Tech Ref 7-22-15

2016
Pre-Delivery Inspection
Technician Reference Document
Effective 7-22-2015-US
Version 1.5
Table
of Contents
A3/S3/A3
TDI
Technician Reference Document
Technician Reference Document Overview
The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with
the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more
efficient, and in doing so, this document has been created to be used as a reference for checklist items that
may have additional information. On the PDI Checklist, you find that certain items have been notated with an
asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference
Document.
Below you will find a list of each model, with the page numbers to their left. After navigating to the desired
page, you will notice each model page is formatted similarly to the PDI Checklists. After each section title is the
original checklist item, followed by any additional information specific to that model.
Table of Contents
3-4
A3/S3/A3 TDI
5-6
A3 Cabriolet
7-8
A3 e-tron Sportback
9-10
A4/S4/allroad
11-12
A5/S5/RS 5 Coupe
13-14
A5/S5/RS 5 Cabriolet
15-17
A6/S6/A6 TDI
18-20
A7/S7/A7 TDI
21-23
A8/A8 L/A8 W12/S8/A8 L TDI
24-25
Q3
26-27
Q5/Q5 hybrid/SQ5/Q5 TDI
28-29
TT/TTS Coupe
30-31
TT/TTS Roadster
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 2
A3/S3/A3 TDI
Technician Reference Document
Vehicle Preparation
Interior
• Deactivate vehicle transport mode
• Check operation of window, lock, and seat controls
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Control Module list –> 5F –>
Guided Functions –> 5F Adaption). Also referred to as CD
Ripping. Perform 3 button reset of the MMI to complete the
activation. Refer to the owners manual for model specific
button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
• Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Perform a battery test
Perform a battery test and attach the results to the repair
order
• Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Exterior
• Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
• Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
• Verify windows can be operated with the key
Verify windows roll down and sunroof opens when either the
key inserted in the door or by holding the unlock button on
the remote
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Inspect operation of all power outlets
Inspect operation of front outlet, USB 5v power jack, and
rear seat outlet
• Check panoramic sunroof operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Verify operation of speech dialogue system (if equipped)
Press the “Talk” button and verify several commands
• Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
• Set spare tire pressure
See separate “2016 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 3
A3/S3/A3 TDI
Technician Reference Document
Settings (continued)
On-Hoist Inspection (continued)
• Load Onboard Video Tutorials
• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
Media / Radio / SAT
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present, including
Audi brochure, AT&T brochure, customer SIM card, AT&T
Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the AT&T dealer demo SIM card to the vehicle and
make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)
• Verify engine performance and acceleration
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
• Turn on the wireless network
Ensure the wireless network is turned on (TEL > Settings >
Network connection (Wi-Fi) > select “Visible”)
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the LTE, 3G, or 2G symbol
On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
• Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 4
A3 Cabriolet
Technician Reference Document
Vehicle Preparation
Trunk Inspection (continued)
• Deactivate vehicle transport mode
• Set spare tire pressure 1.8T ONLY
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Control Module list –> 5F –>
Guided Functions –> 5F Adaption). Also referred to as CD
Ripping. Perform 3 button reset of the MMI to complete the
activation. Refer to the owners manual for model specific
button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
• Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Perform a battery test
Perform a battery test and attach the results to the repair
order
• Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Exterior
• Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
• Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
Effective 7-22-2015-US
Version 1.5
For the 1.8T A3 Cab, see separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet for proper
inflation. For the 2.0T A3 Cabriolet, verify the inflatable
spare tire and compressor are present
Interior
• Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
• Verify windows can be operated with the key
Verify windows roll down and sunroof opens when either the
key inserted in the door or by holding the unlock button on
the remote
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Inspect operation of all power outlets
Inspect operation of front outlet, USB 5v power jack, and
rear seat outlet
• Check panoramic sunroof operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
Model Year 2016 | Audi Pre-Delivery Reference Document | 5
A3 Cabriolet
Technician Reference Document
Settings (continued)
On-Hoist Inspection (continued)
• Load Onboard Video Tutorials
• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
Media / Radio / SAT
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present, including
