S-SB-0005-14

April 14, 2014
S-SB-0005-14
Floor Mat Installation During PDS
Service
Category
General
Section
Pre-Delivery Service
Market
USA
Applicability
YEAR(S)
MODEL(S)
2015
FR-S, iQ, tC, xB
ADDITIONAL INFORMATION
Introduction
2015 model year vehicles are equipped with driver’s side floor mat retaining clips to secure the floor
mat in the correct position. In addition, some models may utilize retaining clips for passenger side
floor mats as well. Follow the appropriate installation procedure to attach the driver’s side and
passenger’s side (if applicable) floor mat to the vehicle carpet using the floor mat retaining clips
during Pre-Delivery Service (PDS).
CAUTION
• ALWAYS verify the floor mat to ensure it is designed specifically for the model and model
year it is being installed in.
• ONLY use floor mats that can be retained using the retaining clips. All OEM Scion floor mats
are specifically designed to fit correctly and be retained using the retaining clips.
• Make sure the floor mat is properly placed on the vehicle carpet and secured with the retaining
clips. If the driver side floor mat is NOT properly placed and secured, it could slip and interfere
with the movement of the pedals during driving and may cause an accident.
• Verify the operation of the accelerator, brake, and clutch (if equipped) pedals and clearance
to the mat.
• NEVER install more than one floor mat at a time in the driver’s seating position.
• If applicable, any secondary set of floor mats (based upon customer preference, such as the
all weather floor mats or other floor mats) MUST be placed in the trunk with all the packaging
material intact. Do NOT install the secondary mat on top of the primary floor mat already
installed in the driver’s seating position.
Warranty Information
OP CODE
DESCRIPTION
TIME
OFP
T1
T2
N/A
Not Applicable to Warranty
–
–
–
–
© 2014 Toyota Motor Sales, USA
Page 1 of 12
April 14, 2014
S-SB-0005-14
Page 2 of 12
Floor Mat Installation During PDS
Installation Procedure: Hook Style
1. Verify that the driver and passenger side (if applicable) floor mats are for the correct model
and model year they are being installed in.
2. Attach the driver and passenger side (if applicable) floor mats to the vehicle carpet using the
retaining clips. Secure the mat by inserting the retaining clips through the grommet holes.
Figure 1.
0000000000
0000000000
0000000000
3
0000
000
0000000000
0000
000
0000000000
0000000000
0000
0000000000
0000000000
1
2
0000000000
0000
0000000000
0000000000
0000
1
Retaining Clips
2
Grommets
3
© 2014 Toyota Motor Sales, USA
Correct Installation
April 14, 2014
S-SB-0005-14
Page 3 of 12
Floor Mat Installation During PDS
Installation Procedure: Hook Style (Continued)
3. Verify proper installation.
NOTE
If applicable, DO NOT remove the beige “Caution” tag from the floor mat. This should only be
removed by the customer.
Figure 2.
© 2014 Toyota Motor Sales, USA
April 14, 2014
S-SB-0005-14
Page 4 of 12
Floor Mat Installation During PDS
Installation Procedure: Hook Style with Locking Clip
1. Verify that the driver and passenger side (if applicable) floor mats are for the correct model
and model year they are being installed in.
2. Attach the retention clip to the floor by inserting the retention clip claws into the floor eyelet.
Figure 3.
5
B
B
1
4
A
A
B
3
2
1
Retention Clip
5
Cross-sectional Diagram
2
Front of Vehicle
A
Retention Clip Claw
3
Retention Clip Eyelet on Vehicle Floor
B
Locking Clip
4
Seat
© 2014 Toyota Motor Sales, USA
April 14, 2014
S-SB-0005-14
Page 5 of 12
Floor Mat Installation During PDS
Installation Procedure: Hook Style with Locking Clip (Continued)
3. To lock the retention clip in place, insert the
locking clip of the retention clip into the
designated hole.
Figure 4..
