L-SB-0009-18

L-SB-0009-18
February 26, 2018
Blind Spot Monitor DTC C1AB2/C1AB3
Service
Category
Audio/Visual/Telematics
Section
Park Assist/Monitoring
Market USA
Applicability
YEAR(S)
MODEL(S)
2015 - 2016
NX200T, NX300H
ADDITIONAL INFORMATION
Introduction
Some 2015 – 2016 model year NX 200t and NX 300h vehicles equipped with blind spot monitor
may exhibit a blind spot monitor warning message with Diagnostic Trouble Code (DTC) C1AB2
(Short to Ground in Outer Mirror Indicator [Master]) or C1AB3 (Short to Ground in Outer Mirror
Indicator [Slave]) present. Follow the Repair Procedure in this bulletin to address this condition.
Production Change Information
This bulletin applies to vehicles produced BEFORE the Production Change Effective VINs
shown below.
 ALL 2015 model year vehicles.

2016 model year vehicles produced BEFORE the Production Change Effective VINs
shown below.
MODEL
DRIVETRAIN
PRODUCTION CHANGE EFFECTIVE VIN
2WD
JTJYARBZ#G2042100
AWD
JTJBARBZ#G2084425
2WD
JTJYWRBZ#G2012718
AWD
JTJBJRBZ#G2045529
NX 200t
NX 300h
© 2018 Lexus, a division of Toyota Motor Sales, USA
Page 1 of 4
L-SB-0009-18
February 26, 2018
Page 2 of 4
Blind Spot Monitor DTC C1AB2/C1AB3
Warranty Information
OP CODE
DESCRIPTION
TIME
EL9051
Replace Blind Spot Monitor Sensor (One Side)
2.5
EL9051A
Other Side
0.5
OFP
T1
T2
88162-0W170
8A
74
APPLICABLE WARRANTY
 This repair is covered under the Lexus Basic Warranty. This warranty is in effect for 48
months or 50,000 miles, whichever occurs first, from the vehicle’s in-service date.
 Warranty application is limited to occurrence of the specified condition described in
this bulletin.
Parts Information
PART NUMBER
PREVIOUS
NEW
88162-0W170
88162-78010
PART NAME
QTY
Sensor, Blind Spot Monitor
1
Required Tools & Equipment
SPECIAL SERVICE TOOLS (SST)
PART NUMBER
QTY
Laser Radar Adjusting Reflector*
09870-60000
1
Reflector C*
09870-60040
1
* Essential SST.
NOTE
Additional SSTs may be ordered by calling 1-800-933-8335.
REQUIRED EQUIPMENT
SUPPLIER
Techstream 2.0*
Techstream Lite
PART NUMBER
QTY
TS2UNIT
ADE
Techstream Lite (Green Cable)
TSLITEPDLR01
TSLP2DLR01
* Essential SST.
NOTE
 Only ONE of the Techstream units listed above is required.
 Software version 13.00.022 or later is required.
 Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE)
at 1-800-368-6787.
© 2018 Lexus, a division of Toyota Motor Sales, USA
1
L-SB-0009-18
February 26, 2018
Page 3 of 4
Blind Spot Monitor DTC C1AB2/C1AB3
Repair Procedure
1. Using Techstream, check for the following stored DTCs:
C1AB2 – Short to Ground in Outer Mirror Indicator (Master)
C1AB3 – Short to Ground in Outer Mirror Indicator (Slave)
Is either DTC present?
 YES — Continue to step 2.

NO — This bulletin does NOT apply. Continue diagnosis using the applicable Repair Manual.
NOTE
If blind spot monitor DTCs C1AC1 (Master Module Horizontal Axis Misalignment) or
C1AC2 (Slave Module Horizontal Axis Misalignment) are present, they MUST be corrected BEFORE
proceeding with this Service Bulletin.
2. Replace the blind spot monitor sensor
indicated by the DTC.
A. Remove the blind spot monitor sensor.
Refer to TIS, applicable model and model
year Repair Manual:
 2015 – 2016 NX 200t:
Audio/Visual/Telematics – Park
Assist/Monitoring – “Park Assist /
Monitoring: Blind Spot Monitor
Sensor: Removal”
 2015 – 2016 NX 300h:
Audio/Visual/Telematics – Park
Assist/Monitoring – “Park Assist /
Monitoring: Blind Spot Monitor
Sensor: Removal”
Figure 1. Sensor Location
2
1
1
Blind Spot Monitor Sensor Master
2
Blind Spot Monitor Sensor Slave
B. Install the NEW blind spot monitor sensor.
Refer to TIS, applicable model and model year Repair Manual:
 2015 – 2016 NX 200t:
Audio/Visual/Telematics – Park Assist/Monitoring – “Park Assist / Monitoring: Blind Spot
Monitor Sensor: Installation”
 2015 – 2016 NX 300h:
Audio/Visual/Telematics – Park Assist/Monitoring – “Park Assist / Monitoring: Blind Spot
Monitor Sensor: Installation”
© 2018 Lexus, a division of Toyota Motor Sales, USA
L-SB-0009-18
February 26, 2018
Page 4 of 4
Blind Spot Monitor DTC C1AB2/C1AB3
Repair Procedure (continued)
3. Perform the Blind Spot Monitor Beam Axis Inspection.
Refer to TIS, applicable model and model year Repair Manual:
 2015 – 2016 NX 200t:
Audio/Visual/Telematics – Park Assist/Monitoring – “Park Assist / Monitoring: Blind Spot
Monitor System: Operation Check”

2015 – 2016 NX 300h:
Audio/Visual/Telematics – Park Assist/Monitoring – “Park Assist / Monitoring: Blind Spot
Monitor System: Operation Check”
NOTE
The Blind Spot Monitor Beam Axis Inspection may have been included as part of sensor installation
and only needs to be performed once.
4. Perform the Blind Spot Monitor Beam Axis Confirmation.
Refer to TIS, applicable model and model year Repair Manual:
 2015 – 2016 NX 200t:
Audio/Visual/Telematics – Park Assist/Monitoring – “Park Assist / Monitoring: Blind Spot
Monitor System: Operation Check”

2015 – 2016 NX 300h:
Audio/Visual/Telematics – Park Assist/Monitoring – “Park Assist / Monitoring: Blind Spot
Monitor System: Operation Check”
NOTE
The Blind Spot Monitor Beam Axis Confirmation may have been included as part of sensor installation
and only needs to be performed once.
5. Clear the DTCs using Techstream.
6. Verify proper operation of the blind spot monitor system.
© 2018 Lexus, a division of Toyota Motor Sales, USA