Audi brochure, AT&T brochure, customer SIM card, AT&T
Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the AT&T dealer demo SIM card to the vehicle and
make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)
• Turn on the wireless network
Ensure the wireless network is turned on (TEL > Settings >
Network connection (Wi-Fi) > select “Visible”)
• Verify engine performance and acceleration
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Convertible Functionality (if equipped)
• Test operation of power folding top
Perform with engine running to conserve battery power
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the LTE, 3G, or 2G symbol
On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
• Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 6
A3 e-tron Sportback
Technician Reference Document
Vehicle Preparation
Interior
• Deactivate vehicle transport mode
• Check operation of window, lock, and seat controls
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Control Module list –> 5F –>
Guided Functions –> 5F Adaption). Also referred to as CD
Ripping. Perform 3 button reset of the MMI to complete the
activation. Refer to the owners manual for model specific
button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
• Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Perform a battery test
Perform a battery test and attach the results to the repair
order
• Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Exterior
• Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
• Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
• Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
• Verify windows can be operated with the key
Verify windows roll down and sunroof opens when either the
key inserted in the door or by holding the unlock button on
the remote
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Inspect operation of all power outlets
Inspect operation of front outlet, USB 5v power jack, and
rear seat outlet
• Check panoramic sunroof operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Verify operation of speech dialogue system (if equipped)
Press the “Talk” button and verify several commands
• Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 7
A3 e-tron Sportback
Technician Reference Document
Settings (continued)
On-Hoist Inspection (continued)
• Load Onboard Video Tutorials
• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
Media / Radio / SAT
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
Verify Audi connect Information Packet is present, including
Audi brochure, AT&T brochure, customer SIM card, AT&T
Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the AT&T dealer demo SIM card to the vehicle and
make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
• Verify engine performance and acceleration
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
• Turn on the wireless network
Ensure the wireless network is turned on (TEL > Settings >
Network connection (Wi-Fi) > select “Visible”)
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the LTE, 3G, or 2G symbol
Hybrid Technology
• Verify EV button is operating
Push the EV button at a speed below 80 mph and check for
lights on EV button and instrument cluster. Cycle through
the different EV modes: EV, Hybrid, Hold Battery, and Charge
Battery. These settings can be accessed through the MMI
via MENU > Car > Car systems > Charging & e-tron > e-tron
mode. EV mode may or may not activate based on current
operational criteria as described in the owner’s manual
• Verify charging while braking in recuperation range
On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
• Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
See power meter for details. Will only recuperate if battery is
not fully charged
• Check MMI and instrument cluster for proper operation
mode indication (only shows in MMI if equipped with NAV)
Verify green arrows while EV or electrical drive, orange
while combustion engine active, etc. Only shows in MMI if
equipped with NAV
• Verify front charge port is operational
Plug in charger and verify that it is operational and charges
the vehicle
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 8
A4/S4/allroad
Technician Reference Document
Vehicle Preparation
Trunk Inspection
• Deactivate vehicle transport mode
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. Perform 3 button reset of the MMI
to complete the activation. Refer to the owners manual for
model specific button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
• Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
• Check engine oil level
Check engine oil level using Special Tool T40178 on a flat and
level surface
Exterior
• Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
• Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
• Verify trunk/tailgate is operational
*tailgate for allroad only
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
• Set spare tire pressure
See separate “2016 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Interior
• Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
• Check panoramic sunroof operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Verify Voice Activation is operating
Press the “Talk” button and verify several commands
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 9
A4/S4/allroad
Technician Reference Document
Settings (continued)
On-Hoist Inspection
• Set “Music volume while parking” to 6 lines
• Inspect wheel bolts for proper torque
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera).
