.
•
DISABLE BLUETOOTH and ensure that the tester is NOT communicating via Bluetooth as
the Bluetooth protocol is not a robust data transfer environment for the flash process. DO
NOT USE BLUETOOTH for flashing. Control module failures caused by flashing via
Bluetooth will not be covered.
All Volkswagen scan tool devices must only be used with their power adapters plugged in. Under no
circumstances should they be used on battery power alone during the programming procedure.
Critical Warning: The Midtronics Battery Charger must be connected to the vehicle battery for the
duration of the programming, to ensure the battery state of charge remains above 12.5 volts during the
update process. If the battery drops below 12.5 volts, the programming could fail which may result in
damage to the control module.
The technician should verify the vehicle voltage prior to starting the update process, and should monitor
the voltage for the duration of the update.
Control modules damaged by insufficient voltage will not be covered.
WARNING
Radiator Fan(s) may cycle ON high speed during the Update Process! There is a serious risk that
personal injury may result if contact is made with spinning fan blades. Keep hands and all objects away
from Radiator Fan(s) during Update Process!
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 7 of 15
SVM Update Instructions
•
Switch the ignition OFF.
•
Switch off the headlights, radio, HVAC,
and all other battery consumers.
•
Open the hood.
•
If necessary, open/remove the battery
cover.
•
Connect the battery charger to the vehicle.
•
Connect the VAS tester to the online
network using an Ethernet cable.
•
Connect the VAS 5054A transmitter head
to the VAS tester using the USB cable.
•
Disable the Bluetooth by physically turning
the switch to the “off” position.
NOTE
If the Bluetooth wireless VAS 5054A transmitter
head is used in conjunction with a VAS tester,
the transmitter head MUST BE connected with a
USB cable to the tester.
WARNING
The Bluetooth function of the scan tool MUST
BE PHYSICALLY SWITCHED OFF prior to
performing this update. 
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 8 of 15
Prerequisites for SVM software update
1. Ensure the customer’s vehicle condition matches
the conditions stated in the Campaign Circular.
2. Ensure the user has a valid GeKo ID and
password.
3. Only perform operations explicitly stated in the
Campaign Circular.
4. Ensure that the following tester requirements are
met:
•
Off-board Diagnostic Information System
Service (ODIS) is installed and up to date.
•
VAS tester is plugged into a 120V AC
power supply at all times.
•
The VAS tester is connected, via wired
connection, to the internet.
•
The VAS tester is connected via USB cable
to the VAS5054A Bluetooth head PRIOR to
launching the ODIS program.
CAUTION
Prior to launching the ODIS application and
starting the control module update process,
confirm the tester screensaver and power
settings are in accordance with Special Tools
and Equipment - Service Information Document
# VSE-08-18. Failure to do so may result in the
tester entering power save mode during data
transfer andsubsequent control module failure.
When performing a flash procedure using a VAS
tester in conjunction with a VAS 5054A wireless
transmitter head, please connect a USB cable
between the transmitter head and the tester.
Failure to do so may lead to errors during the
flash procedure and may damage control
modules.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 9 of 15
⇐ Install the inCharge 940 battery tester onto
the vehicle, switch the tester on, then
select the “manual” option .
•
Follow the on screen prompts to charge
the battery during the SVM procedure.
•
Switch the ignition on.
•
Apply the parking brake.
•
Switch the headlights off.
•
Attach an appropriate VAS tester to the
vehicle.
•
Start the ODIS program.
⇐ Upon ODIS startup, verify the “Diagnosis”
operating mode is selected .
•
Using ODIS, perform a Guided Fault
Finding scan of the vehicle.
NOTE
If GFF does not interrogate all control modules,
manually select and interrogate remaining
modules before proceeding. Address or record
all DTCs related to a customer concern before
continuing. Sporadic communication DTCs will
be created during the flash procedure and must
be erased with all other sporadic DTCs by GFF
after exiting the flash test plan.
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 10 of 15
WARNING
The software installed during this Service Action
will NOT actively resolve any DTCs. All DTCs
must be diagnosed and repaired prior to
performing this software update.
⇐ Once the GFF scan is complete, select
“Special functions” , then “Adapting
Software” , then select “Perform
test” .
⇐ Select the appropriate option to update
“through measures code” .
NOTE
Read this screen carefully. The option to update
software through measures code is NOT always
selection #1 on this screen.
⇐ Enter “3339” .
