T-SB-0001-18_Rev
Service Bulletin Details
Public Details for: T-SB-0001-18_Rev
Tsb: revision notice february 02, 2018 rev1: ? Applicability has been updated to include 2018 model year sienna vehicles. ? The entire bulletin has been updated. Any previous printed versions of this bulletin should be discarded. When compl
Models from 2018
2018 TOYOTA HIGHLANDER |
2018 TOYOTA SIENNA |
Models from 2017
2017 TOYOTA HIGHLANDER |
2017 TOYOTA SIENNA |
T-SB-0001-18 Rev1 January 8, 2018 Transaxle Assembly and ECM (PCM) Software Confirmation Service Category Engine/Hybrid System Section Engine Control Market USA Applicability YEAR(S) MODEL(S) 2017 - 2018 Highlander, Sienna ADDITIONAL INFORMATION REVISION NOTICE February 02, 2018 Rev1: Applicability has been updated to include 2018 model year Sienna vehicles. The entire bulletin has been updated. Any previous printed versions of this bulletin should be discarded. Introduction When completing a transaxle assembly replacement, Engine Control Module (ECM) (SAE term: Powertrain Control Module [PCM]) replacement, or ECM (PCM) reprogram, ensure the correct ECM (PCM) software is matched with the transaxle assembly hardware. Some 2017 – 2018 model year Highlander and Sienna vehicles require different ECM (PCM) software based on the transaxle assembly hardware installed in the vehicle. NOTICE Mismatched transaxle assembly hardware and ECM (PCM) software combinations may result in a harsh shift or shift flare. If this occurs after the original repair, additional ECM (PCM) replacement and reprogramming will be required. This additional ECM (PCM) replacement and/or reprogramming is NOT covered under warranty. Use the information in this Service Bulletin to confirm that the correct ECM (PCM) hardware and software are used based on the transaxle assembly part number and serial number. © 2018 Toyota Motor Sales, USA Page 1 of 11 T-SB-0001-18 Rev1 January 8, 2018 Page 2 of 11 Transaxle Assembly and ECM (PCM) Software Confirmation Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 369011# Z Time Add-on to Transaxle Replacement OP Code 0.3 30500-####0 TBD* TBD* * Based on replacement phenomenon. NOTE For transaxle replacement: Claim should be submitted as a normal replacement of the transaxle. If the ECM (PCM) software needs to be updated when replacing the transaxle, add 0.3 hours of “Z time” to the transaxle replacement OP code. For ECM (PCM) reprogramming or replacement: This Service Bulletin is used for ECM (PCM) and software selection; however, this does NOT incur additional warranty cost. Parts Information PART NUMBER PREVIOUS PART NAME QTY Authorized Modifications Labels 1 NEW 00451-00001-LB L NOTE Authorized Modifications Labels may be ordered in packages of 25 from the Materials Distribution Center (MDC) through Dealer Daily – Parts – Dealer Support Materials Orders. Required Tools & Equipment REQUIRED EQUIPMENT SUPPLIER Techstream 2.0* Techstream Lite PART NUMBER QTY TS2UNIT ADE Techstream Lite (Green Cable) TSLITEPDLR01 TSLP2DLR01 * Essential SST. NOTE Only ONE of the Techstream units listed above is required. Software version 12.20.024 or later is required. Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at 1-800-368-6787. Use Techstream or an approved J2534 interface to perform flash reprogramming updates. Visit techinfo.toyota.com for more information regarding J2534 reprogramming. © 2018 Toyota Motor Sales, USA 1 T-SB-0001-18 Rev1 January 8, 2018 Page 3 of 11 Transaxle Assembly and ECM (PCM) Software Confirmation Required Tools & Equipment (continued) SPECIAL SERVICE TOOLS (SST) PART NUMBER QTY GR8 Battery Diagnostic Station* 00002-MCGR8 1 * Essential SST. NOTE Additional SSTs may be ordered by calling 1-800-933-8335. Production Change Confirmation Procedure For transaxle assembly replacement, go to Option 1 and use the part number on the transaxle assembly AND Table 1 to confirm if the transaxle that was just installed is BEFORE or AFTER the production change. This information will allow you to confirm, using the Calibration Information table on pages 7 – 8, if the vehicle has the correct, matching software for that transaxle. If NOT replacing