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
• Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
Use torque wrench to verify
• Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
• Verify engine performance and acceleration
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Media / Radio / SAT
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present including
Audi brochure, T-Mobile brochure, customer SIM card, T-Mobile Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
• Turn on the wireless network
Ensure the wireless network is turned on (TEL function
button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 10
A5/S5/RS 5 Coupe
Technician Reference Document
Vehicle Preparation
Trunk Inspection
• Deactivate vehicle transport mode
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. Perform 3 button reset of the MMI
to complete the activation. Refer to the owners manual for
model specific button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
• Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
• Check engine oil level
Check engine oil level using Special Tool T40178 on a flat and
level surface
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
• Set spare tire pressure
See separate “2016 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Interior
• Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Check panoramic sunroof operation
Verify open/close/vent/deflector at edge and sunshade
operation
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
Exterior
Settings
• Check all key buttons and features
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
• Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Verify Voice Activation is operating
Press the “Talk” button and verify several commands
• Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 11
A5/S5/RS 5 Coupe
Technician Reference Document
Settings (continued)
On-Hoist Inspection (continued)
• Set dealership location in navigation (if equipped)
• Install wheel bolt covers and center caps as supplied
Set dealership location for following back to dealership
during road test
• Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
Wheel bolt covers and center caps can be found in the PDI kit
• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
• Verify engine performance and acceleration
Media / Radio / SAT
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present including
Audi brochure, T-Mobile brochure, customer SIM card, T-Mobile Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
• Turn on the wireless network
Ensure the wireless network is turned on (TEL function
button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 12
A5/S5/RS 5 Cabriolet
Technician Reference Document
Vehicle Preparation
Trunk Inspection
• Deactivate vehicle transport mode
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. Perform 3 button reset of the MMI
to complete the activation. Refer to the owners manual for
model specific button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
• Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
• Check engine oil level
Check engine oil level using Special Tool T40178 on a flat and
level surface
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
• Set spare tire pressure
See separate “2016 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Interior
• Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify operation heated seats (if equipped)
Verify functionality of neck-level heating system (if
equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
Exterior
Settings
• Check all key buttons and features
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
• Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Verify Voice Activation is operating
Press the “Talk” button and verify several commands
• Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 13
A5/S5/RS 5 Cabriolet
Technician Reference Document
Settings (continued)
On-Hoist Inspection (continued)
• Set dealership location in navigation (if equipped)
• Install wheel bolt covers and center caps as supplied
Set dealership location for following back to dealership
during road test
• Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
Wheel bolt covers and center caps can be found in the PDI kit
• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
• Verify engine performance and acceleration
Media / Radio / SAT
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present including
Audi brochure, T-Mobile brochure, customer SIM card, T-Mobile Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
• Turn on the wireless network
Ensure the wireless network is turned on (TEL function
button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Convertible Functionality (if equipped)
• Test operation of power folding top
Perform with engine running to conserve battery power
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 14
A6/S6/A6 TDI
Technician Reference Document
Vehicle Preparation
Exterior (continued)
• Deactivate vehicle transport mode
• Test front washers (and headlight washers if equipped)
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
Headlights must be on to test functionality of the headlight
washers
• Deactivate air suspension loading mode
via Special Functions -> Service Work -> 34-Loading mode
activating/deactivating (if equipped) Warning! Car body may
lower!
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Control Module list –> 5F –>
Guided Functions –> 5F Adaption). Also referred to as CD
Ripping. Perform 3 button reset of the MMI to complete the
activation. Refer to the owners manual for model specific
button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc.
• Perform any open campaigns
Follow instructions listed in campaign documentation
Trunk Inspection
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
• Set spare tire pressure
See separate “2016 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Interior
• Verify operation heated/ventilated & massaging seats (if
equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
• Verify proper operation of climate control
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
• Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
Exterior
• Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
Effective 7-22-2015-US
Version 1.5
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Verify rear climate control operation (if equipped)
Verify heating and cooling functions and open all rear panel
vents
• Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, seat ventilation and massage (if equipped), heated
seats and child safety features
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify operation heated/ventilated & massaging seats (if
equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Verify rear climate control operation (if equipped)
Verify heating and cooling functions and open all rear panel
vents
Model Year 2016 | Audi Pre-Delivery Reference Document | 15
A6/S6/A6 TDI
Technician Reference Document
Interior (continued)
Audi connect (USA ONLY) (if equipped) (continued)
• Inspect operation of all power outlets
• Connect the dealer demo SIM card to verify system
connects to mobile network
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
• Check panoramic sunroof operation
Verify open/close/vent/deflector at edge and sunshade
operation
• Verify operation of all interior lights
Including ambient lighting (if equipped) Does this stay in?