1
1
4. Align the floor mat holes with the retention clip
hooks and place the floor mat holes onto the
retention clip hooks.
Locking Clip
Figure 5..
1
2
3
1
Retention Clip Eyelet on Floor Mat
2
Retention Clip
3
Front
© 2014 Toyota Motor Sales, USA
April 14, 2014
S-SB-0005-14
Page 6 of 12
Floor Mat Installation During PDS
Installation Procedure: Hook Style with Locking Clip (Continued)
5. Verify proper installation.
NOTE
If applicable, DO NOT remove the beige “Caution” tag from the floor mat. This should only be
removed by the customer.
Figure 6.
© 2014 Toyota Motor Sales, USA
April 14, 2014
S-SB-0005-14
Page 7 of 12
Floor Mat Installation During PDS
Installation Procedure: Knob Style with Locking Clip
1. Verify that the driver and passenger side (if applicable) floor mats are for the correct model
and model year they are being installed in.
2. Attach the retention clip to the floor by inserting
the retention clip claws into the floor eyelet.
Figure 7.
.
1
B
3
A
4
2
B
A
1
Retention Clip
2
Retention Clip Eyelet on Vehicle Floor
3
Seat
4
Front of Vehicle
A
Retention Clip Claws
B
Locking Clip
© 2014 Toyota Motor Sales, USA
April 14, 2014
S-SB-0005-14
Page 8 of 12
Floor Mat Installation During PDS
Installation Procedure: Knob Style with Locking Clip (Continued)
3. To lock the clip in place, insert the locking clip of
the retention clip into the designated hole.
Figure 8.
.
1
1
4. Align the floor mat holes with the retention clip
knobs and place the floor mat holes onto the
retention clip knobs.
Locking Clip
Figure 9.
.
1
2
3
1
Retention Clip Eyelet on Floor Mat
2
Retention Clip
3
Front of Vehicle
© 2014 Toyota Motor Sales, USA
April 14, 2014
S-SB-0005-14
Page 9 of 12
Floor Mat Installation During PDS
Installation Procedure: Knob Style with Locking Clip (Continued)
5. Turn the retention clip knobs a quarter of a turn to
lock in place and verify the “triangle” marks on the
retention clip knob and floor mat are aligned.
Figure 10.
.
3
1
1
Twist Knob
2
Knob in Locked Position
3
Align “Triangle” Marks
© 2014 Toyota Motor Sales, USA
2
April 14, 2014
S-SB-0005-14
Page 10 of 12
Floor Mat Installation During PDS
Installation Procedure: Knob Style with Locking Clip (Continued)
6. Verify proper installation.
Figure 11.
NOTE
If applicable, DO NOT remove the yellow
“Caution” tag from the floor mat. This should
only be removed by the customer.
© 2014 Toyota Motor Sales, USA
.
April 14, 2014
S-SB-0005-14
Page 11 of 12
Floor Mat Installation During PDS
Installation Procedure: Pre-installed Knob Style
1. Verify that the driver and passenger side (if applicable) floor mats are for the correct model
and model year they are being installed in.
2. Align the floor mat holes with the retention clip
knobs and place the floor mat holes onto the
retention clip knobs.
Figure 12.
.
1
2
3
3. Turn the retention clip knobs a quarter of a turn to
lock in place and verify the “triangle” marks on the
retention clip knob and floor mat are aligned.
1
Retention Clip Eyelet on Floor Mat
2
Retention Clip
3
Front of Vehicle
Figure 13.
.
3
1
1
Twist Knob
2
Knob in Locked Position
3
Align “Triangle” Marks
© 2014 Toyota Motor Sales, USA
2
April 14, 2014
S-SB-0005-14
Page 12 of 12
Floor Mat Installation During PDS
Installation Procedure: Pre-installed Knob Style (Continued)
4. Verify proper installation.
Figure 14.
NOTE
If applicable, DO NOT remove the yellow
“Caution” tag from the floor mat. This should
only be removed by the customer.
© 2014 Toyota Motor Sales, USA
.