the transaxle and you would like to confirm that the software matches the transaxle, go to Option 2 and use the serial number on the transaxle assembly to determine if the transaxle was built BEFORE or AFTER the production change. This information will allow you to confirm, using the Calibration Information table on pages 7 – 8, if the vehicle has the correct, matching software for that transaxle. Option 1: Confirmation by Part Number 1. Determine if the vehicle has a transaxle assembly produced BEFORE or AFTER the production change using the table below. Table 1. JUDGEMENT Before After PART NUMBER PART NAME 30510-####0-84 Reman ATM 30500-####0 Transaxle, Assy 30510-####1-84 Reman ATM 30500-####1 Transaxle, Assy 2. Using the judgement from Table 1, refer to the Engine Control Computer (ECM/PCM) Replacement Information and Calibration Information sections. NOTE If unable to determine the part number, continue to Option 2: Confirmation by Production Change Effective Serial Number. © 2018 Toyota Motor Sales, USA T-SB-0001-18 Rev1 January 8, 2018 Page 4 of 11 Transaxle Assembly and ECM (PCM) Software Confirmation Production Change Confirmation Procedure (continued) Option 2: Confirmation by Production Change Effective Serial Number 1. Locate the transaxle serial number, found on the sticker located on the transaxle assembly side cover or on the engraved location as shown. Serial number decoders are also provided below. Figure 1. Serial Number Sticker and Engraved Serial Number Location 1 2 1 Serial Num ber Sticker 2 Engraved Serial Number Location Figure 2. AW Plant Serial Number Decoder Figure 3. Kinuura Plant Serial Number Decoder © 2018 Toyota Motor Sales, USA T-SB-0001-18 Rev1 January 8, 2018 Page 5 of 11 Transaxle Assembly and ECM (PCM) Software Confirmation Production Change Confirmation Procedure (continued) Option 2: Confirmation by Production Change Effective Serial Number (continued) 2. Use the table below to determine if the vehicle has a transaxle assembly produced BEFORE or AFTER the production change. Table 2. PLANT PRODUCTION CHANGE EFFECTIVE SERIAL NUMBER AW 7A617M22012 Kinuura UA03L217C21Y206 3. Using the information from Table 2, refer to the Engine Control Computer (ECM/PCM) Replacement Information and Calibration Information sections. Engine Control Computer (ECM/PCM) Replacement Information Based on the judgement of the transaxle serial number, use the table below to ensure that the correct ECM (PCM) is ordered for ANY replacements being performed. JUDGEMENT YEAR MODEL DRIVETRAIN START & STOP PREVIOUS NEW Y 89661-0E851 89661-0E850-B 89661-0E852 N 89661-0E861 89661-0E860-B 89661-0E862 Y 89661-0E831 89661-0E830-B 89661-0E832 89661-0E841 89661-0E840-B 89661-0E842 89661-08164 89661-08163 89661-08160-B 89661-08165 4WD 89661-08444 89661-08443 89661-08440-B 89661-08445 2WD 89661-08400 4WD 89661-08460 2WD 2017 – 2018 Highlander 4WD Before 2WD 2017 N Sienna 2018 PART NUMBER © 2018 Toyota Motor Sales, USA – T-SB-0001-18 Rev1 January 8, 2018 Page 6 of 11 Transaxle Assembly and ECM (PCM) Software Confirmation Engine Control Computer (ECM/PCM) Replacement Information (continued) JUDGEMENT YEAR MODEL DRIVETRAIN START & STOP PREVIOUS NEW 89661-0E852 89661-0E851 89661-0E850-B 89661-0ED80 89661-0E842 89661-0E841 89661-0E840-B 89661-0ED70 89661-08165 89661-08164 89661-08163 89661-08160-B 89661-08530 4WD 89661-08445 89661-08444 89661-08443 89661-08440-B 89661-08540 2WD 89661-08400 89661-08580 4WD 89661-08460 89661-08590 Y 2017 – 2018 Highlander 2WD After 2017 N Sienna PART NUMBER 2018 © 2018 Toyota Motor Sales, USA T-SB-0001-18 Rev1 January 8, 2018 Page 7 of 11 Transaxle Assembly and ECM (PCM) Software Confirmation Calibration Information Based on the judgement of the transaxle serial number, use the table below to ensure the correct calibration file is used for ANY ECM (PCM) reprogramming procedures being performed. JUDGEMENT YEAR MODEL DRIVETRAIN START & STOP Y 2WD N 2017 – 2018 Highlander Y 4WD Before ECU TYPE PREVIOUS NEW Main 896630E45100 896630E45000 896630E45200 Sub 896650E11000 896650E11100 Main 896630E46100 896630E46000 896630E46200 Sub 896650E12000 896650E12100 Main 