Settings
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Verify Voice Activation is operating
Press the “Talk” button and verify several commands
• Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
• Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
Media / Radio / SAT
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Connect the AT&T dealer demo SIM card to the vehicle and
make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)
• Turn on the wireless network
Ensure the wireless network is turned on (TEL function
button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth (if equipped)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
• Install wheel bolt covers
Wheel bolt covers can be found in the PDI kit
• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
• Verify engine Start-Stop System functionality (if equipped)
Start-Stop-System info (if applicable): Verify the velum
sticker is on the start/stop button. Remove the start/stop
information card from the car kit and place it in the glove box
with the owner’s manuals. Additional supply can be ordered
via the Brand Store on AccessAudi
• Verify engine performance and acceleration
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present, including
Audi brochure, AT&T brochure, customer SIM card, AT&T
Terms & Conditions (T&C)(if applicable)
Effective 7-22-2015-US
Version 1.5
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
Model Year 2016 | Audi Pre-Delivery Reference Document | 16
A6/S6/A6 TDI
Technician Reference Document
Driving Performance (continued)
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify all vehicle Head-up Display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
• Verify operation of parking system (if equipped)
Verify operation of Audi parking system with rear view camera and top and/or corner view cameras (if equipped)
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 17
A7/S7/A7 TDI/RS 7
Technician Reference Document
Vehicle Preparation
Exterior (continued)
• Deactivate vehicle transport mode
• Check all doors for proper power closing (if equipped)
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
• Deactivate air suspension loading mode
via Special Functions -> Service Work -> 34-Loading mode
activating/deactivating (if equipped) Warning! Car body may
lower!
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Control Module list –> 5F –>
Guided Functions –> 5F Adaption). Also referred to as CD
Ripping. (Copying customer music from his device to the
hard drive of the vehicle). Perform 3 button reset of the MMI
to complete the activation. Refer to the owners manual for
model specific button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc.
• Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
• Check engine oil level
Check engine oil level via the MMI – fill oil to the max level
when the vehicle is at operating temperature
For vehicles equipped with the power door closing feature,
check all doors for proper closing
• Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
• Set spare tire pressure
See separate “2016 Normal Load Condition Tire Pressure
Table” posted on ServiceNet.
Interior
• Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, seat ventilation and massage (if equipped), heated
seats and child safety features
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify operation of all interior lights
Including ambient lighting (if equipped) Leave in?
• Verify operation heated/ventilated & massaging seats (if
equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Verify rear climate control operation (if equipped)
Exterior
• Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
Effective 7-22-2015-US
Version 1.5
Verify heating and cooling functions and open all rear panel
vents
• Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
Model Year 2016 | Audi Pre-Delivery Reference Document | 18
A7/S7/A7 TDI/RS 7
Technician Reference Document
Interior (continued
Audi connect (USA ONLY) (if equipped) (continued)
• Check panoramic sunroof operation
• Turn on the wireless network
Verify open/close/vent/ deflector at edge and sunshade operation
Settings
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
Ensure the wireless network is turned on (TEL function
button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth (if equipped)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
• Verify Voice Activation is operating
Press the “Talk” button and verify several commands
• Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
• Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
Media / Radio / SAT
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present, including
Audi brochure, AT&T brochure, customer SIM card, AT&T
Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the AT&T dealer demo SIM card to the vehicle and
make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)
Effective 7-22-2015-US
Version 1.5
On-Hoist Inspection
• Remove hoist access point trim covers (if equipped)
Prestige & S-Line only
• Inspect wheel bolts for proper torque
Use torque wrench to verify
• Install wheel bolt covers
Wheel bolt covers can be found in the PDI kit
• Remove hoist access point trim covers (if equipped)
Prestige & S-Line only
• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
• Verify engine Start-Stop System functionality (if equipped)
Start-Stop-System info (if applicable): Verify the velum
sticker is on the start/stop button. Remove the start/stop
information card from the car kit and place it in the glove box
with the owner’s manuals. Additional supply can be ordered
via the Brand Store on AccessAudi
• Verify engine performance and acceleration
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
Model Year 2016 | Audi Pre-Delivery Reference Document | 19
A7/S7/A7 TDI/RS 7
Technician Reference Document
Driving Performance (continued)
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify all vehicle Head-up Display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
• Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system plus with rear view
camera and top and/or corner view cameras (if equipped)
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 20
A8/A8 L/A8 W12/S8/A8 L TDI
Technician Reference Document
Vehicle Preparation
Exterior (continued)
• Deactivate vehicle transport mode
• Check all doors for proper power closing (if equipped)
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
• Deactivate air suspension loading mode
via Special Functions -> Service Work -> 34-Loading mode
activating/deactivating (if equipped) Warning! Car body may
lower!