⇐ Select “Accept” .
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 11 of 15
Model
Year
Transmission
Software Change Table
Original ECM
New ECM
Part Number
Software
Part Number
Software
(or higher)
2014
Manual
Auto
Manual
Auto
Manual
Auto
03L 906 019 JS
03L 906 019 JT
03L 906 019 KA
03L 906 019 KB
03L 906 019 KD
03L 906 019 KC
All
All
All
All
All
All
03L 906 019 JS
03L 906 019 JT
03L 906 019 KA
03L 906 019 KB
03L 906 019 KD
03L 906 019 KC
8183
8184
8185
8186
8182
8181
2013
Manual
Auto
Manual
Auto
Manual
Auto
03L 906 019 HE
03L 906 019 HD
03L 906 019 HB
03L 906 019 HC
03L 906 019 AN
03L 906 019 AP
All
All
All
All
All
All
03L 906 019 HE
03L 906 019 HD
03L 906 019 HB
03L 906 019 HC
03L 906 019 AN
03L 906 019 AP
8174
8175
8169
8170
8171
8172
Manual
03L 906 019 EE
03L 906 019 EF
03L 906 019 HG
03L 906 019 EH
03L 906 019 HH
03L 906 019 EG
All
03L 906 019 EE
8177
All
03L 906 019 HG
8178
All
03L 906 019 EH
8179
All
03L 906 019 HH
8180
03L 906 022 KB
03L 906 022 PB
03L 906 019 DB
03L 906 019 DA
All
All
All
All
03L 906 022 KB
03L 906 022 PB
03L 906 019 DB
03L 906 019 DA
9971
9971
9971
9971
All
03L 906 019 CM
9971
All
03L 906 019 CL
9971
Auto
2012
Manual
Auto
2011
Manual
Auto
Auto
Manual
Auto
2010
Manual
03L 906 019 CM
03L 906 022 TT
03L 906 019 CL
03L 906 022 TS
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 12 of 15
⇐ Compare the old and new part number and
software version.
⇐ If the old and new software versions
displayed are the same. Work Complete,
proceed to Section C
⇐ If the old and new software versions
displayed are different, Select “Yes” and
follow the on-screen prompts to complete
the test plan.
•
Reference the ECM Software Change
Table above for affected ECMs.
⇐ When the SVM update is complete a
confirmation message is displayed .
⇐ Select “Complete/Continue” .
⇐ Switch the ignition off, then select
“Complete/Continue” .
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 13 of 15
⇐ Switch the ignition on, then select
“Complete/Continue” .
⇐ Select “Complete/Continue” .
•
The green check mark indicates the test
plan was successfully carried out.
•
Release the parking brake.
•
Disconnect the VAS tester.
•
Switch off and disconnect the inCharge
940.
•
Reinstall the battery cover.
•
Close the hood.
Work Complete – Proceed to Section C
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 14 of 15
Section C – Campaign Completion Label
Install Campaign Completion Label
•
Open the hood.
•
Fill out and affix Campaign Completion label,
part number CAMP 010 000, next to the vehicle
emission control information label
TIP
Ensure Campaign Completion label does not
cover any existing label(s)
•
Close the hood.
California Only – Continue to Section D
Section D – CALIFORNIA ONLY Requirements for
Emissions Campaigns Having
Customer Notification
The California Air Resources Board and the
Department of Motor Vehicles (DMV) require
emissions-related campaigns to be completed prior
to vehicle registration renewal. When campaign
work is done you must provide the owner with a
signed “Vehicle Emission Recall – Proof of
Correction” certificate (RC EMIS_CAL VW).
Certificates can be ordered at no cost can be
ordered at no cost online via the Compliance Label
Ordering portal at www.vwhub.com.
TIP
Ensure owners are aware of the importance
of retaining the completed certificate for their
records. It should be mailed to the California
DMV only upon request.
ALL WORK IS COMPLETE
The repair information in this document is intended for use only by skilled technicians who have the proper tools, equipment and training to correctly and safely maintain your vehicle. These
procedures are not intended to be attempted by “do-it-yourselfers,” and you should not assume this document applies to your vehicle, or that your vehicle has the condition described. To
determine whether this information applies, contact an authorized Volkswagen dealer. 2015 Volkswagen Group of America, Inc. and Volkswagen Canada. All Rights Reserved.
June 2015
23O6/D8 Page 15 of 15