896630E43100 896630E43000 896630E43200 Sub 896650E09000 896650E09100 Main 896630E44100 896630E44000 896630E44200 Sub 896650E10000 896650E10100 Main 896630828400 896630828300 896630828000 896630828500 Sub 896650807100 896650807000 896650807200 Main 896630836400 896630836300 896630836000 896630836500 Sub 896650808100 896650808000 896650808200 Main 896630832000 Sub 896650811000 Main 896630838000 Sub 896650812000 2WD 2017 N Sienna 4WD 2WD 2018 4WD CALIBRATION ID © 2018 Toyota Motor Sales, USA – T-SB-0001-18 Rev1 January 8, 2018 Page 8 of 11 Transaxle Assembly and ECM (PCM) Software Confirmation Calibration Information (continued) JUDGEMENT YEAR MODEL DRIVETRAIN START & STOP ECU TYPE PREVIOUS NEW Main 896630E45200 896630E45100 896630E45000 896630E85000 Sub 896650E11100 896650E11000 896650E43000 Main 896630E46200 896630E46100 896630E46000 896630E86000 Sub 896650E12100 896650E12000 896650E44000 Main 896630E43200 896630E43100 896630E43000 896630E83000 Sub 896650E09100 896650E09000 896650E41000 Main 896630E44200 896630E44100 896630E44000 896630E84000 Sub 896650E10100 896650E10000 896650E42000 Main 896630828500 896630828400 896630828300 896630828000 896630846000 Sub 896650807200 896650807100 896650807000 896650819000 Main 896630836500 896630836400 896630836300 896630836000 896630847000 Sub 896650808200 896650808100 896650808000 896650820000 Main 896630832000 896630851000 Sub 896650811000 896650823000 Main 896630838000 896630852000 Sub 896650812000 896650824000 Y 2WD N 2017 – 2018 Highlander Y 4WD After 2WD N 2017 Sienna 4WD 2WD 2018 4WD CALIBRATION ID © 2018 Toyota Motor Sales, USA T-SB-0001-18 Rev1 January 8, 2018 Page 9 of 11 Transaxle Assembly and ECM (PCM) Software Confirmation Repair Procedure 1. Does the ECM (PCM) need to be reprogrammed? YES — Continue to step 2. NO — This bulletin does NOT apply. Continue diagnosis using the applicable Repair Manual. 2. Check for the Authorized Modifications Label affixed to the vehicle in the applicable locations shown below. Is the calibration ID listed the latest ECM (PCM) calibration? YES — This bulletin does NOT apply. Continue diagnosis using the applicable Repair Manual. NO — Continue to step 2. Figure 4. Location of Authorized Modifications Label for 2017 – 2018 Highlander 1 2 4 3 5 1 Replacement ECM (PCM) Part Number (e.g., 89661-0E832) 4 Date Com pleted 2 New Calibration ID (e.g., 896630E43200) 5 This SB Num ber 3 Dealer Code © 2018 Toyota Motor Sales, USA T-SB-0001-18 Rev1 January 8, 2018 Page 10 of 11 Transaxle Assembly and ECM (PCM) Software Confirmation Repair Procedure (continued) Figure 5. Location of Authorized Modifications Label for 2017 – 2018 Sienna 1 2 3 4 5 1 Replacement ECM (PCM) Part Number (e.g., 89661-08165) 4 Date Com pleted 2 New Calibration ID (e.g., 896630836500) 5 This SB Num ber 3 Dealer Code 3. Flash reprogram the ECM (PCM). NOTE The GR8 Battery Diagnostic Station MUST be used in Power Supply Mode to maintain battery voltage at 13.5V while flash reprogramming the vehicle. For details on how to use the GR8 Battery Diagnostic Station, refer to the “GR8 Instruction Manual” located at TIS – Diagnostics – Tools & Equipment – Battery Diagnostics. Follow the procedures outlined in Service Bulletin No. T-SB-0134-16 “Techstream ECU Flash Reprogramming Procedure,” and flash the ECM (PCM) with the NEW calibration file update. © 2018 Toyota Motor Sales, USA T-SB-0001-18 Rev1 January 8, 2018 Page 11 of 11 Transaxle Assembly and ECM (PCM) Software Confirmation Repair Procedure (continued) 4. Prepare and install the Authorized Modifications Label. A. Using a permanent marker, enter the following information on the label: ECM (PCM) part number [Refer to the Parts Information section for the NEW PART NUMBER] Calibration ID [Refer to the Calibration Information section for the NEW CALIBRATION ID] Dealer Code Repair Date Change Authority [This bulletin number] B. Affix the Authorized Modifications Label to the vehicle at the location shown in Figures 4 and 5. The Authorized Modifications Label is available through the MDC, P/N 00451-00001-LBL. 5. Test drive the vehicle to confirm proper vehicle operation. © 2018 Toyota Motor Sales, USA