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. Perform 3 button reset of the MMI
to complete the activation. Refer to the owners manual for
model specific button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc.
• Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
• Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Exterior
• Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
Effective 7-22-2015-US
Version 1.5
For vehicles equipped with the power door closing feature,
check all doors for proper closing
• Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
• Set spare tire pressure
See separate “2016 Normal Load Condition Tire Pressure
Table” posted on ServiceNet.
Interior
• Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, seat ventilation and massage (if equipped), heated
seats and child safety features
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify operation of all interior lights
Including ambient lighting (if equipped) Leave in?
• Verify operation heated/ventilated & massaging seats (if
equipped)
Check both front and rear. Massaging feature is in the front
seats only (if equipped) This is different on spreadsheet. No
massaging seats in text.
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Verify rear climate control operation (if equipped)
Verify heating and cooling functions and open all rear panel
vents
• Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
Model Year 2016 | Audi Pre-Delivery Reference Document | 21
A8/A8 L/A8 W12/S8/A8 L TDI
Technician Reference Document
Interior (continued
Audi connect (USA ONLY) (if equipped) (continued)
• Check panoramic sunroof operation
• Connect the dealer demo SIM card to verify system
connects to mobile network
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Verify Voice Activation is operating
Press the “Talk” button and verify several commands
• Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
Connect the AT&T dealer demo SIM card to the vehicle and
make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)
• Turn on the wireless network
Ensure the wireless network is turned on (TEL function
button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth (if equipped)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
• Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
Media / Radio / SAT
On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
• Install wheel bolt covers
Wheel bolt covers can be found in the PDI kit
• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
• Verify operation of Rear Seat Entertainment (if equipped)
Rear Seat Entertainment/Rear MMI: Verify operation. Verify
the wireless headphones are present and pair them to the
RSE system (refer to RSE manual). When pairing the headphones, press and hold the on/off button for 4–5 seconds
until the light starts flashing quickly. Also verify the DVD
units operate
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Driving Performance
• Verify engine Start-Stop System functionality (if equipped)
Start-Stop-System info (if applicable): Verify the velum
sticker is on the start/stop button. Remove the start/stop
information card from the car kit and place it in the glove box
with the owner’s manuals. Additional supply can be ordered
via the Brand Store on AccessAudi
• Verify engine performance and acceleration
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present, including
Audi brochure, AT&T brochure, customer SIM card, AT&T
Terms & Conditions (T&C)(if applicable)
Effective 7-22-2015-US
Version 1.5
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
Model Year 2016 | Audi Pre-Delivery Reference Document | 22
A8/A8 L/A8 W12/S8/A8 L TDI
Technician Reference Document
Driving Performance (continued)
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify all vehicle Head-up Display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
• Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system plus with rear view
camera and top and/or corner view cameras (if equipped)
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 23
Q3
Technician Reference Document
Vehicle Preparation
Trunk Inspection
• Deactivate vehicle transport mode
• Verify power rear tailgate is operational and set default
opening height (if equipped)
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. Perform 3 button reset of the MMI
to complete the activation. Refer to the owners manual for
model specific button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
• Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Check engine oil level
Check engine oil level via the MMI – fill oil to the max level
when the vehicle is at operating temperature
• Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
• Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
If equipped with power rear tailgate, adjust the opening
height to 75 inches (190 cm) from the ground to the close
button in the rear lid. Press and hold the close button in the
rear lid for at least four seconds to program the opening
height
• Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit to the right of the
spare tire
• Set spare tire pressure
See separate “2016 Normal Load Condition Tire Pressure
Table” posted on ServiceNet.
