T-SB-0113-13 Rev

COROLLA
01 Install D/C Cut Fuse* (see page 2) ..................................
FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse;
turn on lights and rear defogger. Unlock doors; release fuel door.
01
02
03
04
05
06
07
08
09
Check dome, courtesy, map, and sun visor lights* ..........
Check warning/indicator lights, gauges, and horn ...........
Check windshield wipers and washers ............................
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights ..............................
Check inside/outside rear view mirror operation/
adjustment .......................................................................
Check cigarette lighter* and power outlets ......................
Check audio/navigation* systems and set clock ..............
Check sliding roof* ..........................................................
Install shift-lock override button cover…………………….
UNDER VEHICLE (ON HOIST)
OK
September 2013 Rev2
Adjust/
Adjust/
Repair
Repair
OK
BEFORE INSPECTION
Adjust/
Repair
2014 PRE-DELIVERY SERVICE CHECK SHEET
01 Remove disc brake anti-rust covers/anti-corrosion
wheel film* ………………………………………………….
02 Inspect tires for defects/damage .....................................
03 Initialize Tire Pressure Warning System (TPWS) (see
page 2) ………………………………………………………
04 Install wheel covers/caps/spare tire wheel covers* ........
05 Inspect for fuel, oil, coolant, and other fluid leaks ...........
06 Inspect under the vehicle for damage, rust, etc. ..............
07 Visually check bolts and nuts on chassis and powertrain
for looseness ...................................................................
08 Install rubber body plugs* (stored in glove box or
center console) ................................................................
ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.
Enter Odometer Readings
WALKAROUND INSPECTION
Reading Before Test: ________________ Reading After Test: ________________
Start at left front door. Check window and door lock operation (from master power
switch, if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks.
01 Check Smart Key System* ………………………………
02 Check door and door lock operation, including each
wireless remote control/theft deterrent system* ...............
03 Check window operation..................................................
04 Check that engine starts with all keys .............................
05 Check that child safety door locks are in normal
(unlocked) position ..........................................................
06 Check seats and seat belt operation ...............................
07 Check rear defogger/rear view mirror defogger* ..............
08 Check side marker, tail, backup, and license plate lights
09 Check luggage compartment light* and trim appearance
10 Adjust spare tire pressure, inspect for damage, and
check jack and tool installation ........................................
11 Check headlight aim ........................................................
UNDER HOOD
01
02
03
04
05
Check engine oil and ATM* fluid levels ...........................
Check brake and clutch* fluid levels................................
Check engine coolant level .............................................
Check windshield washer fluid level ................................
Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading: ___________%) .....
06 Inspect for fuel, oil, coolant, and other fluid leaks ...........
COMMENTS:
* Inspect or install when equipped/required.
01
02
03
04
05
06
07
08
09
10
11
12
Check cold engine operation............................................
Check engine operation during warm-up .........................
Check engine at normal operating temperature ...............
Check clutch or transmission operation ...........................
Check brake and parking brake operation .......................
Check steering operation & off-center/vehicle pull/flutter .
Inspect for abnormal noise and vibration .........................
Inspect for squeaks and rattles ........................................
Check heater and A/C operation ......................................
Check cruise control operation* …………………………..
Check front seat heater operation* ..................................
Set/calibrate compass* (see page 2) ...............................
FINAL INSPECTION AND CLEANING
01 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer) .......
02 Visually inspect all interior parts for installation,
damage, fit, dirt, etc. ........................................................
03 Verify floor mat application and install using
retaining clips* ...............................................................
04 Remove Rapgard™ and clear protective bumper film* ....
05 Wash and clean vehicle ...................................................
06 Inspect paint finish for scratches, chips, rust, dents,
damage, etc. ....................................................................
07 Inspect exterior body parts for proper installation,
damage, rust, etc. ............................................................
08 Place oil change sticker on inside of windshield, top
left corner .........................................................................
09 Place Owner’s Guide and first aid kit portfolio* in
glove box ........................................................................
10 Perform Techstream Health Check .................................
11 Install front license plate and mounting bracket* (see
page 2) ...........................................................................
Completion and retention of this from is required to comply with Toyota’s Warranty Policy.
TECHNICIAN’S SIGNATURE
SERVICE MANAGER’S SIGNATURE
NAME (PLEASE PRINT)
NAME (PLEASE PRINT)
Date
Dealer Name
Dealer Code
We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.
Vehicle Identification Number (Sticker)
D/C CUT FUSE INSTALLATION
To minimize battery discharge the D/C Cut Fuse has been removed and is stored in the
engine compartment Relay Block. Install the D/C Cut Fuse and confirm all related DTCs
are cleared.
2
DTC Clearing Procedure
1. Connect Techstream.
2. Cycle the ignition switch to the “IG-ON” position.
3. Using Techstream, check any other codes being output.
4. Erase DTCs (B1247) and Freeze Frame Data.
1
1 Remove This D/C Cut Fuse (30A)
2 Install D/C CUT Fuse (30A) Here (Original Location)
TPWS INITIALIZATION
Initialization Procedure
Refer to the Repair Manual for the Initialization procedure. Please note the spare tire does not have a TPWS sensor.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature, perform a
Health Check using Techstream and select the “Compensation Tire Pressure” checkbox. Compensation pressures will be
displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold.
COMPASS CALIBRATION
Refer to the Repair Manual for the Calibration procedure for vehicles equipped with a compass in the rear view mirror.
NOTE
 Do NOT perform calibration of the compass in a place where the Earth’s magnetic field is subject to interference
(underground parking, under a steel tower, between buildings, roof parking, near a railroad crossing, near a large
vehicle, etc.).
 During calibration, do NOT operate electric systems (moon roof, power windows, etc.) as they may interfere with the
calibration.
FRONT LICENSE PLATE & MOUNTING BRACKET* INSTALLATION
1. Insert the front license plate into the tabs on the bracket.
2. Attach the clip of bracket to the upper lip of second air intake and rotate bracket upwards.
3. Align the holes on the license plate and license plate
bracket with the dimples on the lower grille.
4. Screw the 2 self-tapping screws directly into the dimples to
install the front license plate and the front license plate
bracket.
NOTICE
 Do NOT pre-drill holes into the bumper.
 Do NOT overtighten the self-tapping
screws.
1
6
5
2
3
1
4
1
2
3
4
5
6
Dimples
Second Air Intake
Front License Plate Bracket
License Plate
Clip
Rotate Bracket
1 Self-tapping Screw