Interior
• Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Inspect operation of all power outlets
Inspect operation of outlet in front of center console and
behind center console
• Check panoramic sunroof operation
Verify open/close/vent/deflector at edge and sunshade
operation
Exterior
Settings
• Check all key buttons and features
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
• Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Effective 7-22-2015-US
Version 1.5
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Verify Voice Activation is operating
Press the “Talk” button and verify several commands
Model Year 2016 | Audi Pre-Delivery Reference Document | 24
Q3
Technician Reference Document
Settings (continued)
On-Hoist Inspection (continued)
• Set “Music volume while parking” to 6 lines
• Set and store tire pressures for either sold vehicle OR
stock inventory vehicle (See separate “2016 Normal Load
Condition Tire Pressure Table” posted on ServiceNet)
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Media / Radio / SAT
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Driving Performance
• Verify engine performance and acceleration
Listen for abnormal noise/vibrations
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present including
Audi brochure, T-Mobile brochure, customer SIM card,
T-Mobile Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
• Turn on the wireless network
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Ensure the wireless network is turned on (TEL function
button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
• Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 25
Q5/Q5 hybrid/SQ5/Q5 TDI
Technician Reference Document
Vehicle Preparation
Trunk Inspection
• Deactivate vehicle transport mode
• Verify power rear tailgate is operational and set default
opening height (if equipped)
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. Perform 3 button reset of the MMI
to complete the activation. Refer to the owners manual for
model specific button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
• Perform any open campaigns
Follow instructions listed in campaign documentation
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Check engine oil level
Check engine oil level via the MMI – fill oil to the max level
when the vehicle is at operating temperature
• Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
• Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
Exterior
• Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
• Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Effective 7-22-2015-US
Version 1.5
If equipped with power rear tailgate, adjust the opening
height to 75 inches (190 cm) from the ground to the close
button in the rear lid. Press and hold the close button in the
rear lid for at least four seconds to program the opening
height
• Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit to the right of the
spare tire
• Install the hitch cover cap (if equipped)
The cap is located in the cargo area
Interior
• Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify operation heated/ventilated seats (if equipped)
Check both front and rear (if equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
• Verify rear climate control operation (if equipped)
Verify heating and cooling functions and open all rear panel
vents
• Inspect operation of all power outlets
Inspect operation of outlet in front of center console and
behind center console
• Check panoramic sunroof operation
Verify open/close/vent/deflector at edge and sunshade operation (front and rear).
Settings
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
Model Year 2016 | Audi Pre-Delivery Reference Document | 26
Q5/Q5 hybrid/SQ5/Q5 TDI
Technician Reference Document
Settings (continued)
Audi connect (USA ONLY) (if equipped) (continued)
• Verify and set language and Measurement Units
• Enable Google Earth
This can be changed in the Setup/Settings menu
• Verify Voice Activation is operating
Press the “Talk” button and verify several commands
• Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
• Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man.
function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
Media / Radio / SAT
• Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present including
Audi brochure, T-Mobile brochure, customer SIM card,
T-Mobile Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
• Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
• Set and store tire pressures for either sold vehicle OR
stock inventory vehicle (See separate “2016 Normal Load
Condition Tire Pressure Table” posted on ServiceNet)
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
• Verify engine performance and acceleration
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
• Turn on the wireless network
Ensure the wireless network is turned on (TEL function
button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 27
TT/TTS Coupe
Technician Reference Document
Vehicle Preparation
Interior
• Deactivate vehicle transport mode
• Check operation of window, lock, and seat controls
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Control Module list –> 5F –>
Guided Functions –> 5F Adaption). Also referred to as CD
Ripping. Perform 3 button reset of the MMI to complete the
activation. Refer to the owners manual for model specific
button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
• Perform any open campaigns
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
• Inspect operation of all power outlets
Inspect operation of outlet under armrest, and rear outlet
Follow instructions listed in campaign documentation
Settings
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Perform a battery test
Perform a battery test and attach the results to the repair
order
• Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Verify operation of speech dialogue system (if equipped)
Press the “Talk” button and verify several commands
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
Exterior
• Check all key buttons and features
Check key functionality including seat and steering wheel
position memory; verify vehicle starts and runs with all keys
and the start/stop button; verify all doors and trunk manually and remotely lock/unlock with all keys, including all door
handle sensors with the Advanced Key (if equipped)
Trunk Inspection
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
• Set spare tire pressure
See separate “2016 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Effective 7-22-2015-US
Version 1.5
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present, including
Audi brochure, AT&T brochure, customer SIM card, AT&T
Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the AT&T dealer demo SIM card to the vehicle and
make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)
• Turn on the wireless network
Ensure the wireless network is turned on (TEL > Settings >
Network connection (Wi-Fi) > select “Visible”)
Model Year 2016 | Audi Pre-Delivery Reference Document | 28
TT/TTS Coupe
Technician Reference Document
Audi connect (USA ONLY) (if equipped) (continued)
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the LTE, 3G, or 2G symbol
On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
• Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
• Verify engine performance and acceleration
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
• Verify operation of Audi parking system
Verify operation of Audi parking system sensors; Rear
sensors standard, front sensors and rear view camera (if
equipped)
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 29
TT/TTS Roadster
Technician Reference Document
Vehicle Preparation
Interior
• Deactivate vehicle transport mode
• Check operation of window, lock, and seat controls
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
• Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Control Module list –> 5F –>
Guided Functions –> 5F Adaption). Also referred to as CD
Ripping. Perform 3 button reset of the MMI to complete the
activation. Refer to the owners manual for model specific
button sequence
• Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
• Perform any open campaigns
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
• Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating
• Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
• Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
• Inspect operation of all power outlets
Inspect operation of outlet under armrest, and rear outlet
Follow instructions listed in campaign documentation
Settings
Under the Hood Inspection
• Check battery clamps for proper torque
Re-torque if required
• Perform a battery test
Perform a battery test and attach the results to the repair
order
• Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
• Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
• Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
• Verify operation of speech dialogue system (if equipped)
Press the “Talk” button and verify several commands
• Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
Exterior
• Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
Trunk Inspection
• Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
• Set spare tire pressure
See separate “2016 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Effective 7-22-2015-US
Version 1.5
Audi connect (USA ONLY) (if equipped)
• Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present, including
Audi brochure, AT&T brochure, customer SIM card, AT&T
Terms & Conditions (T&C)(if applicable)
• Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the AT&T dealer demo SIM card to the vehicle and
make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)
• Turn on the wireless network
Ensure the wireless network is turned on (TEL function
button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
Model Year 2016 | Audi Pre-Delivery Reference Document | 30
TT/TTS Roadster
Technician Reference Document
Audi connect (USA ONLY) (if equipped) (continued)
• Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
• Enable Google Earth
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the LTE, 3G, or 2G symbol
On-Hoist Inspection
• Inspect wheel bolts for proper torque
Use torque wrench to verify
• Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
• Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2016 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance
• Verify engine performance and acceleration
Listen for abnormal noise/vibrations
• Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
• Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driving Assistance
• Verify operation of parking system
Verify operation of Audi parking system sensors; Rear sensors standard, front sensors and rear view camera if equipped
Convertible Functionality (if equipped)
• Test operation of power folding top
Perform with engine running to conserve battery power
Effective 7-22-2015-US
Version 1.5
Model Year 2016 | Audi Pre-Delivery Reference Document | 31